Mar 05, 2024 Leave a message

Heat Treatment of Extruded Mg-12Gd-3Y-0.6Zr Alloy Plate

Clearing Up the Subject: Not a Wear Plate, an Extruded Magnesium Section

The source material approaches the topic as though it were about steel wear plate, yet every parameter in it belongs to a wrought magnesium alloy. Mg-12Gd-3Y-0.6Zr is a heavy-rare-earth magnesium system: 12 percent gadolinium by mass, 3 percent yttrium, 0.6 percent zirconium, balance magnesium. It is produced by ingot metallurgy and hot extrusion, not by hot rolling of a steel slab, and it is specified for weight-critical structural parts rather than for abrasion liners. Buyers should read the designation that way, because the acceptance tests, the temper designations and the property values are all magnesium-specific.

Zirconium at 0.6 percent is not a decorative addition. It acts as a grain refiner in the melt and suppresses grain growth during subsequent thermal exposure, which matters more here than in most magnesium alloys because the whole point of the Gd-Y addition is to allow service at elevated temperature. Gadolinium and yttrium form a high-volume fraction of intermetallic phase on ageing, and that precipitate network is what carries the strength.

Why This System Responds So Strongly to Thermal Treatment

Magnesium has a hexagonal close-packed lattice with limited slip systems at room temperature, so solid-solution and precipitation strengthening do far more work than in steel. In the Mg-Gd-Y system the solubility of gadolinium in magnesium falls sharply as temperature drops, which creates a wide window for solution treatment followed by controlled precipitation. Yttrium behaves similarly and, in combination with gadolinium, produces a denser and more thermally stable precipitate population than either element alone.

The practical consequence is that the same extrusion can show yield strength differences of well over 100 MPa depending on which temper it receives. That is not a marginal effect that a designer can absorb with a safety factor. It means the temper designation must be written into the purchase specification, quoted on the inspection certificate, and verified on the delivered part.

The Three Tempers Defined

Solution treatment, designated T4, holds the section at a temperature high enough to dissolve the soluble eutectic phases and put gadolinium and yttrium into solid solution, then quenches fast enough to retain that supersaturated state. In this alloy the quench is not water at ambient temperature; warm water in the range of 70 to 80 degrees Celsius is used, because a cold quench on a thin extruded wall produces residual stress and distortion severe enough to fail a straightness check, and in the worst case quench cracking.

Artificial ageing, designated T5 when applied directly to the as-extruded product without a prior solution treatment, holds the section at a lower temperature for a defined time so that precipitates nucleate and grow. T6 combines both steps: solution treatment, quench, then artificial ageing. T5 relies on the supersaturation left by the extrusion process itself, since the material leaves the press at a temperature high enough to retain solute in solution, and the subsequent ageing treatment does the rest.

The Starting Condition Sets the Ceiling

The route that produces the billet matters as much as the temper that follows. Industrial practice for this alloy starts from pure magnesium plus master alloys, typically a magnesium-gadolinium master alloy containing roughly 30 percent Gd, a magnesium-yttrium master alloy at roughly 32 percent Y, and a magnesium-zirconium master alloy at roughly 30 percent Zr. Melting is carried out at 730 to 750 degrees Celsius under a protective CO2 and SF6 atmosphere; SF6 is the component that builds a barrier film on the melt surface, and its concentration is a safety and environmental control point rather than an operating convenience.

The cast round billet, commonly 180 mm diameter, is homogenised at about 530 degrees Celsius for 24 hours. Homogenisation is not optional: without it, the cored cast structure retains brittle eutectic networks at grain boundaries that will crack during extrusion. Extrusion follows at approximately 450 degrees Celsius with an extrusion ratio around 16:1, which converts the cast structure into a worked, partially recrystallised structure with a strong fibre texture along the extrusion direction.

Everything downstream is bounded by this history. A billet that was under-homogenised cannot be rescued by a longer ageing time, and an extrusion run too cold leaves a structure that responds inconsistently to solution treatment.

What Each Temper Does to the Microstructure

In the as-extruded condition the structure is a magnesium matrix with coarse undissolved intermetallics aligned in bands along the extrusion direction, plus a partially recrystallised grain structure. Strength is moderate and elongation is limited. Solution treatment at the appropriate temperature dissolves most of the coarse eutectic phase, and the warm-water quench retains a supersaturated solid solution with a grain size largely inherited from the extrusion, since zirconium keeps the grain boundaries pinned.

Ageing then precipitates fine particles throughout the matrix, and hardness and strength climb. The distinction between T5 and T6 in this alloy is subtle but commercially decisive. T6 has more solute available to precipitate because the solution treatment dissolved more of the coarse phase, so its peak ageing response is stronger. But T6 also requires a second high-temperature exposure, and that exposure coarsens the grain structure. Once grains grow, the Hall-Petch contribution falls and the extra precipitate volume no longer compensates.

Property Comparison Across Tempers

The table summarises the direction and rough magnitude of the response reported for extruded plate of this composition. Values are indicative ranges for specification discussion, not guarantees for any particular heat; the certified figures belong on the mill's inspection certificate and must be traceable to the test method used.

Condition Microstructure driver Tensile strength Yield strength Ductility
As-extruded, no temper Coarse intermetallics, partial recrystallisation Lowest of the four Low Moderate
T4, solution only Supersaturated matrix, coarse phase dissolved Moderate Low, soft condition Highest
T5, ageing on as-extruded Fine precipitates, grain size retained High, around 400 MPa class High, around 370 MPa class Retains usable ductility
T6, solution and ageing Denser precipitates but coarsened grains Higher peak ageing response but offset by grain growth Offset in practice Reduced

Why T6 Did Not Win Here

The counter-intuitive result reported for this composition is that T5 delivers better combined properties than T6, despite T6 having the stronger ageing response. The explanation is grain growth during the solution treatment and the associated loss of boundary strengthening, which outweighs the gain in precipitate volume. Tensile strength after T5 falls in the region of 400 MPa with yield around 370 MPa, with ductility sufficient for structural use; the T6 route loses strength and ductility relative to that, driven by the coarser grain structure.

