Oct 12, 2024 Leave a message

ASTM-A588-A588M Standard Specification.pdf

A588 Grade B Corten Steel Properties, Welding and Applications

Grade B Within the A588 Family

ASTM A588/A588M covers four grades of high-strength low-alloy structural steel intended for welded, riveted or bolted construction where weight saving matters and where the steel will be exposed to the atmosphere. Grade B sits in the middle of the family: it uses a moderate copper addition with chromium and a small amount of vanadium, and it is the grade most often rolled as plate for bridge and building work. The same chemistry and mechanical requirements are called up by ASTM A709/A709M Grade 50W when a bridge specification is used, and a closely equivalent material appears in EN 10025-5 as the S355J0W and S355J2W grades and in GB/T 4171 as Q355NH.

The practical value of Grade B is a combination that plain carbon steel cannot offer at the same strength level: a minimum yield strength of 345 MPa without quench and temper treatment, adequate toughness at ambient and moderately low service temperatures, ordinary shop weldability with low-hydrogen consumables, and an oxide layer that stabilises in many outdoor atmospheres. It is not a stainless steel and it is not a wear-resistant plate; misunderstanding either point is the most common source of disappointment.

Chemistry Across the Four Grades

The grades differ mainly in their copper, chromium and nickel balance, and that balance controls how quickly a protective layer forms. The table gives the heat analysis windows that characterise each grade in the specification; the carbon, manganese, phosphorus, sulphur and silicon limits are broadly similar across the family, with carbon at 0.20% maximum and manganese between roughly 0.75% and 1.25% for plate grades.

Grade Cu, % Cr, % Ni, % Typical emphasis
A 0.25 - 0.40 0.40 - 0.65 0.40 max General structural plate and shapes, widely available
B 0.20 - 0.40 0.40 - 0.70 0.50 max Plate for bridges and buildings, balanced toughness and corrosion behaviour
C 0.30 - 0.50 0.40 - 0.70 0.50 - 0.80 Higher alloy content for more demanding atmospheric exposure
K 0.30 - 0.50 0.40 - 0.70 0.50 - 0.80 Higher strength weathering grade, often used in heavy structural work

Vanadium in the range 0.01% to 0.10% is specified for Grade B and contributes precipitation strengthening in the as-rolled condition. Because the specification controls ranges rather than exact values, two compliant heats can differ enough to show visibly different patina development over the first two years. Purchasers who need consistency across a project should ask for the actual heat chemistry on the mill certificate and compare heats rather than accepting a generic compliance statement.

Mechanical Properties and Design Consequences

Grade B is specified with a minimum yield strength of 345 MPa and a minimum tensile strength of 485 MPa, with elongation of 21% minimum in a 50 mm gauge length, or 18% minimum in a 200 mm gauge length, for plate in the as-rolled condition. These are minimum values, and mills typically deliver 20 to 60 MPa above the minimum yield, which is useful when a connection design has little margin.

Property Specified minimum, Grade B Design implication
Yield strength 345 MPa About 1.4 times the yield of Q235B or A36 at similar thickness, allowing lighter sections
Tensile strength 485 MPa Governs bolt bearing and net-section checks
Elongation 21% in 50 mm Confirms ductility for plastic redistribution in redundant structures
Carbon equivalent Not fixed by the grade Must be calculated from the actual heat for welding procedure qualification
Impact energy Not fixed by the base grade Order Charpy testing by supplementary requirement when service temperature is below 0 degrees C

Thickness changes the picture. Plate rolled above roughly 40 mm carries less total reduction, so toughness at the plate centre and through-thickness ductility fall, and the risk of lamellar tearing in heavily restrained T-joints rises. Where such joints are unavoidable, specify through-thickness testing to ASTM A770 and a sulphur level below 0.010% so that inclusion stringers do not open up under weld shrinkage.

The specification does not impose impact testing in its base form. Bridge projects almost always add it, and for structures erected in cold climates or carrying dynamic load, Charpy testing to ASTM A370 at a stated test temperature should be treated as a mandatory addition to the order rather than an optional extra.

