Feb 05, 2024 Leave a message

DIN 1.2510, SKS3 and O1 Oil Hardening Tool Steel: Equivalents, Composition and Supply

What SKS3, O1 and 1.2510 Steel Is

SKS3, O1 and 1.2510 are three designations for the same family of material: a manganese-chromium-tungsten cold work tool steel that hardens in oil. The grade is a high-carbon alloy tool steel supplied in the annealed or pre-hardened condition as bar, plate and precision ground stock, and it is used for tooling that must hold a sharp edge or a precise dimension under repeated mechanical load at room temperature. Because it hardens in oil rather than in water, distortion during heat treatment is moderate and the steel is suitable for dies and punches with fine detail.

Grade Equivalents across Standards

Country Standard Grade designation
USA ASTM A681 O1
Germany DIN EN ISO 4957 1.2510 / 100MnCrW4
Japan JIS G4404 SKS3

The three designations are not numerically identical in every element limit, so a specification should always name the standard together with the grade. Where a drawing calls up O1 and the mill rolls to SKS3, the composition ranges overlap but the acceptance limits differ, and the mill certificate has to be read against the standard named on the purchase order.

Chemical Composition

Element (%) ASTM A681 O1 DIN EN ISO 4957 1.2510 JIS G4404 SKS3
Carbon (C) 0.85–1.00 0.90–1.05 0.90–1.00
Silicon (Si) 0.10–0.50 0.15–0.35 0.35 max
Manganese (Mn) 1.00–1.40 1.00–1.20 0.90–1.20
Chromium (Cr) 0.40–0.70 0.50–0.70 Per the applicable grade limits
Vanadium (V) 0.30 max 0.05–0.15 Per the applicable grade limits
Tungsten (W) 0.40–0.60 0.50–0.70 Per the applicable grade limits
Phosphorus (P) / Sulfur (S) 0.030 max each 0.030 max each 0.030 max each

The manganese content is what gives the grade its oil-hardening response, and tungsten together with chromium provides the wear resistance that lets a cutting edge survive in production blanking and forming. The low silicon range in the German designation is one of the visible differences between otherwise similar specifications.

Hardness and Heat Treatment

In the annealed condition the steel is supplied at a maximum delivery hardness of about 250 HB, which is soft enough for machining, milling and drilling to final tool geometry. After austenitising and quenching in oil, tempering brings the material to the working hardness required by the application; a commonly used oil quenched and tempered condition for this family is 28–34 HRC. Tooling that must resist abrasion is tempered at the higher end of the range, while tools that must absorb shock are tempered to the lower end for greater toughness. Tempering practice should be written into the process sheet, because repeated tempering in the wrong band, or the use of a temperature range that embrittles the grade, produces tools that fail in service for no visible reason.

Forms of Supply and Processing

Round bar, in the diameter range required for punches, guide pins and rolls, cut to length on request.

Flat bar and plate, cut to size for die plates, wear strips and bolsters.

Hexagonal bar and square block for special tooling and holding fixtures.

Precision ground flat stock and gauge plate, supplied to tight thickness tolerance for gauges, jigs and fixtures, in standard and non-standard sizes.

Machined blanks cut and squared from plate or bar where the customer prefers to start from a prepared block.

Typical Applications

The grade suits cold work tooling: blanking and piercing dies, forming and bending tools, punching tools and punches, shear blades, coining and embossing dies, gauges, jigs and fixtures, wear strips and machine tool components that need a combination of edge retention and dimensional stability. It is not intended for hot work or for high-speed cutting duty, where a hot work or high-speed steel grade is the correct selection.

Frequently Asked Questions

Q: Are SKS3, O1 and 1.2510 the same steel?
A: They are equivalent designations for the same oil-hardening cold work tool steel family, but the composition limits differ slightly between standards, so the standard must be quoted with the grade.

Q: What hardness is supplied?
A: Annealed stock is supplied at a maximum delivery hardness of about 250 HB; oil quenched and tempered condition is commonly specified at 28–34 HRC.

Q: What forms can the steel be supplied in?
A: Round bar, flat bar, plate, hexagonal bar, square block and precision ground flat stock or gauge plate.

Q: When should tempering be at the low or high end of the range?
A: Temper at the higher end where wear resistance dominates and at the lower end where the tool must absorb shock loading.

Q: Is this grade suitable for hot work tooling?
A: No. It is a cold work tool steel; hot work and high-speed cutting applications require a grade designed for elevated temperature service.

Q: What should the mill certificate state?
A: The standard and grade, the heat number, the chemical analysis and the delivered condition with its hardness.

Send Inquiry

whatsapp

phone

Email

Inquiry