What SAE 1050 Is and Where the Grade Sits in the Carbon Steel Family
SAE 1050 is a plain carbon, fully killed medium carbon steel defined by the four-digit numbering system maintained in SAE J403, where the "10" prefix identifies a non-resulphurised carbon steel and the "50" suffix indicates a nominal carbon content of 0.50%. In the unified numbering system the grade is designated UNS G10500. Because it carries no deliberate additions of chromium, nickel, molybdenum or vanadium, SAE 1050 relies entirely on carbon and manganese for hardenability, which makes its mechanical response highly predictable but also limits the maximum section that can be through-hardened. Buyers comparing quotations for "1050 plate" are frequently comparing three different products: hot rolled plate in the as-rolled or normalised condition, cold rolled strip, and quenched and tempered plate. Each has a different property envelope and a different price base, so the delivery condition must be stated before price can be judged.
The grade sits at the upper end of the medium carbon band. Below it, grades such as SAE 1040 and SAE 1045 are easier to weld and machine but cannot reach the same hardness after quenching; above it, SAE 1060 and SAE 1070 gain hardness at the cost of ductility, weldability and machinability. SAE 1050 is therefore the practical compromise grade for parts that must be machined in the soft condition, then hardened and tempered to carry load. In plate form it is supplied most often between 3 mm and 100 mm, with the 6 mm to 40 mm band representing the bulk of commercial tonnage.
Chemical Composition and Cross-Standard Equivalents
The composition limits below follow SAE J403 and the corresponding product standards used in other regions. Values are heat analysis limits; product analysis tolerances apply at the edges of the ladle range and are governed by the applicable standard's tolerance table.
| Element | SAE 1050 / UNS G10500 (SAE J403) | C50E (EN 10083-2) | S50C (JIS G 4051) | 50 (GB/T 699) |
|---|---|---|---|---|
| Carbon, % | 0.48 - 0.55 | 0.47 - 0.55 | 0.47 - 0.53 | 0.47 - 0.55 |
| Manganese, % | 0.60 - 0.90 | 0.60 - 0.90 | 0.60 - 0.90 | 0.50 - 0.80 |
| Silicon, % | 0.10 - 0.30 | 0.40 max | 0.15 - 0.35 | 0.17 - 0.37 |
| Phosphorus, % max | 0.030 | 0.030 | 0.030 | 0.035 |
| Sulphur, % max | 0.050 | 0.035 | 0.035 | 0.035 |
| Copper, % max | 0.20 residual | 0.40 residual | 0.30 residual | 0.25 residual |
Two details matter in practice. First, SAE 1050 is not a fine-grain steel by specification: aluminium or niobium additions for grain control are optional, and a mill may supply it either way. A buyer who needs guaranteed austenitic grain size should request it explicitly and expect a hardenability or grain size report. Second, the sulphur limit of 0.050% for the SAE grade is looser than the 0.035% typical of the European and Japanese equivalents, which is why some SAE 1050 heats machine slightly better but show lower transverse impact energy. When the drawing calls for a European or Japanese equivalent, ordering to C50E or S50C narrows the composition window and usually improves consistency from lot to lot.
Mechanical Properties in the As-Supplied Conditions
SAE 1050 has no single set of mechanical properties: the values depend on whether the plate is hot rolled, normalised, cold drawn or quenched and tempered, and on the thickness at which the test coupon was taken. The table gives the ranges normally quoted in mill test certificates and handbooks for plate and bar product. They are typical values for guidance, not acceptance criteria; acceptance must always be tied to the tensile test position and direction specified in the purchase order.
| Condition | Tensile strength, MPa | Yield strength (0.2%), MPa | Elongation in 50 mm, % min | Hardness | Typical use |
|---|---|---|---|---|---|
| Hot rolled, as supplied | 620 - 750 | 330 - 400 | 12 - 18 | 180 - 220 HB | Blanks for later machining and hardening |
| Annealed | 560 - 660 | 280 - 350 | 18 - 22 | 170 - 200 HB | Heavy machining, cold forming |
| Normalised | 680 - 780 | 360 - 430 | 12 - 17 | 190 - 230 HB | Structural parts, shafts, gears |
| Quenched and tempered, 200 C | 1050 - 1250 | 850 - 1000 | 8 - 12 | 32 - 38 HRC | Wear parts, blades, pins |
| Quenched and tempered, 400 C | 850 - 1000 | 700 - 850 | 12 - 16 | 26 - 32 HRC | Loaded shafts, connecting parts |
| Quenched and tempered, 550 C | 700 - 820 | 550 - 680 | 16 - 20 | 20 - 26 HRC | Parts needing toughness with strength |
The hardenability of SAE 1050 is modest. Ideal critical diameter is roughly 25 mm to 35 mm in water quenching and considerably less in oil, so plate thicker than about 25 mm will not harden uniformly through the section. A hardness traverse across the thickness is the only reliable way to confirm that the core reached the specified level. Where a through-hardened section above 30 mm is required, the correct engineering answer is to move to a low-alloy grade such as 4140 or 42CrMo rather than to increase the austenitising temperature, which only coarsens the grain and raises the risk of quench cracking.
