What Is ASTM A612 / ASME SA612 Steel?
ASTM A612 is the specification for high-strength carbon steel plates for welded pressure vessels in moderate and lower temperature service. The steel is fully killed, fine-grained carbon-manganese-silicon material, and ASME SA612 is the identical grade adopted by the ASME Boiler and Pressure Vessel Code. Its minimum yield strength of 345 MPa and tensile range of 570–725 MPa give it a clear strength advantage over conventional carbon vessel steels, which is why it is used for pressure vessels, boilers and storage tanks where higher allowable stress and reduced wall thickness matter.
How the Equivalents Compare
The table below summarises the most frequently cited equivalents for A612/SA612. All values are minimum or range figures for the thinnest common thickness tier, and the impact temperatures refer to the grade's typical testing condition:
| Grade | Standard | Yield (MPa) | Tensile (MPa) | Typical impact |
|---|---|---|---|---|
| A612 / SA612 | ASTM / ASME | 345 | 570–725 | by agreement |
| P355N | EN 10028-3 | 355 | 490–630 | 27 J at −20 °C |
| P460N | EN 10028-3 | 460 | 550–720 | 27 J at −20 °C |
| P460NL1 | EN 10028-3 | 460 | 550–720 | 27 J at −50 °C |
| SM53B / SM53C | JIS G3106 | about 275 | about 570–720 | by agreement |
| Q345R | GB/T 713 | 345 | 510–640 | 34 J at 0 °C |
No listed grade is an exact duplicate of SA612, so substitution always requires checking the design code and the acceptance criteria of the project.
European Equivalents: EN 10028-3 P355N and P460N
P355N is the most widely recognised European candidate: it matches SA612 closely in yield strength (355 MPa versus 345 MPa) and shares the fine-grained, weldable character of the American grade, but its tensile strength is lower and its standard impact test is at −20 °C rather than a colder project temperature. P460N raises the yield to 460 MPa for heavier-duty vessels and weight-critical structures, and P460NL1 adds a −50 °C impact guarantee, which is stronger than the SA612 low-temperature option in many project specifications.
Japanese Equivalents: JIS SM53B and SM53C
In Japanese practice, SM53B and SM53C (JIS G3106) are the primary candidates for pressure vessel and welded structure service. They offer high tensile strength and good weldability, but their minimum yield strength is lower than SA612 (about 275 MPa in the thin-thickness tier), so the design must be rechecked for wall thickness when substituting. SM53C is the slightly stricter variant with additional testing requirements.
Chinese Equivalent: GB/T 713 Q345R
Q345R is the most widely used pressure vessel steel in China and the closest domestic candidate to SA612. It matches the 345 MPa minimum yield in the thin tier, has a tensile range of 510–640 MPa, and is available with low-temperature impact options such as the D-grade variants used for colder service. The former designation 16MnR is the historical name of the same grade family. Q345R is a reasonable substitute in non-code projects, but for ASME or export applications where SA612 is explicitly required by the specification, the substitution must be approved by the designer and the inspection authority.
Selection Guide
General pressure vessels in European projects: P355N or Q345R offer the closest balance of properties and availability. High-pressure or weight-critical systems: P460N provides a 460 MPa yield for thinner walls. Low-temperature duty: P460NL1 (−50 °C) exceeds the typical SA612 project requirement. Japanese projects: SM53B/SM53C satisfy local certification needs. Chinese projects: Q345R gives local compliance at competitive cost. In every case, the governing design code decides whether the equivalent is acceptable.
Frequently Asked Questions
Is SA612 the same as A612?
Yes. SA612 is the ASME Boiler and Pressure Vessel Code designation of ASTM A612; the chemistry and mechanical requirements are the same, and the only difference is the code system in which the material is documented.
What is the composition of ASTM A612?
A612 is a killed carbon-manganese-silicon steel with carbon up to 0.25%, manganese 1.00–1.50%, silicon 0.15–0.50%, and phosphorus and sulfur each limited to 0.035%, giving a fine-grained, weldable pressure vessel plate.
Can Q345R be used as a substitute for SA612?
In some non-ASME working conditions, yes. For export projects or where the specification explicitly requires SA612, substitution should not be made without designer and inspection authority approval, because the chemistry and impact requirements differ.
What are the yield and tensile strengths of SA612?
The minimum yield strength is 345 MPa (50 ksi) and the tensile strength range is 570–725 MPa (83–105 ksi) for the thin-thickness tier, with slightly reduced tensile values for thicker plates per the standard's table.
Does SA612 require impact testing at −40 °C?
ASTM A612 does not mandate Charpy testing by default. A −40 °C impact requirement is a common project or supplementary specification; when required, the test temperature and acceptance energy must be defined in the purchase order.
What is the typical thickness range of SA612 plate?
The routine range is 6–100 mm, with customized thicknesses available from some mills up to about 150 mm subject to rolling and heat treatment capability.




