Jan 05, 2024 Leave a message

304 Stainless Steel Plate Welding Cracks: Causes, Controls and Repair

Why 304 Stainless Steel Plate Cracks During Welding

Welding cracks in 304 stainless steel plate have three distinct origins, and they must be diagnosed separately because the remedies are different. Solidification or hot cracking forms in the weld metal while the pool is still freezing; liquation cracking forms just outside the fusion line in the partially melted zone; and cold cracking driven by hydrogen or by residual stress appears hours to days after the arc stops. Sensitisation is a fourth, slower mechanism: carbide precipitation in the 450-750 °C range leaves chromium-depleted grain boundaries that crack under stress in corrosive service.

Recognising which mechanism is at work is the first step, since a preheat that helps against hydrogen cracking does nothing for solidification cracking and can even worsen it in fully austenitic welds.

Material Factors: Composition and Filler Metal

Standard grade 304 is limited to 0.07% C under ASTM A240/A240M, while 304L is limited to 0.030% C; the low-carbon version is far less prone to sensitisation during multi-pass welding. Where a corrosive environment or a thick section demands it, 304L plate is the safer base material.

For the filler metal, the standard choice is a matching low-carbon grade classified under AWS A5.9, such as ER308L for gas tungsten or gas metal arc welding and E308L for shielded metal arc welding. A small amount of delta ferrite in the austenitic weld metal, commonly targeted at roughly 3 to 10 ferrite number, resists solidification cracking by changing the solidification mode. Fully austenitic weld metal, produced by a filler with no ferrite potential, is far more crack-sensitive and requires different controls.

Preheat and Interpass Temperature

Preheat is used to drive off surface moisture, reduce the cooling rate and lower the restraint stress. For austenitic stainless steel the preheat level is much lower than for carbon steel, typically 100-150 °C for heavy or highly restrained joints, and the interpass temperature should be held below about 150 °C to preserve corrosion resistance and avoid hot cracking. Heating the whole joint area uniformly for 15-30 minutes before the first pass is the practical way to reach a stable starting temperature on thick 304 plate.

Overheating must be avoided. Excessive preheat increases the width of the heat-affected zone, promotes carbide precipitation and, in fully austenitic welds, increases the risk of solidification cracking.

Welding Parameters and Technique

Parameter Practical control
Heat input Keep in the middle of the qualified range; high input widens the HAZ, low input raises cooling rate and restraint stress
Current and voltage Use the lowest current that gives full penetration; avoid long, wandering arcs
Travel speed Steady, matched to current so that bead shape stays uniform
Torch angle Keep near perpendicular to limit heat concentration on one side
Bead sequence Balance passes on both sides of the joint, use back-step or skip sequence to spread stress
Cleaning Remove oil, moisture, marker ink and oxide; never use carbon steel brushes

Distortion control and crack control are related: a joint that is free to move as it cools develops lower residual stress. Tack spacing, fit-up and the use of strongbacks or fixtures should follow a written procedure rather than shop habit, and the procedure should be qualified to ASME BPVC Section IX or EN ISO 15614-1.

Post-Weld Treatment and Repair

Three measures are used after welding. Mechanical treatment such as grinding blends the toe of the weld, removing the stress concentration where fatigue cracks normally start. Solution annealing at roughly 1040-1120 °C followed by rapid cooling re-dissolves carbides and restores corrosion resistance in the heat-affected zone, but it is difficult to apply to large fabricated structures. Stress relief below the sensitisation range does not restore corrosion resistance and cannot be used as a substitute.

When a crack is found, the repair should start with complete removal of the cracked metal, verified by dye penetrant testing, followed by re-welding with the same qualified procedure and, where the service is corrosive, a check of the repaired area using the intergranular corrosion test practices of ASTM A262.

Frequently Asked Questions

Q: What is the most common cause of cracking when welding 304 plate?
A: Solidification cracking in the weld metal and high restraint stress in the joint. In practice they appear together when heat input is wrong, the joint is over-restrained, and the filler metal produces fully austenitic weld metal.

Q: Should 304 or 304L be selected to avoid cracks?
A: 304L. With a carbon ceiling of 0.030% instead of 0.07%, it resists grain-boundary carbide precipitation far better in multi-pass or repair welding and in hot service.

Q: What interpass temperature is acceptable?
A: Keep the interpass temperature below about 150 °C for austenitic stainless steel. This limits carbide precipitation and reduces both hot cracking and distortion.

Q: Does preheating solve stainless steel welding cracks?
A: Only for hydrogen-related and restraint-related cracking, and only at the low levels used for austenitic steel. Excessive preheat makes solidification cracking worse because it widens the weld pool and the heat-affected zone.

Q: Which filler metal should be used?
A: A low-carbon matching electrode classified under AWS A5.9, generally ER308L or E308L, chosen so that the weld metal retains a small ferrite content and the deposited carbon stays low.

Q: How is a cracked weld repaired correctly?
A: Excavate the crack completely and confirm removal with penetrant testing, re-weld with the qualified procedure, inspect again, and verify corrosion resistance in the repaired zone where the service is aggressive.

Send Inquiry

whatsapp

phone

Email

Inquiry