Weldability and Procedure Control

Grade B is weldable by shielded metal arc, gas metal arc, flux-cored arc and submerged arc processes, using the same general practices applied to structural carbon steel of similar strength, with two differences that matter: the alloy content raises hardenability slightly, and the corrosion behaviour of the weld area must be considered as well as its strength.

Consumables should match the 485 MPa tensile level rather than the 345 MPa yield level. Low-hydrogen electrodes of the E7018 classification, or their wire equivalents, are the normal choice; rutile electrodes are unsuitable for restrained joints and for plate thicker than about 20 mm. Hydrogen control is the single most important variable: electrodes must be kept in a holding oven at the manufacturer's stated temperature, and flux for submerged arc must be dried before use.

Preheat requirements follow carbon equivalent and thickness rather than grade name. For plate up to about 25 mm with carbon equivalent below 0.40, a preheat of 50 to 100 degrees C is generally adequate for shop conditions above 5 degrees C ambient. Above 40 mm, or where carbon equivalent approaches 0.45, a preheat of 100 to 150 degrees C with interpass temperature control is prudent, and a qualified procedure should be established by testing rather than by rule of thumb. Bridge work is normally welded under AWS D1.5, and general structural work under AWS D1.1 or ISO 3834 quality requirements, whichever the contract names.

Heat input should be controlled within the qualified range. Excessive heat input coarsens the heat-affected zone and reduces toughness; very low heat input with thick plate increases the risk of hard, crack-susceptible microstructures. For weathering steel, weld metal and heat-affected zone composition should be reasonably matched to the parent metal in copper and nickel so that the weld does not become a preferential corrosion path. Where the joint will remain unpainted, grinding the weld toes flush and removing all slag prevents localised attack along the toe line.

Cutting, Forming and Machining

Plates can be sheared up to moderate thickness, but flame cutting or plasma cutting is preferred for thicker sections and for edges that will be exposed. Flame-cut edges should be inspected for notches and drag lines and dressed where a fatigue-sensitive detail is involved. Thermal cutting leaves a thin oxide layer on the cut face which weathers more slowly than the rolled surface; it is cosmetic in most cases but should be removed where a uniform appearance is required.

Cold forming is straightforward at the strength level of Grade B. Minimum bend radii in the region of two to three times plate thickness across the rolling direction are typical shop practice, with slightly larger radii when bending parallel to the rolling direction where edge cracking is a risk. Grade B has adequate ductility for the bend radii used in structural detailing but is not intended for severe cold forming; stretching and severe flanging call for stress relief afterwards.

Machining and drilling are performed with carbide tooling at speeds slightly lower than those used for mild steel, and with adequate coolant. The alloy content produces a somewhat tougher chip and more tool wear, which is a cost factor in plates with hundreds of bolt holes; laser or plasma hole making is usually more economical than drilling on large bridge girders.

Connections: Bolted, Welded and Mixed

High-strength friction-grip bolting is standard for field connections. Bolts, nuts and washers of a weathering grade should be specified so that the fastener develops a patina similar to the plate; ordinary galvanised fasteners stay bright and create a visible contrast as well as a galvanic couple. Slip factors for weathering steel faying surfaces depend on the surface treatment specified, and the treatment stated in the procedure must match what is actually done in the shop, because a painted faying surface and a blast-cleaned one give very different slip resistance.

In welded connections, complete joint penetration groove welds are used where fatigue or seismic detailing requires them, with backing bars removed and the root gouged and re-welded on demand. Seal welds should be continuous around members that would otherwise form a crevice, because an unsealed gap between two weathering steel surfaces holds water indefinitely. Where a weathering member meets a painted carbon steel member, the connection should be detailed so that water drains away from the contact face and, where practical, the two are separated by a barrier layer.

Where Grade B Is Used, and Why

The applications below reflect the material's real strengths: an exposed structural element that benefits from low maintenance and can accept a dark brown finish that changes with time.

