Sep 18, 2023 Leave a message

Determining Pressure Vessel Class I, II and III Categories

Why Vessels Are Divided Into Three Categories at All

The three category system for fixed pressure vessels is not a quality ranking and not a strength ranking. It is a regulatory consequence ranking, built so that inspection effort is spent where a failure would be most damaging. A category III vessel is not a better made vessel than a category I vessel; it is a vessel whose failure mode, medium and stored energy require more evidence of integrity before it may be placed in service. Buyers who read the category as a durability label routinely overpay for simple equipment and, more dangerously, under-specify the documentation on genuinely hazardous service.

The governing framework in Chinese practice is the fixed pressure vessel safety regulation, which sits above the design code. The regulation defines which vessels fall in scope, sets the category rules, and imposes supervision inspection on defined items. GB 150.1 to 150.4 then supplies the design, material, fabrication and testing mechanics that a vessel of a given category must satisfy. The two documents work in series: the regulation decides how much evidence is required, the code decides what the evidence is.

The Two Inputs: Pressure Band and Medium Group

Category determination combines a mechanical input with a hazard input. The mechanical input is the pressure band already used for vessel classification: low pressure from 0.1 MPa to below 1.6 MPa, medium pressure from 1.6 MPa to below 10 MPa, high pressure from 10 MPa to below 100 MPa, and ultra-high pressure at 100 MPa and above. The hazard input is the medium group, which in the current regulation separates media into a first group and a second group.

The first group covers chemical media with an extreme or high degree of toxicity hazard, explosive media and liquefied gases. The second group covers everything else in scope. Toxicity degree is not judged by smell or by familiarity; it is judged against the occupational exposure hazard grading standard, GB 5044, which places substances into extreme, high, moderate and mild hazard levels using acute toxicity, chronic effects and exposure concentration data together. A buyer who writes only "process medium: solvent" on a data sheet is asking the fabricator to guess the group, and the guess will be the conservative one.

Where the pressure band and the medium group alone do not settle the matter, the stored energy of the vessel is used as the tie-breaker. Stored energy is expressed as the product of pressure and volume, pV, in megapascal cubic metres, and thresholds on that product promote a vessel from a lower category to a higher one for specific combinations of pressure band and medium group. This is why a modest pressure vessel of large volume can be categorised above a small high pressure one.

How Each Category Is Reached in Practice

Category I is the residual case: low pressure vessels that do not meet any of the promoting conditions for category II or III fall here. Category II is reached by promotion, and the promoting conditions include a medium pressure vessel of second group medium, a low pressure vessel holding first group medium at extreme or high toxicity, a low pressure reaction or storage vessel holding flammable or moderately toxic medium, a low pressure shell and tube waste heat boiler, and a low pressure glass-lined vessel. Category III is also reached by promotion and includes any high pressure vessel, a medium pressure vessel holding first group medium at extreme toxicity, and a medium pressure storage vessel holding flammable or moderately hazardous medium once the pV product reaches the threshold set in the classification chart, conventionally 50 MPa.m3 for the relevant combination.

Category Typical pressure band Medium condition Stored energy condition
Category I Low pressure 0.1-1.6 MPa Second group medium, no promoting condition met Below the promoting pV threshold
Category II Medium pressure 1.6-10 MPa Second group medium Below the promoting pV threshold
Category II Low pressure 0.1-1.6 MPa First group medium, extreme or high toxicity; flammable; moderate toxicity in reaction or storage duty; glass-lined; waste heat boiler Any pV within the low pressure band
Category III High pressure 10-100 MPa Any medium group Any pV
Category III Medium pressure 1.6-10 MPa First group medium at extreme toxicity Any pV
Category III Medium pressure 1.6-10 MPa Flammable or moderately hazardous medium in storage duty pV at or above the chart threshold, conventionally 50 MPa.m3

The table summarises the structure rather than replacing the classification chart. The operative rule for a buyer is simpler: obtain a written category determination from the design organisation, with the medium group and the pV value stated explicitly, before the plate is ordered. A category stated only as a sales claim is not a determination.

Distinguishing the Categories by the Evidence They Require

The fastest way to tell which category a vessel belongs to is to look at the inspection and certification package it demands. Category I vessels are normally built with partial volumetric examination of the main seams and a routine material certificate. A category II vessel adds a fuller material traceability chain, mandatory impact testing where the design temperature requires it, a larger proportion of weld examination and, for many items, a design document review by a qualified body. A category III vessel adds full volumetric examination of all main seams, mandatory third-party supervision inspection at defined hold points, complete weld procedure qualification and welder performance records, and a documentation set that will be audited rather than filed.

This progression is visible in the joint efficiency used in the thickness calculation. Under GB 150.3 a fully examined double-welded butt joint carries an efficiency of 1.00, a partially examined joint carries 0.85 and an unexamined joint carries 0.70. Because a category III vessel is examined over the full length of its main seams, it can be designed closer to the allowable stress than a category I vessel of identical pressure. The higher category therefore sometimes produces a thinner shell, not a thicker one, which is the opposite of what buyers expect.

What Changes in the Purchase Specification

Once the category is known, five specification items become non-negotiable and should be written into the order rather than negotiated after award.

Material certification: the mill certificate must identify heat number, product analysis, tensile properties at the ordered thickness, impact energy at the specified test temperature, and the delivered heat treatment condition. A certificate that reports properties from a thinner reference thickness is not evidence for the plate supplied.

Weld qualification: procedure qualification and welder performance qualification must cover the actual thickness range, the actual welding process and the actual material group being joined, with the qualification records available for review.

Examination scope: the percentage of radiographic or ultrasonic examination, the acceptance level and the treatment of repairs must be fixed in the specification, together with the requirement that repair areas are re-examined by the same method.