Plate Rolling, Thickness Range and Dimensional Tolerances
SAE 1050 plate is produced either by rolling from continuously cast slab on a plate mill or, for thinner sections, by rolling on a narrow strip mill and shearing to length. Thickness tolerance for hot rolled carbon plate is normally ordered to the tables of ASTM A6/A6M or to EN 10029 class A, and the choice changes the permissible minus deviation substantially. On a 20 mm plate, EN 10029 class A permits a minus deviation of 0.6 mm for widths up to 2000 mm, whereas looser mill tolerances can reach 1.0 mm or more. Because SAE 1050 is frequently used for machined parts, thickness deviation translates directly into machining allowance and scrap, so it is worth specifying explicitly.
Flatness is the second dimensional characteristic that causes claims. Plate cut from coiled strip tends to carry residual curl, and plate rolled from slab can carry centre buckle after accelerated cooling. A flatness requirement expressed in millimetres per metre, measured on a flat table with the plate free of restraint, is far more enforceable than a description such as "good flatness". Edges should be specified as sheared, mill edge or flame cut, with the understanding that flame cutting introduces a heat affected zone of roughly 2 mm to 5 mm that must be removed before finish machining on precision parts. Surface condition should be stated as rolled, pickled or descaled; for SAE 1050, scale left in place is hard and abrasive and accelerates tool wear during the first machining pass.
Heat Treatment Practice: Annealing, Normalising, Austenitising and Tempering
Full annealing is carried out by heating to approximately 790 C to 810 C, holding long enough for the section to be uniformly austenitised (roughly one hour per 25 mm of thickness after the furnace charge reaches temperature), then cooling in the furnace at a controlled rate of about 20 C per hour down to 600 C before air cooling. The result is a coarse lamellar pearlite in a ferrite matrix with hardness around 170 HB to 200 HB, which is the softest and most machineable condition.
Normalising uses a higher temperature, typically 830 C to 870 C, followed by still-air cooling. It refines the grain structure after hot working and produces a more uniform pearlite distribution than the as-rolled condition, at hardness near 200 HB. Where a part will be machined and then quenched, normalising before machining reduces distortion after the final hardening step because the structure is more homogeneous.
Austenitising for hardening is carried out at approximately 800 C to 830 C, at the upper end of the range for thicker sections and the lower end for thin plate and for parts with sharp section changes. Quenching is normally in water or a fast polymer quenchant; oil is used only for sections thinner than about 10 mm or for parts with severe section transitions, because the critical cooling rate of a 0.50% carbon steel is high. The martensite start temperature is around 300 C to 320 C, so parts should be quenched to just below that range and tempered immediately. A delay of more than a few hours between quenching and tempering leaves a crack-sensitive structure, and plate sections above 25 mm have been known to self-crack overnight.
Tempering covers a wide range depending on the target hardness. At 150 C to 200 C the part retains high hardness for wear resistance but low toughness; between 300 C and 400 C there is a temper embrittlement trough for this carbon level that should be avoided where impact loading is expected; above 500 C the structure is tough but hardness falls below roughly 28 HRC. Holding at temperature for one hour per 25 mm of section, with a minimum of one hour, is the usual rule. Slow cooling after tempering is preferred for thick sections to limit residual stress.
Fabrication: Machining, Welding and Forming Notes
In the annealed or normalised condition SAE 1050 machines reasonably well with carbide tooling at surface speeds of about 120 m/min to 180 m/min, using positive rake geometry and generous coolant. In the quenched and tempered condition above 30 HRC, machining should be finished before hardening wherever the geometry allows; otherwise CBN or ceramic inserts and reduced depth of cut are required. Drilling deep holes in the hardened condition is impractical and should be designed out at the drawing stage.