Application Why Grade B fits Design caution
Highway and railway bridges, plate girders Strength with unpainted durability, good field weldability, established bridge specifications Add toughness testing; detail drainage at deck joints and bearings
Building frames and exposed architectural steel Uniform patina as a finish, reduced painting cycles Runoff staining must be accepted; sheltered facades may not darken evenly
Transmission poles and lighting columns Slender sections, low maintenance in rural and urban atmospheres Avoid water traps at base plates and cap plates
Rail wagons, frames and containers Abrasion plus atmospheric exposure, repairable by welding Not a substitute for wear plate in high-abrasion liners
Industrial structures and conveyor galleries Moderate sulphur atmospheres, exposed framing Check chloride and acid deposition; coat where aggressive
Retaining structures and sheet piling above ground Weathering in the exposed zone Below grade the layer cannot form; use a coated or higher-alloy option

The applications where the material is misapplied follow the same logic in reverse. Grade B is not suitable for tanks, pipes or any surface in continuous contact with water, for buried foundations, for marine splash zones, for chimney liners exposed to condensate, or for chutes and hoppers where abrasion dominates. In those positions the steel performs like an ordinary low-alloy structural plate and the expected maintenance saving does not materialise.

Ordering, Tolerances and Acceptance

An order for Grade B plate should state the specification and grade, dimensions with edge condition, the surface condition required, and any supplementary requirements. Dimensions and mass tolerances are governed by ASTM A6/A6M unless the contract states otherwise, and that standard also defines camber, flatness and edge straightness limits that determine how much straightening the fabricator must budget for.

Documentation should include a mill test certificate with heat number, ladle and product analysis, tensile results and, where ordered, impact results. Certificates issued to EN 10204 type 3.1 are the norm for structural work in many markets and provide traceability from heat to plate. Ultrasonic examination to ASTM A578 is ordered for thick plate in critical tension members or where through-thickness properties matter. Visual acceptance covers surface defects, laminations at cut edges and the condition of the rolled surface, and any repair welding of surface defects requires a qualified procedure and subsequent inspection.

Life-Cycle Comparison and Common Misreadings

Compared with painted carbon steel, unpainted Grade B removes the initial coating cost and the recurring access, surface preparation and repainting cost, and it avoids the environmental burden of coating removal. The trade-off is a higher plate price, a restricted set of acceptable exposures, and an appearance that cannot be specified precisely because it depends on climate. In a moderate atmosphere with good detailing, the unpainted option is usually the lower whole-life cost; in a coastal or chemically aggressive site, a properly coated Grade B or a different material will be cheaper over thirty years.

Three misreadings recur. First, Grade B is not a corrosion-proof steel: it slows atmospheric attack and depends on a wet-dry cycle that the designer must provide. Second, it is not a wear-resistant grade; its hardness in the as-rolled condition is far below that of a quenched and tempered abrasion plate, and using it in a chute will produce rapid loss. Third, a higher alloy content in Grade C or Grade K does not license use in a chloride-rich environment that would reject Grade B; it only shifts the boundary slightly.

FAQ

Q: What is the minimum yield strength of A588 Grade B plate?
345 MPa, with a minimum tensile strength of 485 MPa and elongation of 21% in a 50 mm gauge length for plate in the as-rolled condition.

Q: Can Grade B be welded without preheat?
For thin plate in warm shop conditions with low carbon equivalent, a modest preheat is still normal practice. Above about 25 mm, or with carbon equivalent near 0.45, preheat of 100 to 150 degrees C should be applied under a qualified procedure.

Q: Is Grade B the same as S355J2W?
They are closely comparable weathering structural steels with similar strength levels and alloying philosophy, but they are different specifications with different chemistry windows and testing rules, so a substitution requires engineering approval and a check of the mill certificate.

Q: What bolts should be used with weathering steel?
Fasteners of a weathering grade that develops a compatible patina. Galvanised or plain carbon fasteners remain visually different and create a small galvanic couple at each connection.

Q: Can Grade B be used for a storage tank shell?
No. A tank shell is wetted on one face and often on both, so the protective layer cannot stabilise. Use a coated steel or a grade selected for the stored medium.

Q: Does a thicker plate have lower toughness?
Generally yes. Higher thickness means less rolling reduction and slower cooling, so centre-line toughness falls and through-thickness ductility becomes a concern. Impact testing and, where relevant, through-thickness testing should be ordered explicitly.

Q: How should cut edges and weld toes be treated?
Dress sharp edges and grind weld toes smooth, and remove all slag. These are the locations where water collects and where localised attack begins on an unpainted structure.

Send Inquiry

whatsapp

phone

Email

Inquiry