What Is NM500 Steel Plate?
NM500 is a high-strength, wear-resistant steel plate produced to the Chinese standard GB/T 24186. The designation NM means wear-resistant steel, and 500 refers to the nominal Brinell hardness class of about 500 HBW, not a yield strength value. NM500 is supplied in the quenched and tempered condition, which gives the plate a hard, abrasion-resistant surface with a tempered martensitic structure that retains useful toughness. It is designed for high-wear service in mining, construction, and bulk material handling, where resistance to sliding abrasion is the primary requirement.
Chemical Composition
The chemical composition of NM500 is controlled to balance hardness, toughness, and weldability. Typical maximum values (percent by mass) are carbon about 0.38, silicon 0.70, manganese 1.70, phosphorus 0.020, sulfur 0.010, chromium 1.50, nickel 1.00, molybdenum 0.65, titanium 0.50, and boron in the range 0.0005-0.006, with acid-soluble aluminum at 0.01 minimum. Carbon and manganese provide the base strength and hardenability, chromium and molybdenum improve hardenability and tempering resistance, nickel supports toughness, and the boron addition allows full hardening of thicker sections during quenching.
Mechanical Properties and Hardness
The key performance parameter of NM500 is hardness. Typical hardness is about 470-540 HBW depending on plate thickness, with thinner plates toward the middle of the range. Tensile strength is in the order of 1350 MPa, minimum elongation about 7%, and Charpy V-notch impact testing can be specified at -20 deg C or -40 deg C with a minimum longitudinal impact energy of about 21 J. Hardness testing for acceptance is normally performed by the Brinell method, with Rockwell and Vickers methods used for specific applications. The mill certificate should state the actual hardness and tensile values for the delivered plate.
Typical Applications
NM500 is widely used in applications where resistance to abrasion is a primary concern, such as mining equipment liners, crusher parts, excavator and loader buckets, dump truck bodies, conveyor chutes and transfer points, and heavy-duty wear components in construction machinery. Its high hardness and durability allow thinner, lighter parts without compromising performance, which reduces material weight and operating cost. Because the grade is hard, it is more difficult to machine than softer wear grades, and specialized equipment and techniques are required for drilling and profiling.
Cutting, Welding, and Forming Notes
NM500 should be cut by plasma or laser with controlled heat input to limit hardening of the cut edge. Welding requires low-hydrogen consumables, low heat input, and usually preheating, and the weld zone will not match the base hardness, so mechanical fastening is preferred for wear-critical joints. Forming is possible with generous bend radii and sufficient press capacity, but the limited elongation of the grade must be respected. For applications needing easier machining, a softer grade such as 450 HBW class plate is recommended as a balance of hardness and workability.
Frequently Asked Questions
What does the 500 in NM500 mean? It refers to the nominal Brinell hardness class of about 500 HBW, not to a yield strength value.
How hard is NM500? Typical hardness is about 470-540 HBW depending on plate thickness, which is among the harder wear-resistant plate grades.
What is the tensile strength of NM500? Tensile strength is in the order of 1350 MPa, well above ordinary structural steel, which is why the grade is used for heavy wear parts.
Can NM500 be welded? Yes, with low-hydrogen consumables and controlled heat input, but the weld zone will not match the base hardness and may wear faster; bolting is often preferred for liners.
What is the difference between NM500 and NM400? NM500 has higher hardness (about 470-540 HBW versus about 360-440 HBW for NM400) and higher wear resistance, but lower toughness and ductility, so NM400 is better for impact-dominated service.
Which standard covers NM500? NM500 is covered by GB/T 24186; confirm the applicable edition, such as GB/T 24186-2022, and the acceptance criteria with the supplier.
Is NM500 easy to machine? No, the high hardness makes machining difficult and requires specialized tools; for parts needing extensive machining, a softer wear grade is more practical.