Welding SAE 1050 requires care. With 0.50% carbon, the heat affected zone can transform to untempered martensite and crack, particularly in sections above 12 mm. Acceptable practice is to preheat to 200 C to 250 C, use a low-hydrogen consumable, keep heat input moderate, and perform a post-weld temper at 600 C to 650 C followed by slow cooling. Even then, the joint will not match the strength of the parent plate without a subsequent quench and temper of the whole assembly, which is rarely practical. For fabricated structures, a lower carbon grade such as SAE 1020 or a low-alloy grade is almost always the better choice; SAE 1050 is best reserved for parts that are machined and heat treated as a unit.
Cold forming is limited. SAE 1050 in the annealed condition can be bent to a minimum inside radius of roughly one to one and a half times the thickness in the rolling direction, but transverse bends require a larger radius. Blanking and shearing are feasible up to about 8 mm with adequate press capacity, though the sheared edge work hardens and may need annealing before a subsequent severe forming operation.
Applications and How to Choose Between 1050 and Neighbouring Grades
Typical applications follow directly from the combination of moderate hardenability and high achievable surface hardness: shafts and axles that are induction hardened on the bearing journals, gear blanks that are quenched and tempered before tooth cutting, pins and bushings, shear blades and agricultural cutting edges, hand tool components, and forged connecting parts such as clutch and transmission components. Induction or flame hardening is particularly well suited to SAE 1050 because a 0.50% carbon content gives surface hardness of 55 HRC to 60 HRC after a short austenitising cycle, with a tough pearlitic core supporting the case.
The selection logic is straightforward. If the part is to be welded, choose a lower carbon grade. If the part needs through-hardening above 30 mm, choose a low-alloy grade. If the part needs maximum surface wear resistance with a modest core strength and no welding, SAE 1050 is cost effective and widely available. If the part is to be cold formed severely, an annealed low carbon grade will save tooling cost. Documenting this decision in the purchase order, together with the delivery condition and the required hardness range after heat treatment, prevents most of the disputes that arise on this grade.
Inspection, Documentation and Common Misconceptions
A complete inspection package for SAE 1050 plate normally contains a mill test certificate showing heat number, chemical analysis and tensile results, plus dimensional inspection of thickness, width, length and flatness against the ordered tolerance class. Where the grade is intended for a safety-related part, ultrasonic examination to an agreed acceptance level and a hardness survey across the thickness are worth the extra cost, because the two failure modes that matter most - internal segregation from the casting process and insufficient core hardness after quenching - are invisible to dimensional checks.
Several misconceptions recur. The first is that "1050" means 0.50% carbon exactly; it is a nominal designation within a range, and a heat at 0.48% will behave differently from one at 0.55% during hardening. The second is that higher austenitising temperature produces deeper hardening; it produces coarser grains, more distortion and greater cracking risk, without improving the depth of hardness. The third is that SAE 1050 plate can substitute for a low-alloy wear plate because both are "hard". A through-hardened 1050 at 55 HRC loses hardness rapidly at 200 C and above, whereas a properly alloyed quenched and tempered wear plate retains its hardness to higher tempering temperatures. The fourth is that a hardness reading taken on a mill scale surface is meaningful; scale must be ground off before testing, or the reading will be several points low.
FAQ
Q: What is the carbon range of SAE 1050 carbon steel plate?
SAE J403 specifies 0.48% to 0.55% carbon with 0.60% to 0.90% manganese, 0.030% maximum phosphorus and 0.050% maximum sulphur.
Q: Can SAE 1050 be welded?
It can be welded only with preheat of 200 C to 250 C, low-hydrogen consumables and a post-weld temper at 600 C to 650 C; the heat affected zone otherwise risks martensite cracking in sections above 12 mm.
Q: What hardness can be reached after quenching and tempering?
Water quenching from 800 C to 830 C followed by tempering at 200 C gives roughly 32 HRC to 38 HRC at the surface, or 55 HRC to 60 HRC after induction hardening without tempering.
Q: Is SAE 1050 through-hardenable in thick plate?
No. Its ideal critical diameter is about 25 mm to 35 mm in water, so plate thicker than roughly 25 mm will show a softer core and requires a hardness traverse to confirm the specified level.
Q: What is the European or Japanese equivalent of SAE 1050?
C50E to EN 10083-2 and S50C to JIS G 4051 are the closest equivalents, and GB/T 699 grade 50 corresponds; the equivalent grades carry tighter sulphur limits than the SAE specification.
Q: Why does SAE 1050 crack after quenching?
The usual causes are quenching a section too thick for the grade, austenitising above 850 C, failing to temper immediately after quenching, or quenching a part with abrupt section changes and sharp internal corners.




