What the EH32 Designation Actually Tells a Buyer
EH32 is one of the four higher-strength hull structural steel grades defined by the unified classification-society framework for shipbuilding, and it sits in the 315 MPa yield family that also includes AH32, DH32 and FH32. The letter denotes the impact-testing temperature band: A is tested at 0 °C, D at -20 °C, E at -40 °C and F at -60 °C. The number 32 denotes the nominal minimum yield strength in kilograms-force per square millimetre, which converts to 315 MPa. EH32 therefore combines a 315 MPa minimum yield with a Charpy impact test performed at -40 °C, and that combination is what separates it from DH32 and from ordinary 355 MPa structural plate such as S355J2 or Q355D.
The distinction matters commercially because EH32 is not a single national grade but a rule-defined grade. The same plate may be ordered against ASTM A131/A131M as grade EH32, against the IACS Unified Requirement W11 tables used by every member classification society, against EN 10225 for offshore structures, or against GB/T 712 for hull structural steel, and the buyer's approval authority will normally state which of these applies. Mechanical property limits are aligned across these documents, but chemistry limits, thickness ranges, tolerancing and the form of the mill certificate are not identical. A purchase order that names only "EH32" without naming the rule set and the certifying society leaves the mill free to interpret survey requirements, and that is where most delivery disputes begin.
Because EH32 is an impact-qualified grade, it is normally supplied killed and fine-grain treated, with aluminum or niobium-titanium additions controlling austenitic grain size. Coarse-grain practice can pass a tensile test and still fail the -40 °C Charpy requirement, so grain-refining practice is a quality issue rather than a metallurgical nicety.
Chemical Composition and Fine-Grain Practice
Classification rules for higher-strength grades of the 32 and 36 families set upper limits rather than fixed ranges, because the steelmaker is allowed to reach the mechanical properties by as-rolled, normalized, or thermo-mechanical controlled processing routes. The limits below reflect the values that appear in the common rule tables for grade EH32 plate and are the limits a buyer should expect to see on the mill certificate.
Carbon is capped at 0.18% for the higher-strength 32 grade in most rule sets, and many mills run 0.10-0.14% to protect toughness and weldability. Manganese is the main strengthener and is specified in a range of roughly 0.90-1.60%, with the upper half of that range used for as-rolled and TMCP plate. Silicon is held to 0.10-0.50% for deoxidation, phosphorus and sulphur are each limited to 0.035% maximum, and aluminium is required at 0.015% minimum on the acid-soluble basis when the steel is aluminium-killed and required to be fine-grained. Residual elements are tightly constrained: copper 0.35% maximum, chromium 0.20% maximum, nickel 0.40% maximum, molybdenum 0.08% maximum, and nitrogen 0.009% maximum unless a nitrogen-binding addition such as titanium or vanadium is present. Micro-alloying additions are limited collectively, typically niobium plus vanadium plus titanium at 0.12% maximum, which is enough to deliver grain refinement through TMCP but not enough to create hard, crack-sensitive zones in the heat-affected weld.
Carbon equivalent is the single number most often used at the fabrication yard to decide preheat. On the IIW basis, EH32 is normally ordered to a maximum carbon equivalent of 0.40% for plate up to about 50 mm, and 0.38% or lower is readily achieved by killed, fine-grain practice. Some offshore specifications add a crack-susceptibility parameter limit as well, typically 0.24% maximum for Pcm, which controls the hardenability of the heat-affected zone more accurately than carbon equivalent alone on lean-composition TMCP plate.
Mechanical Properties and the -40 °C Impact Requirement
Tensile properties for EH32 are specified on the full-thickness rectangular specimen, with the yield strength taken as the 0.2% proof stress or the upper yield point, whichever is relevant to the product. The tensile range is deliberately banded, because a plate that is too strong is as much a fabrication risk as one that is too weak: over-strength plate raises heat-affected-zone hardness, increases restraint stresses in thick weld joints, and can shift brittle fracture behaviour under dynamic loading.
| Property | EH32 requirement (typical rule values) | Test method |
|---|---|---|
| Yield strength, minimum | 315 MPa (45,700 psi) | Tensile test, ASTM A370 / ISO 6892-1 |
| Tensile strength | 440-590 MPa | Tensile test, full-thickness specimen |
| Elongation, minimum | 22% on 50 mm gauge length | Tensile test |
| Charpy V-notch, transverse | 31 J average at -40 °C, single value not below 70% of the average | ISO 148-1 / ASTM A370, three specimens |
| Charpy V-notch, heavier sections | Higher energy levels commonly apply above 50 mm | Same, with sub-size or full-size specimens as ruled |
| Carbon equivalent (IIW) | 0.40% maximum typical, 0.38% achievable | Ladle analysis calculation |
| Grain size | Fine grain, typically ASTM 7 or finer | Micrographic examination |
The impact test is where EH32 earns its price premium over DH32. Three specimens are cut transverse to the rolling direction, notched perpendicular to the plate surface, and broken at -40 °C. Acceptance is based on the average of the three values plus a floor on individual results, and the test temperature is the specified temperature of the grade, not an arbitrary cold-room setting. For thicknesses where a full-size 10 mm by 10 mm specimen cannot be extracted, sub-size specimens are used and the acceptance energy is scaled by the rule table, so a 31 J figure quoted for a 60 mm plate is not directly comparable with a 31 J figure for a 20 mm plate tested on a full-size specimen.
