What P20 Plastic Die Steel Actually Is
P20 is the AISI designation for a chromium-molybdenum alloy tool steel supplied in the pre-hardened condition and used almost exclusively for plastic moulds and die bases. In the AISI classification it belongs to the "mould steel" family rather than to the cold-work or hot-work families, and its defining commercial characteristic is that it arrives at the mould maker already hardened to roughly 28-34 HRC, so the cavity can be milled, drilled, tapped and finished without a subsequent quench-and-temper cycle that would distort the block. For a 500 mm x 800 mm cavity plate, that single fact removes one full heat-treatment step, one stress-relief step and the associated scaling, decarburisation and dimensional correction.
The grade is written as P20 in ASTM A681, as 3Cr2Mo in GB/T 1299, and as 1.2311 (nominally 40CrMnMo7) in the German and wider European designation system. Those three are not chemically identical, and the differences matter at the purchasing stage. AISI P20 carries a higher molybdenum range and a lower manganese range; 1.2311 shifts manganese upward and molybdenum downward to obtain deeper hardness penetration in thick sections; 1.2738 adds approximately 1% nickel on top of the 1.2311 base to improve hardenability further still, which is why it is routinely chosen for blocks above 400 mm thickness. None of these substitutions is "better" in the abstract - each trades polishability, weldability, machinability or through-hardness against the others.
Because the steel is delivered pre-hardened, the mill's hardening line, not the mould maker's heat-treat shop, controls the final microstructure. That makes the supply chain question a metallurgical one: was the plate austenitised at a temperature high enough to dissolve the chromium carbides, quenched fast enough through the core, and tempered uniformly enough that the hardness at mid-thickness matches the hardness at the surface? A plate that reads 30 HRC on the faces and 24 HRC at the centre will machine without complaint and then produce a mould that polishes differently on the two halves.
Chemical Composition and Cross-Standard Equivalents
The table below summarises the composition windows that a plate mill will normally certify for the four grades most often quoted against a P20 requirement. Values are expressed in weight percent and follow the ranges published in ASTM A681, GB/T 1299 and the corresponding European designation standards. Purchasers should treat them as the basis for a purchase specification, not as a substitute for the specific edition of the standard named on the mill certificate.
| Grade | Reference standard | C | Si | Mn | Cr | Mo | Ni | Typical delivery hardness |
|---|---|---|---|---|---|---|---|---|
| P20 (AISI) | ASTM A681 | 0.28-0.40 | 0.20-0.80 | 0.60-1.00 | 1.40-2.00 | 0.30-0.55 | - | 28-34 HRC |
| 1.2311 | DIN / EN tool steel designation | 0.35-0.45 | 0.20-0.40 | 1.30-1.60 | 1.80-2.10 | 0.15-0.25 | - | 28-32 HRC |
| 1.2738 (P20 + Ni) | DIN / EN tool steel designation | 0.35-0.45 | 0.20-0.40 | 1.30-1.60 | 1.80-2.10 | 0.15-0.25 | 0.90-1.10 | 28-34 HRC, more uniform in thick blocks |
| 3Cr2Mo | GB/T 1299 | 0.28-0.40 | 0.20-0.80 | 0.60-1.00 | 1.40-2.00 | 0.30-0.55 | - | 28-34 HRC |
| 1.2312 (P20 + S) | DIN / EN tool steel designation | 0.35-0.45 | 0.20-0.40 | 1.30-1.60 | 1.80-2.10 | 0.15-0.25 | - | 28-34 HRC, free-machining variant |
Two compositional details carry real consequences. First, sulphur: the standard P20 and 1.2311 windows cap sulphur at 0.030% or lower, whereas the resulphurised 1.2312 variant deliberately raises sulphur into the 0.05-0.10% range to break up chips during high-speed milling. The gain in machining productivity is real, but the sulphide stringers open up during polishing to produce "comet tails" and pin-hole defects on a mirror surface, and they reduce toughness in the Z direction. A mould for optical parts, light guides or high-gloss appliance fascias should therefore be ordered as low-sulphur, not free-machining.
Second, cleanliness. The inclusion content of a cavity block governs its polishing response far more than its hardness does. Plates intended for polishing or photo-etching are normally produced by electric-furnace melting followed by vacuum degassing and, in the better mills, vacuum arc or electroslag remelting. A purchaser can specify this objectively through macroscopic and microscopic inclusion ratings - ASTM E45 or GB/T 10561 for microscopic inclusion counts, and a SEP 1921 style macroscopic test for the larger defects that cause visible polishing pits.
Pre-Hardened Delivery Condition and Section Size Effects
P20 is quenched and tempered at the plate mill to the hardness band stated on the certificate, commonly written as 285-330 HB or its approximate Rockwell equivalent of 30-36 HRC, with 28-34 HRC the more usual commercial band for general plate. Hardness should be measured per ASTM E10 for Brinell or ASTM E18 / GB/T 230.1 for Rockwell, and the certificate should state the test location - surface, quarter-thickness or mid-thickness - because a single surface reading says nothing about the core.
Section size is the dominant variable. A 50 mm plate from a 1.2311 heat will harden essentially uniformly through its thickness. A 300 mm block from the same heat will show a measurable hardness drop toward the centre unless the composition includes sufficient manganese, chromium and molybdenum, or unless nickel has been added. This is why the practical rule in mould shops is: below roughly 200 mm, 1.2311 is sufficient; between 200 and 400 mm, specify a certified mid-thickness hardness rather than relying on the surface value; above 400 mm, either move to the nickel-bearing grade or accept a negotiated minimum core hardness and design the cooling layout around it.
