Cold rolled steel coil is produced by cold reducing hot rolled pickled strip at room temperature, then annealing and temper rolling it to the final thickness, flatness and surface finish. Because it is formed below the recrystallisation temperature, the coil offers tight thickness tolerances, a smooth surface and consistent mechanical properties, which is why it is the starting material for coated sheet, tubes, panels and a very wide range of manufactured goods. This article covers the production route, the grades and sizes in highest demand, and the coating options that follow.
What Cold Rolled Steel Coil Is
The product is a continuous coil of low carbon or high strength low alloy steel, supplied in widths from roughly 600 mm to 1550 mm and thicknesses from 0.30 mm to 3.0 mm. Two features distinguish it from hot rolled coil:
Dimensional accuracy: cold reduction plus a temper pass gives a consistent thickness across and along the strip, which matters for forming and for coating adhesion.
Surface quality: the strip can be supplied with a controlled surface finish, from matt to bright, with a defined oil film that protects against corrosion and reduces degreasing cost at the user works.
Production Route
Pickling: hot rolled coil is descaled in acid to remove oxide, then oiled or pre-oiled.
Cold reduction: tandem or reversing mills roll the strip to final thickness, typically achieving a total reduction of 50 to 80 %.
Annealing: batch annealing in a bell furnace or continuous annealing in a line restores ductility and controls the final grain structure.
Temper rolling: a light 0.5 to 2 % reduction sets flatness, surface texture and yield point, and prevents stretcher strain during forming.
Finishing: slitting, edge trimming, oiling, inspection and packing according to the agreed surface and tolerance class.
Grades in High Demand
| Standard | Grades | Typical use |
|---|---|---|
| EN 10130 | DC01, DC02, DC03, DC04, DC05, DC06 | Low carbon cold forming grades, from general fabrication to deep drawing |
| EN 10268 | HC260LA to HC500LA | High strength low alloy grades for weight reduction |
| ASTM A1008 / A1008M | Commercial steel, drawing steel, structural steel and high strength low alloy groups | North American ordering basis for cold rolled sheet |
| EN 10131 | Dimensional tolerance class | Thickness, width and flatness tolerances for uncoated cold rolled product |
As the grade number rises from DC01 to DC06, formability improves and the material is used for progressively deeper drawn parts. High strength low alloy grades such as HC260LA and HC340LA are increasingly specified because they cut the weight of a structure while maintaining or raising its load bearing capacity.
Sizes and Tolerances in High Demand
| Parameter | Typical range |
|---|---|
| Thickness | 0.30-2.0 mm, with 1.0-2.0 mm most often ordered |
| Width | 600-1550 mm, commonly 1000-1500 mm |
| Inner diameter | 508 +/- 10 mm or 610 +/- 10 mm |
| Coil weight | 10-25 t, up to 25 t for continuous processing lines |
| Thickness tolerance | To EN 10131, normal or special (half normal) class |
| Delivery condition | Cold hardened, annealed, or annealed and temper rolled |
Buyers of construction sections and tubes ask for the tightest positive and negative thickness tolerances the standard allows, because a saving of a few hundredths of a millimetre on a formed part is significant over a long production run. Flatness and minimum crown are equally important where the strip feeds a coating line.
Coated and Painted Products
Most cold rolled coil produced worldwide is consumed by a further coating step. Two coating families dominate:
Metallic coatings applied by continuous hot dip or electroplating: zinc, zinc-aluminium, aluminium-zinc, aluminium-silicon and tin coatings. Galvanised product to EN 10346 is the largest single category.
Paint coatings applied by continuous coil coating: polyester, polyurethane, plastisol and related systems, giving colour, texture and additional barrier protection.
For coating lines the critical incoming properties are tight thickness tolerance, minimum crown and a surface that is clean and free of oil defects, because residual oil or dirt causes bare spots, pin-holes and coating flaking. A controlled oil film is normally beneficial; an excessive or uneven film is not.
Applications by Industry
Construction: tubes, closed sections, facade panels, purlins, roof and wall cladding.
Automotive: body panels, structural reinforcements, seat frames and brackets.
Appliances and white goods: outer panels, liners and housings, usually in the coated condition.
Machine building and general manufacture: guards, enclosures, cabinets, shelving and formed components.
Coil coating and packaging: painted strip, tinplate and container stock.
Quality Control
Chemical composition and mechanical properties verified by mill certificate and by tensile test to EN ISO 6892-1.
Hardness and r-value or n-value testing for the deep drawing grades.
Thickness, width and flatness measured through the line and reported against EN 10131.
Surface inspection for slivers, scratches, roll marks and edge defects, plus oil film and roughness checks.
Coating mass and adhesion testing on coated product to the applicable coating standard.
Coils are normally delivered eye to the sky or eye to the wall, wrapped with moisture barrier paper and protected by edge rings, so that handling damage and white rust in transit are avoided.
FAQ
Q: What is the difference between hot rolled and cold rolled steel coil?
Cold rolled coil is cold reduced below the recrystallisation temperature, then annealed. It therefore has tighter thickness tolerances, a better surface and higher formability, but it is limited to thinner gauges than hot rolled product.
Q: Which grade should be selected for deep drawing?
DC03, DC04 and finer drawing grades such as DC05 or DC06 are used as drawing severity increases. DC01 and DC02 are intended for bending and simple forming rather than deep drawn parts.
Q: Why is a temper pass needed after annealing?
Annealed strip is soft and can develop a yield point elongation that causes stretcher strain lines during forming. A light temper rolling pass of 0.5 to 2 % sets the yield point and also delivers the required surface roughness and flatness.
Q: What does the oil film on the coil do?
It provides temporary corrosion protection in transit and storage and acts as a forming lubricant. Most customers ask for a minimum, uniform film so that degreasing cost and cleaning problems at the coating line are reduced.
Q: Why do coating lines specify minimum crown and tight tolerances?
Because the coating must be applied at even thickness along and across the strip. Thickness variation or excessive crown causes uneven coating weight, poor adhesion and visible defects on the finished product.
Q: How should cold rolled coil be stored?
Keep it dry, off the floor, in a ventilated area and away from condensation cycles. Damp storage on unprotected steel is the usual cause of white rust and edge staining on galvanised or bare cold rolled coils.