Shear-area examination is required in parallel with absorbed energy in most rule sets. A specimen can absorb the required joules while showing a high proportion of brittle cleavage fracture, and surveyors routinely reject results where the fibrous appearance falls below the rule minimum even though the energy value passes. This is one reason why impact testing of EH32 is duplicated at the plate mill and again, where the specification requires it, at an independent laboratory.
Delivery Condition, Thickness Range and Tolerances
EH32 plate is produced in three conditions. As-rolled plus controlled rolling is used for the thinner end of the range and for non-critical internal structure. Normalized plate, or normalized plus tempering where the mill's practice requires it, is used when the specification demands a uniform ferrite-pearlite structure independent of section size. Thermo-mechanical controlled processing, with accelerated cooling, is the dominant route for higher-strength hull plate today because it delivers the 315 MPa yield with leaner chemistry and better toughness at the same carbon equivalent.
The delivery condition must be stated on the order, because the same grade designation can be satisfied by any of the three routes, and a yard that has qualified its welding procedure on TMCP plate may not be able to use normalized plate on the same procedure without requalification. Repairs involving local normalizing after fabrication are also restricted: TMCP plate loses part of its strength and toughness benefit if it is heated above the tempering range of the thermo-mechanical schedule, and most classification rules limit such heating or require re-testing.
Thickness tolerances for hull plate are usually ordered to a restricted negative tolerance so that the actual scantling is never below the designed value. Normal mill tolerance under the general dimensional standard permits a negative deviation at the nominal thickness; hull specifications commonly call for zero negative tolerance or a tolerance class in which the minus side is eliminated. Flatness is equally important: plates are cut and assembled by automatic profile cutting and robot welding, and out-of-flatness beyond the rule limit forces re-straightening, which introduces residual stress and can degrade toughness in the surface layer.
Surface quality is governed by the applicable surface-condition standard for hot-rolled plate. Seams, laps, shells and scratches are classified by depth and are either accepted, ground out, or rejected, and the total ground area per unit of plate surface is capped. For EH32 used in hull envelope plating, weld repairs of surface defects require the surveyor's agreement and a qualified repair procedure, since an uncontrolled repair weld in a 315 MPa impact-qualified steel can create a local hard zone that behaves worse than the original defect.
Welding EH32: Consumables, Heat Input and Preheat
EH32 is welded with the same processes used for ordinary hull steel: shielded metal arc, gas metal arc, flux-cored arc with either rutile or basic slag, and submerged arc for long straight seams and panel lines. Consumables are selected on strength matching plus toughness matching. For a 315 MPa minimum yield parent metal with a -40 °C impact requirement, the consumable deposit must itself be qualified at the lowest design service temperature of the joint, which for a hull in a northern trade may be well below the plate test temperature. A common practical rule is to use a consumable classified at a toughness level one grade better than the plate, so that the weld metal, rather than the plate, does not become the limiting element of the joint.
Heat input control is the second lever. Excessive heat input coarsens the heat-affected zone and lowers its Charpy energy, while very low heat input raises cooling rate and hardness. Classification rules and yard welding procedure specifications therefore set both a maximum energy input per unit length and, for higher-strength steels, a minimum preheat and interpass temperature. Typical practice for EH32 in thicknesses up to about 25 mm is a preheat of 50-75 °C with an interpass ceiling of 200-250 °C; above 30-35 mm, or where carbon equivalent is at the top of the permitted range, preheat is raised to 100 °C or above and the procedure is qualified by a hardness survey of the heat-affected zone, usually with a 350 HV10 ceiling for non-stress-relieved joints.
Hydrogen control is mandatory rather than optional. Basic-coated electrodes are baked and held in heated quivers, flux for submerged arc is dried to the manufacturer's schedule, and FCAW wires are stored dry, because diffusible hydrogen above roughly 5 ml per 100 g of deposited metal in a restrained thick joint is a recognised route to delayed cracking in the heat-affected zone of higher-strength hull steel.
Butt joints in hull envelope plating are normally full-penetration, with ceramic backing or back-gouging to sound metal. Tack welds are treated as part of the finished weld and must be made with the same consumable and preheat. Where the design calls for fillet welds at brackets and stiffener connections, the fatigue detail category governs the weld profile, and grinding or TIG dressing of the toe is used where the detail is classified as a fatigue-critical connection.
Cutting, Forming and Dimensional Control
EH32 is cut by plasma, oxy-fuel or laser. Oxy-fuel cutting leaves a heat-affected zone with a hardened edge, and for thick plate that edge is either machined off or the cut face is inspected for hardness and cracking before welding. Plasma cutting is faster and gives a narrower heat-affected zone but produces a nitrided layer on the cut face in some conditions, which must be removed before welding if the procedure specification requires it. Plate edges that will receive full-penetration welds are usually prepared with a machine bevel, and the bevel angle and root face are controlled to the welding procedure rather than to the cutter operator's judgment.
