What Are AR400, AR450 and AR500 Abrasion Resistant Steel Plates?
AR400, AR450 and AR500 are quenched and tempered abrasion resistant (AR) steel plates whose grades are defined by their minimum Brinell hardness: 400 HB, 450 HB and 500 HB respectively. These plates are produced in the plate mill with a controlled thermal cycle that hardens the surface while preserving enough toughness for structural service. Because wear resistance rises with hardness, the AR series is specified where equipment parts are exposed to sliding abrasion from ore, sand, gravel, coal and similar bulk materials. The three grades share the same family logic: the higher the number, the harder the plate, the better the wear life, and the more demanding the fabrication.
Hardness, Strength and Toughness Comparison
The table below compares the key mechanical values as published for the three grades. Actual delivered values are stated on the mill test certificate for each heat.
| Property | AR400 | AR450 | AR500 |
|---|---|---|---|
| Minimum Brinell hardness (HB) | 400 HB | 450 HB | 500 HB |
| Tensile strength (MPa) | 1500–1900 | 1700–2100 | 1800–2200 |
| Yield strength (MPa) | ≥1000 | ≥1100 | ≥1200 |
| Impact toughness (J at −40 °C) | ≥18 | ≥20 | ≥20 |
Two practical consequences follow from these numbers. First, hardness drives wear life: in the same abrasive environment an AR500 liner can outlast an AR400 liner by roughly 2.5 to 3 times before replacement. Second, the rise in hardness and strength reduces formability and increases cutting and welding difficulty, which is why grade choice must balance wear life against fabrication cost.
AR400: Cost-Effective Wear Protection for Light to Moderate Abrasion
AR400 is the entry level of the AR family and the most forgiving to fabricate. It suits low-to-moderate abrasion duties where extreme hardness would add cost without benefit. Typical uses include skid-steer loader buckets, small excavator attachments, concrete mixer drums, rice hullers, fertilizer spreader components, grain elevator buckets, conveyor structures handling coal fines or wood chips, storage bin liners, small garbage truck bodies and recycling sorter parts. Because it cuts and welds more easily than AR450 or AR500, AR400 is a practical choice for custom, small-batch fabrication and for parts replaced on a planned maintenance cycle.
AR450: The Balanced Intermediate Grade for Medium Abrasion
AR450 offers roughly 12.5% higher hardness than AR400 (450 HB versus 400 HB) while retaining acceptable workability, which makes it the preferred grade for medium-abrasion equipment where cost and performance must align. Common applications are conveyor idlers, ore hoppers and small crusher liners in mineral processing, dump truck sidewalls, backhoe buckets and asphalt paver screeds in heavy construction, trailer floors for hauling sand and gravel, and fan blades, pulverizer components and light shredder parts in industrial machinery. In practice the longer wear life of AR450 often offsets its small price premium over AR400, particularly on parts that are expensive to replace or cause downtime when they fail.
AR500: Maximum Hardness for Severe, High-Impact Abrasion
AR500 is the premium grade of the series, specified for severe abrasion with heavy impact. At 500 HB it delivers the longest service life in the family and is the standard choice for large crusher liners, jaw crusher plates and ore chutes in hard-rock mining, excavator buckets, bulldozer blades, mining truck beds, cone crusher components, screen decks and sand-washing machine parts handling silica-rich material. The combination of 500 HB hardness with the −40 °C toughness values shown in the table also makes AR500 usable in arctic mining equipment. For extreme-impact positions, however, a tougher grade may still outperform AR500, so the application must be assessed for impact energy as well as abrasion.
Choosing the Right Grade: Cost, Service Life and Maintenance
Grade selection is ultimately an economic decision. AR400 has the lowest initial and fabrication cost, the highest maintenance frequency and the shortest wear life. AR450 costs about 10–15% more than AR400 and typically delivers 1.5 to 2 times the service life. AR500 costs about 20–25% more than AR400 and typically delivers 2.5 to 3 times the service life, which usually gives it the lowest cost per year of service for critical, high-wear components. AR400 is the better choice for complex shapes and tight budgets, while AR500 reduces downtime and replacement cost in severe duties. For most medium-wear equipment, AR450 is the balanced recommendation.
Fabrication Considerations
Hardness comes with processing constraints. All three grades should be cut by plasma, laser or waterjet where possible, and drilled with carbide tooling at reduced speeds. Welding requires low-hydrogen consumables and, for AR450 and AR500, preheat and controlled heat input to avoid hydrogen cracking; the high hardness of AR500 may require qualified welding procedures in highly restrained joints. Hardness at the flame-cut edge is often reduced by heat-affected-zone softening, so edges exposed to wear should be considered in the design.
Frequently Asked Questions
What does the number in AR400, AR450 and AR500 mean?
The number is the minimum Brinell hardness in HB: AR400 is nominally 400 HB, AR450 is 450 HB and AR500 is 500 HB. Hardness is the primary indicator of abrasion resistance in this family.
Is AR500 always better than AR400?
Not always. AR500 wears longest but costs more, is harder to cut and weld, and has lower toughness. For light abrasion and complex fabrication, AR400 can be the most economical choice over the equipment life.
Can AR500 steel plate be welded?
Yes, with low-hydrogen consumables, adequate preheat and controlled heat input. Because of the high carbon equivalent, welding procedures should be qualified and the heat-affected zone hardness monitored.
What thickness range is typical for AR plates?
AR400, AR450 and AR500 plates are commonly supplied from 3 mm up to about 100 mm, with 4–50 mm covering most liner and bucket applications. Thickness capability depends on the mill and the governing specification.
How do I verify the actual hardness of delivered AR plate?
Ask the supplier for the mill test certificate of the specific heat and, if required, verify with a Brinell hardness test on the delivered plate. Hardness can vary through thickness and across the plate surface, so sampling should follow the agreed standard.




