Corten A and B: What the Two Weathering Grades Have in Common
Corten A and Corten B are the two classic high-strength, low-alloy weathering steels. Both are designed to develop a protective, rust-like patina when exposed to the weather, and that oxide layer slows further corrosion to a fraction of the rate of untreated carbon steel, which is why the grades are chosen for structures that stay outdoors and cannot be repainted on a practical cycle. Both are supplied as plate, sheet and coil, both are weldable and formable with ordinary fabrication equipment, and both are normally used bare.
The two grades also share the same alloying philosophy. Copper and phosphorus promote a dense, low-porosity oxide; chromium stabilises it in industrial and marine atmospheres; nickel improves toughness and helps the layer hold up where chlorides are present. Weathering grades are therefore alloy steels, not painted carbon steel, and a plain structural grade cannot be substituted without losing the very behaviour the design depends on.
How Grade A and Grade B Differ
The differences are modest but they decide which grade suits a given structure.
| Feature | Corten A type | Corten B type |
|---|---|---|
| Alloying idea | Higher phosphorus with copper, chromium and nickel additions | Low residual phosphorus, relying on manganese, copper, chromium, nickel and vanadium |
| Strength level | Weathering structural grade, minimum yield 345 MPa | Weathering structural grade, minimum yield 345 MPa |
| Typical use | Architectural panels, facades, exposed structures where the patina look is wanted | Bridges, towers, frames and heavier welded structures |
| Welding behaviour | Higher phosphorus content calls for care in heavily restrained or thick welded joints | Preferred where welding quality is critical and thick sections are joined |
In international standards the two families correspond to grades such as ASTM A588 Gr.A and Gr.B, ASTM A242, ASTM A606 Type 4, EN 10025-5 S355J0W and S355J2W, GB/T 4171 Q355NH and JIS G3125 SPA-H. Each of these is specified with a minimum yield strength of about 345 to 355 MPa and a minimum tensile strength in the region of 485 MPa, together with impact requirements that depend on the grade and thickness.
Plate Sizes, Delivery Condition and Inspection
| Parameter | Availability |
|---|---|
| Thickness | Cold rolled 0.3 mm to 1.5 mm in standard steps; hot rolled 1.6 mm to 40 mm in the usual increments |
| Width and length | Cut to the ordered size within normal plate mill limits |
| Condition | Hot rolled and annealed coil, or cut to length plate |
| Surface | Mill finish, descaled, blast cleaned |
| Packing | Seaworthy export packing, or packed to the buyer's specified method |
| Quality documents | Mill test certificate supplied with the goods; third-party inspection available |
Where the Grades Are Used
Infrastructure: bridges, guardrails, railway structures and transmission towers
Architecture: facades, roofing, canopies and exposed structural frames
Industrial: storage tanks, silos and container structures
Landscape: retaining walls, planters, fencing and sculpture
Transport equipment: rolling stock and container frames
Weathering grades suit structures that are exposed to the atmosphere and can dry out between wet periods. Where steel is permanently immersed, buried, or enclosed in damp, unventilated conditions, the protective oxide cannot stabilise and a coated or stainless solution is usually more appropriate.
What Actually Drives the Plate Price
Buyers often look for a single unit price, but a weathering plate quotation is built from several variables that move independently.
Grade and chemistry: higher alloy content, especially copper, nickel and chromium, raises the input cost, and a low-phosphorus welding grade is priced differently from an architectural grade.
Thickness and width: thin cold rolled sheet and heavy plate sit at opposite ends of the mill cost curve; unusual widths and lengths add cutting and yield losses.
Order quantity: full mill quantities allow the most efficient rolling schedule, while small or mixed orders carry higher per-tonne processing and handling costs.
Delivery condition and surface: descaled, blast cleaned or specially finished material costs more than a plain mill finish.
Certification and inspection: third-party inspection, additional mechanical tests and non-standard documentation add to the price of the consignment.
Trade terms and logistics: the chosen delivery term, port of loading and transport distance change the landed cost even when the mill price is unchanged.
Market movement: alloy surcharges and mill availability fluctuate with raw-material and energy costs, so a quotation is normally valid for a limited period.
Practical advice for buyers is to specify the grade and standard that the structure actually needs, fix the thickness range and tolerance class, and confirm the inspection and documentation requirements at the enquiry stage - these three items decide most of the spread between suppliers.
Frequently Asked Questions
Q: Is Corten A stronger than Corten B?
No. Both are specified at a minimum yield strength of about 345 MPa; the meaningful difference lies in phosphorus level, welding behaviour and the applications each grade suits.
Q: Can the plate be welded?
Yes. Both grade families weld with low-hydrogen consumables matched to the strength level; thicker and more restrained joints need a qualified procedure and suitable preheat.
Q: Does the surface rust through?
The patina forms a stable barrier that greatly slows further corrosion, provided the steel is exposed to alternating wet and dry conditions and is detailed to drain freely.
Q: Can it be painted instead of left bare?
It can, but painting removes the main advantage of a weathering grade; paint is normally chosen only for a specific colour requirement or a hostile environment.
Q: How is the plate packed for export?
Seaworthy packing suited to sea transport is standard, and packing can be adjusted to the buyer's handling method or destination port conditions.
Q: What information is needed for an accurate quotation?
The grade and standard, thickness and tolerance, width and length, quantity, delivery condition, required inspection and the delivery term, since each of these changes the final price.