Cold forming of EH32 is limited by the minimum bend radius that the rule set allows for the grade and thickness. Tight bends in the 315 MPa family require larger radii than for normal-strength grade A plate, and bends that approach the limit should be formed transverse to the rolling direction where possible, with the bend line away from the plate edges to avoid edge cracking. After cold forming, the strained region is inspected for surface cracking, and heavily strained areas are often stress-relieved or at least subjected to a hardness check.
Dimensional control starts at the nesting stage. Plate thickness is verified at the mill certificate and again on receipt, because scantling calculations, weld procedure qualification and lifting plans all assume the ordered thickness. Camber, length and width deviations beyond the applicable dimensional standard are grounds for rejection regardless of mechanical test results, since an out-of-tolerance plate cannot be nested without excessive scrap.
Inspection, Certification and Mill Documentation
Every plate of EH32 intended for a classed vessel is surveyed. The survey covers the steelmaking route, the heat treatment or TMCP schedule, the test sampling position, and the test results, and it results in a certificate issued under the classification society's rules rather than a plain mill certificate. The certificate identifies the society, the grade, the heat number, the plate number, the dimensions, the delivery condition, the chemical composition on ladle and product analysis, and the tensile and impact results with the test temperatures stated explicitly.
Where the buyer's project specification calls for it, plates are also supplied with an inspection certificate to a general product-certificate standard at the 3.1 or 3.2 level, which shifts the inspection responsibility from the manufacturer's own authority to an independent inspector or the purchaser's representative. For hull plate ordering, the two documents are complementary, not alternatives: the class certificate satisfies the statutory survey, and the product certificate satisfies the contractual quality clause.
Non-destructive testing is ordered by designation. Ultrasonic examination of plate is specified by acceptance class, and the class must be written on the order because the same plate can pass a general laminar-discontinuity class and fail a stricter class intended for hull envelope plating or for areas subject to through-thickness stress. Where the design has welded connections that load the plate through its thickness, Z-direction quality is specified separately, and the through-thickness tensile test results appear on the certificate as a distinct item.
Purchase Order Checklist for EH32 Plate
An unambiguous order removes most of the commercial risk. The essential items are: grade EH32 with the governing rule set named, the certifying classification society, the delivery condition, the thickness range with the required dimensional tolerance class, the impact test temperature and energy explicitly restated, the ultrasonic acceptance class, the surface condition standard, the certificate form, and the Z-direction requirement where applicable.
Beyond the order itself, three verification steps protect the buyer. First, compare the ladle analysis on the certificate with the product analysis; a large positive drift in carbon or sulphur indicates segregation or a heat that was adjusted after tapping. Second, confirm that the impact specimens were taken from the specified position and orientation, since longitudinal specimens at quarter thickness can pass comfortably where transverse specimens near the surface would not. Third, keep the plate identification intact through fabrication: hard stamping or paint marking that survives blasting is the only way to trace a plate back to its certificate after it has been cut into twenty pieces.
Price differences between apparently identical EH32 offers usually trace back to one of four variables: delivery condition, carbon equivalent and residual control, ultrasonic acceptance class, and whether the certificate is issued under survey or as a plain mill document. Each of these changes the mill's cost and the fabrication risk, so a quotation comparison that ignores them is not a like-for-like comparison.
FAQ
Q: What is the minimum yield strength of EH32 shipbuilding steel plate?
EH32 is specified at a minimum yield strength of 315 MPa, equivalent to 45,700 psi, with a tensile strength band of 440-590 MPa and a minimum elongation of 22% on a 50 mm gauge length.
Q: At what temperature is EH32 impact tested?
The letter E in EH32 sets the Charpy test temperature at -40 °C, with a typical acceptance level of 31 J average on transverse specimens and no single value below 70% of that average for plate up to 50 mm.
Q: Is EH32 the same as DH32?
No. Both are 315 MPa higher-strength grades with the same tensile band, but DH32 is impact tested at -20 °C while EH32 is tested at -40 °C, so EH32 is specified where the design service temperature or the rule requirement is colder.
Q: What carbon equivalent should be expected on an EH32 mill certificate?
A maximum of about 0.40% on the IIW basis is typical for plate up to 50 mm, and lean TMCP practice commonly delivers 0.36-0.38%, which directly reduces the preheat needed at the fabrication yard.
Q: Can EH32 be welded without preheat?
Only in thin sections with low carbon equivalent and a qualified procedure. Above roughly 30 mm, or where carbon equivalent approaches the permitted maximum, preheat of 100 °C or more is normally required, together with a hardness check of the heat-affected zone.
Q: Does a mill test certificate prove the plate is class approved?
Not by itself. A class-approved plate carries a certificate issued under the classification society's survey, which is a separate document from a general inspection certificate at the 3.1 or 3.2 level, and both may be required by the project specification.