For a buyer the lesson is to reject the assumption that the more complex temper is always the better one. Temper selection has to be tied to section thickness, because a thin extrusion heats and cools faster in solution treatment and coarsens less, while a thick section spends longer at temperature and coarsens more. A schedule qualified on 10 mm wall is not automatically valid on 40 mm.

Specifying and Verifying the Temper

A usable purchase specification for this class of product states four things: the alloy designation and analysis limits referenced to GB/T 5153, the product form and dimensions, the temper designation in full, and the mechanical property minima with the test method. Tensile testing at room temperature is carried out to GB/T 228.1, and test pieces for wrought magnesium products are prepared to GB/T 16865 so that the gauge length and grip arrangement are consistent between supplier and buyer. Hardness is measured to GB/T 4340.1, and for magnesium the load and dwell time must be stated, because the low flow stress of the matrix makes the result sensitive to both.

Chemical verification should be by the methods of the GB/T 13748 series for magnesium and magnesium alloys, with gadolinium, yttrium and zirconium reported individually. Zirconium deserves particular attention, since it is both a grain refiner and a variable that is easy to lose to settling in the melt; a low zirconium result usually shows up as an abnormally coarse grain structure on the macrograph rather than as a chemistry failure on the certificate.

For product form and dimensional tolerances, ASTM B107/B107M is a widely used reference for magnesium alloy extruded bars, rods, shapes and tubes, and is often quoted alongside the GB system when a project requires dual certification. Whichever set is chosen, the certificate should name the edition and the temper, because the same designation can hide different ageing schedules.

Microstructural Acceptance, Not Just Numbers

Two heats can meet the same tensile minima with very different structures, and the difference shows up later as inconsistent machining, dimensional drift after stress relief, or scatter in fatigue results. A metallographic check on a transverse section should confirm a recrystallised matrix with a grain size consistent with the qualified process, a uniform distribution of fine precipitates after ageing, and the absence of continuous coarse eutectic stringers. A macrograph of the full section should show no extrusion defects such as seam, blister or coarse peripheral grain ring.

Porosity and inclusions are best assessed on a polished section or by radiographic methods agreed between the parties, since hydrogen porosity in magnesium is not visible on the surface and is the usual cause of a part that machines cleanly but fails on pressure tightness.

Where These Extrusions Are Used

Mg-Gd-Y-Zr extrusions of this class go into weight-critical structural components: housings and brackets in transport equipment, structural elements in aerospace and unmanned systems, and load-bearing frames in portable or handheld equipment where every kilogram of the finished assembly matters. They are chosen for specific strength at modest temperature, not for abrasion resistance, and the material is normally protected by a conversion coating or anodising because the standard electrode potential of magnesium makes it the anode in contact with almost any other structural metal.

Design practice follows from that: dissimilar metal joints need isolation washers and sealant, threaded fasteners should be inserted with galvanic separation, and drainage paths must be designed in so that water does not pond against the surface. These are not finishing details; they determine service life more than a 10 MPa difference in yield strength does.

Common Misreadings of the Data

The first misreading is to compare an extruded test bar value with a value obtained from a full-section specimen; the two differ because the test bar removes the peripheral grain structure that the real part retains. The second is to treat a single tensile result as the specification; magnesium alloys show measurable scatter, and minima should be supported by a statistically meaningful sample from the qualified process. The third is to assume that ageing time can be extended to gain strength. Past the peak, over-ageing coarsens the precipitates and strength falls, and on a thick section the interior may reach peak later than the surface, so the ageing window is narrower than on thin stock.

The fourth is to ignore residual stress. Warm-water quenching reduces it but does not eliminate it; a part that is machined heavily on one face after heat treatment will move. For close-tolerance components, specify a stress-relief treatment before finish machining and state the allowance explicitly.

FAQ

Q: What is the difference between T5 and T6 for this alloy?
T5 applies artificial ageing directly to the as-extruded product and relies on the supersaturation left by the press; T6 adds a solution treatment and quench before ageing, which dissolves more coarse phase but also exposes the material to an extra high-temperature cycle.

Q: Why is warm water used for the solution quench instead of cold water?
Warm water in the 70 to 80 degrees Celsius range reduces the thermal gradient across the section, which limits residual stress, distortion and the risk of quench cracking in thin extruded walls while still retaining a supersaturated solid solution.

Q: Why can T6 give lower strength than T5 despite stronger ageing?
Because the solution treatment coarsens the grain structure; the loss of grain-boundary strengthening outweighs the additional precipitation, so both strength and ductility fall relative to T5.

Q: Which standard covers the alloy designation and composition?
GB/T 5153 for wrought magnesium and magnesium alloy designations and chemical composition, with analysis carried out by the methods of the GB/T 13748 series.

Q: How should tensile properties be tested?
Room-temperature tensile testing to GB/T 228.1 with specimens prepared to GB/T 16865, and the specimen orientation relative to the extrusion direction stated on the certificate.

Q: What causes a coarse grain structure in a delivered extrusion?
Usually insufficient zirconium in the melt, a homogenisation treatment that was too short or too cool, or an extrusion temperature high enough to allow recrystallised grains to grow after deformation.

Send Inquiry

whatsapp

phone

Email

Inquiry