Heat treatment: post-weld heat treatment is triggered by thickness, by material group and by service environment, and the specification must state the holding temperature range, the holding time basis and the cooling rate rather than leaving it to shop practice.

Supervision inspection: hold points, notification periods and the documents required at each point must be agreed before fabrication starts, because a supervision body that is notified late cannot retrospectively witness a closed seam.

Material and Thickness Choices That Follow From the Category

Category I and II vessels in second group medium are usually built from Q245R or Q345R to GB/T 713. Q245R offers a tensile strength range of about 400 to 520 MPa with a minimum yield of 245 MPa and is the economical choice for low pressure shells where the corrosion allowance dominates the thickness. Q345R raises the minimum yield to 345 MPa and the tensile range to about 510 to 640 MPa, allowing thinner shells at medium pressure, at the cost of tighter weld control because the higher carbon equivalent increases hardenability and cold cracking risk.

Requirement Category I Category II Category III
Main seam volumetric examination Partial, per design specification Increased proportion, per design specification Full length of all main seams
Impact testing Where design metal temperature requires Required at the specified test temperature Required, with results on the mill certificate
Weld procedure qualification Required, covering the thickness range Required, reviewed with the design file Required, audited with welder records
Post-weld heat treatment By thickness and material rule By thickness, material and service rule Commonly mandatory, documented in full
Supervision inspection Generally not applied Applied to defined items Applied with defined hold points throughout
Hydrostatic test 1.25 times design pressure, stress corrected Same basis Same basis, with full record retention

Where the design metal temperature falls to -40 C, the carbon steel grade is replaced by a low temperature grade such as 16MnDR to GB/T 3531, which combines a tensile range of about 490 to 620 MPa with impact toughness verified at the low temperature. Where the design temperature rises into the creep range, a Cr-Mo plate such as 15CrMoR to GB/T 713 or SA387 Gr.11 or Gr.22 to ASME BPVC Section II Part A takes over, and the post-weld heat treatment becomes a mandatory step rather than a thickness-driven one.

Misclassification Risks and How to Avoid Them

The first risk is using operating pressure in place of design pressure. Operating pressure is what the gauge reads; design pressure is the upper bound the calculation uses and is normally set above the highest expected operating pressure with margin for control deviation. A vessel categorised on operating pressure is systematically under-categorised.

The second risk is describing the medium by trade name. A trade name does not map to a hazard group, and the fabricator cannot verify toxicity or flammability from it. Provide the chemical identification and, where relevant, the safety data sheet extract that establishes the hazard classification.

The third risk is ignoring the pV product for large low pressure storage. A large atmospheric-adjacent tank holding a flammable liquid can sit close to a promoting threshold, and a small change in working volume during detailed design moves it across that threshold. Fix the volume from the final general arrangement drawing, not from a preliminary sketch.

The fourth risk is assuming that a higher category requires a thicker shell. As noted above, the fuller examination credited in a higher category raises joint efficiency and can reduce required thickness. Specifying both a category III examination scope and a conservatively thickened shell is not wrong, but the buyer should know the thickness premium is being paid voluntarily.

Verifying a Category Determination Before Award

A defensible determination is a one page document that states the design pressure, the design temperature, the minimum design metal temperature, the geometric volume, the medium identification and hazard group, the calculated pV product, the resulting category and the classification chart clause relied upon. Ask for it with the technical proposal. Then check three consistency points: that the pV product is calculated from the stated volume and design pressure rather than from nominal capacity; that the hazard group matches the safety data sheet rather than a generic description; and that the examination and heat treatment requirements quoted in the proposal match the requirements the stated category implies. Any mismatch is a commercial risk that will surface either as an inspection finding at the fabricator or as a rejected registration at the point of installation.

FAQ

Q: What makes a pressure vessel category III rather than category II?
The most common triggers are any high pressure vessel, a medium pressure vessel holding a first group medium of extreme toxicity, and a medium pressure storage vessel holding flammable medium once the pressure-volume product reaches the classification chart threshold.

Q: Is the category based on working pressure or design pressure?
It is based on design pressure, the maximum pressure at the top of the vessel in its normal operating position at the coincident design temperature. Operating pressure and relief valve set pressure are not substitutes.

Q: How is the hazard group of a medium established?
By identifying the chemical and grading it against the occupational exposure hazard standard, GB 5044, which sorts substances into extreme, high, moderate and mild hazard levels. Explosive media and liquefied gases are treated as first group regardless of toxicity.

Q: What is pV and why does it decide categories?
pV is the product of design pressure in megapascals and geometric volume in cubic metres, and it is a proxy for stored energy. Above a defined pV threshold, a failure releases enough energy to promote a vessel into a higher category even at moderate pressure.

Q: Does a higher category mean a thicker shell?
Usually not. Higher categories require fuller volumetric examination, which earns a joint efficiency of 1.00 instead of 0.85 or 0.70, so the calculated thickness at a given pressure can be lower. Thickness is governed by pressure, corrosion allowance and temperature, not by category.

Q: Which steel plate grades are typical for category II and III vessels?
Q245R and Q345R to GB/T 713 cover most carbon steel shells up to moderate temperature, 16MnDR to GB/T 3531 covers service down to -40 C, and 15CrMoR to GB/T 713 or SA387 Gr.11 and Gr.22 to ASME BPVC Section II Part A cover elevated temperature service.

Q: Can the category be changed after fabrication has started?
Rarely without cost. A change upward alters the examination scope, the heat treatment requirement and the supervision inspection hold points, and hold points already passed cannot be witnessed retrospectively. The category must be fixed before plate cutting.

Send Inquiry

whatsapp

phone

Email

Inquiry