Jul 08, 2025 Leave a message

ASTM-A588-A588M Standard Specification.pdf

ASTM A588, A242 and A606 Type 4 Weathering Steel Sheet in 10 and 12 Gauge

Three Weathering Steel Specifications Compared

ASTM A588/A588M, ASTM A242/A242M and ASTM A606 cover different product forms of the same idea: low-alloy steel that forms a protective oxide layer instead of losing section to ordinary rust. A588 is the structural plate and shape specification, A242 is the older high-strength low-alloy specification for plates, shapes and bars, and A606 Type 4 is written for thin sheet and strip. Buyers who need sheet in 10 or 12 gauge normally land on A606 Type 4 or on A588 plate cut to size, so the difference in scope matters as much as the difference in chemistry.

Gauge to Millimetre Conversion

Gauge (US standard for sheet steel) Thickness, in Thickness, mm
10 0.1345 3.416
12 0.1046 2.657
14 0.0747 1.897
16 0.0598 1.519

Gauge numbers are only meaningful with the gauge system named. A 10 gauge weathering sheet order should always be written as 10 gauge plus a millimetre or inch range, because the tolerance on a nominal gauge is a large fraction of the thickness.

Mechanical Requirements

Specification Product form Minimum yield strength Minimum tensile strength
ASTM A588/A588M Plate, shapes 345 MPa (50 ksi) 485 MPa (70 ksi)
ASTM A242/A242M Plate, shapes, bars 345 MPa (50 ksi) 480 MPa (70 ksi)
ASTM A606 Type 4 Sheet, strip 340 MPa (50 ksi) 480 MPa (70 ksi)

Values apply to the thinner ranges of each specification; heavy sections carry reduced minima in the thickness tables of the standards. A606 adds copper with chromium and nickel for atmospheric corrosion resistance and is supplied for sheet and strip rather than for structural plate.

How the Patina Forms

The alloying elements slow the conversion of surface iron to soluble corrosion products, so the oxide that forms is fine grained and stays in place. Alternate wetting and drying is essential: the layer only becomes protective when the surface dries between wettings. Sheet used for cladding, rain screens and fascia panels normally reaches a stable dark brown surface within a few seasons of exposure, and the appearance then changes only slowly. Details must shed water, and pockets that trap leaves, soil or salt will corrode regardless of the grade.

Applications for 10 and 12 Gauge Sheet

Architectural cladding and rain screens, facia and balustrade panels, planters and landscape features, sculpture and signage, containers and truck body panels, industrial ducting, machine guards and cable trays. In thin sections the material is chosen for appearance and maintenance cost, not for load capacity, so designs that need real bending strength usually move to plate thicknesses or to a different grade.

Cutting, Forming, Welding and Finishing

Sheet is cut by shearing, laser, plasma or water jet; laser cutting leaves the cleanest edge for exposed architectural work. Cold forming bends should use radii sized to the sheet thickness and the grain direction to avoid cracking on the outside of the bend. Welding is straightforward with mild steel consumables, but the weld and its heat affected zone do not contain the alloying elements of the parent sheet and will rust preferentially unless filler matching the base metal's corrosion resistance is used. Fixings should be of a compatible weathering material or be isolated from the sheet; stainless steel or galvanised fasteners in direct contact create a galvanic couple in wet service. Bare sheet can also be left to weather behind a clear protective treatment, or painted, but a coating hides the surface and must be maintained.

Frequently Asked Questions

Q: Which specification applies to weathering sheet in 10 or 12 gauge?
A: ASTM A606 Type 4 covers sheet and strip; A588 covers plate and shapes, so thin material is normally ordered to A606.

Q: How thick is 10 gauge and 12 gauge sheet?
A: About 3.416 mm and 2.657 mm in the US standard gauge for sheet steel, subject to the mill tolerance.

Q: What is the minimum yield strength of these grades?
A: 345 MPa for A588 and A242 plate, and 340 MPa for A606 Type 4 sheet, in the applicable thickness range.

Q: Will the sheet rust through if left bare?
A: Not in a freely draining, periodically dry atmosphere; the protective layer keeps metal loss very low after it stabilises.

Q: Can bare weathering sheet be used near the coast?
A: It is not recommended. Airborne chloride keeps the surface wet and the protective layer does not stabilise, so a coated steel is a better choice.

Q: Do fixings need to match the sheet?
A: Yes in practice. Fasteners of the same weathering family, or isolated fasteners, avoid preferential corrosion and staining around the fixing.

Send Inquiry

whatsapp

phone

Email

Inquiry