Jan 28, 2026 Leave a message

Does ASME SA517 Grade E Require PWHT? Code Rules Explained

Does SA517 Grade E Require PWHT?

For structural applications, PWHT is generally not mandatory for SA517 Grade E. For pressure-vessel construction per ASME BPVC Section VIII Div.1, PWHT requirements depend on thickness, welding procedure and the applicable UHT rules (e.g., UHT-56). Always verify with the governing code edition and the fabricator's welding procedure specification (WPS).

ASME SA 517 Grade E

What Is SA517 Grade E?

ASME SA517 Grade E is a premium-grade alloy steel plate that undergoes a liquid quench followed by high-temperature tempering to achieve a minimum yield strength of 100,000 psi. It is defined by its ability to perform in "heavy-section" applications where thinner grades like Grade B would not meet the design thickness requirements. This material is essential for modern engineering projects that demand high safety factors in high-pressure environments, such as large-scale petrochemical reactors and stationary high-pressure gas storage.

 

Key Characteristics

Resistance to Softening: Holds its properties well during moderate post-weld thermal cycles.

Purity: Low sulfur and phosphorus content to ensure high weld-joint efficiency.

Consistent Hardness: Delivers a predictable Brinell hardness range (typically 235–293 HBW).

Ductility: Retains 14–16% elongation, allowing for safe deformation before failure.

 

Grade Designation

"SA": "S" stands for Section II (Materials) of the ASME Code. "A" indicates it is a Ferrous Material (iron-based).

"517": This is the specific material specification for "Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered."

"Grade E": This identifies the specific chemical composition (Cr-Mo-Cu) and thickness range, allowing for plates up to 6 inches (150 mm) thick.

 

Comparison (vs. SA517 Grade B)

  • Thickness Capability: Grade E supports plates up to 6"; Grade B is limited to 1.25"
  • Alloying Strategy: Grade E uses Copper (Cu) for enhanced corrosion and strength; Grade B relies on Boron.
  • Application Scope: Grade B is for lightweight transport; Grade E is for heavy stationary vessels.
  • Through-Thickness Uniformity: Grade E's chemistry is more robust for maintaining core strength in thick sections.

info-706-337

Common Applications

LPG Storage Bullets: Large-scale horizontal pressurized tanks.

Ammonia Converters: High-pressure chemical reactors in fertilizer plants.

Subsea Accumulators: Deep-sea pressure-retaining components for oil and gas.

Rocket Engine Test Stands: Structures subjected to extreme vibratory and pressure loads.

 

What is the silicon content in SA517 Grade E?

The silicon content in ASME SA517 Grade E typically ranges from 0.15% to 0.40%. Silicon is an important element that helps improve the steel's deoxidation and resistance to high-temperature oxidation. It contributes to the material's strength and heat resistance, which is particularly important for applications that involve high-temperature, high-pressure conditions, such as in pressure vessels and reactors.

 

Is SA517 Grade E weldable?

Yes, ASME SA517 Grade E is weldable, but due to its high strength and alloy composition, proper welding procedures must be followed. Preheating may be necessary for thicker sections, and post-weld heat treatment (PWHT) is often recommended to relieve residual stresses and prevent cracking. Careful selection of filler material and welding techniques will ensure strong, reliable welds.

 

 

SA517 grade EChemical Composition

Grade

The Element Max (%)

C

Si

Mn

P

S

SA517 grade E

0.10-0.22

0.08-0.45

0.35-0.78

0.035

0.035

Cr

Mo

B

Ti

 

1.34-2.06

0.36-0.64

0.001-0.005

0.005-0.11

 

 

Grade

 

SA517 grade E Mechanical Property

Thickness

Yield

Tensile

Elongation

SA517 grade E

mm

Min Mpa

Mpa

Min %

6-65

690

795-930

16%

65-150

620

725-930

14%

 

 

1. What is the maximum thickness of SA517 Grade E?

The maximum thickness of ASME SA517 Grade E is generally limited to 6 inches depending on the specific application and welding requirements.

 

2. What is the sulfur content in SA517 Grade E?

The sulfur content in ASME SA517 Grade E is limited to a maximum of 0.035%. Low sulfur content is essential for ensuring that the material remains ductile and free from inclusions that could lead to cracking or weaknesses. This is especially important when the material is subjected to high-pressure conditions or during welding processes.

 

3. What is the phosphorus content in SA517 Grade E?

The phosphorus content in ASME SA517 Grade E is limited to a maximum of 0.035%. Phosphorus can lead to embrittlement, particularly during welding. Keeping phosphorus levels low ensures the material maintains its toughness and strength, especially in applications where high-pressure resistance and mechanical properties are critical.

 

4. What is the composition of carbon in SA517 Grade E?

The carbon content in ASME SA517 Grade E typically ranges from 0.15% to 0.20%. This controlled carbon content ensures the material retains its strength and toughness while maintaining good weldability. Carbon also plays an essential role in the material's overall toughness and resistance to high temperatures, ensuring that the steel performs well under stress and elevated conditions.

 

5. What are the common uses of SA517 Grade E?

ASME SA517 Grade E is used primarily in the manufacturing of pressure vessels, heat exchangers, and boiler components that need to withstand high temperatures and pressures. It is ideal for applications in industries such as power generation, petrochemical processing, and heavy engineering, where strength, toughness, and resistance to elevated temperature conditions are crucial.

 

Contact now

For more details about GNEE's steel products, contact us at info@gneesteels.com. We look forward to working with you.

info-812-678

Send Inquiry

whatsapp

phone

Email

Inquiry