Machining allowance and flatness also belong in the purchase order. Pre-hardened plates are supplied in the as-rolled or mill-machined condition, and residual stress from rolling and from the quench remains locked in the block. When a large cavity plate is machined by removing 30-40% of its volume from one face, that stress rebalances and the plate bows. The standard countermeasure is a two-stage process: rough machine with 2-4 mm of stock left on all faces, stress-relieve at approximately 500-550 C for 2-4 hours per 25 mm of section followed by slow furnace cooling, then semi-finish and finish. Mould makers who skip the intermediate stress relief and then blame the steel for a "warping" plate are usually describing their own machining sequence.
Mechanical Properties and Through-Thickness Uniformity
At 28-34 HRC the grade delivers a tensile strength in the region of 950-1100 MPa and a yield strength of roughly 800-900 MPa, with elongation in the 10-15% range and Charpy V-notch impact energy adequate for normal mould handling and clamping loads but not for high-shock blanking. Those figures belong to the tempered martensite produced by the mill's quench and temper; they do not describe an annealed block, and they degrade if the block is subsequently overheated during nitriding or repair welding.
Through-thickness uniformity shows up in three practical ways. It affects dimensional stability after cavity roughing, because a soft core yields plastically under clamping and clamping-induced distortion appears as a mismatch between the cavity and core halves. It affects polishability, because hard and soft bands abrade at different rates and a single polishing pass produces a wavy, "orange peel" surface that cannot be corrected by more polishing. It affects fatigue life of the mould, because the region of lowest hardness becomes the initiation site for heat-checking cracks when the mould runs with hot runners or aggressive cooling.
The verification method is straightforward and should be written into the inspection clause: hardness readings at a minimum of five points per face, plus one set at mid-thickness on a sacrificial extension or on the block ends if the geometry permits; a macrostructure check on a section for segregation and porosity; and ultrasonic inspection to GB/T 2970 or ASTM A578 for plate, or GB/T 6402 / ASTM A388 for forged blocks, with acceptance levels agreed in advance. For large mould bases, a Class 2 or Class 3 ultrasonic acceptance level is normally adequate; for mirror-polish cavities, a stricter level is justified.
Machining, Polishing and Texture Etching Behaviour
At around 30 HRC, P20 machines in the same envelope as a hardened and tempered alloy steel of that hardness rather than like an annealed tool steel. Roughing is normally done with coated carbide at cutting speeds of roughly 120-200 m/min, with depths of cut limited by the machine rather than the steel; finishing passes need sharp, positive-geometry inserts and a rigid setup because the material work-hardens slightly at the surface if the tool rubs. Drilling deep cooling channels is the operation most often underestimated: a 10 mm diameter hole at 25 times diameter requires peck drilling with high-pressure through-tool coolant, and any dwell produces a work-hardened band that will deflect the next drill.
Polishing response depends on inclusion content and hardness uniformity. Vacuum-degassed, low-sulphur material with an ASTM E45 thin-series inclusion rating kept low will take a high-gloss finish in the Ra 0.02-0.05 micron range using successive diamond grits, provided each step removes the scratches of the previous one and the operator does not skip grit sizes. Free-machining resulphurised grades will not reach that finish. Hardness variation between adjacent areas, whether from the mill's quench or from a local repair weld, shows up as a step in the polished surface that no amount of polishing removes.
Photo-etching and texturing follow the same logic. A uniform, fine-grained, low-inclusion structure etches evenly and reproduces the pattern mask faithfully; banded segregation or a coarse grain size produces a patchy texture with a visible "wood grain" orientation. Blocks intended for etching should be specified with a grain-size requirement and a cleanliness requirement, and should be textured after, not before, any stress-relief operation, because a stress-relieved surface etches to a different depth than a stressed one.
Heat Treatment: Hardening, Tempering and Nitriding
Although P20 is used pre-hardened, two thermal operations remain routine: re-hardening of small inserts or worn areas, and surface hardening by nitriding. Re-hardening follows the conventional sequence for a 0.35-0.40% C, 2% Cr, 0.2-0.5% Mo steel: austenitise in the 850-880 C range, hold to dissolve the carbides - time depends on section, roughly one hour per 25 mm after the part reaches temperature - then oil quench with agitation. As-quenched hardness lands near 50-54 HRC. Tempering immediately, without letting the part cool to room temperature, avoids cracking; a temper at approximately 200 C holds hardness at about 50 HRC, while tempering in the 500-600 C range brings it back to the 28-34 HRC mould-working band. Double tempering is preferred for any part with a heavy section change.
Nitriding is the standard route to a wear-resistant cavity surface without losing the pre-hardened core. Gas nitriding at 500-530 C for 20-40 hours produces a compound ("white") layer of roughly 5-15 microns over a diffusion zone of 0.2-0.4 mm, with surface hardness around 650-700 HV, equivalent to approximately 57-60 HRC. The compound layer is what resists abrasive filler and improves release; the diffusion zone supports it. Two cautions govern the process. First, nitriding temperature must stay below the original tempering temperature of the plate, otherwise the core softens and the whole benefit is lost - this is the single most common cause of a "nitrided but soft" mould. Second, sharp internal corners and thin ribs should be masked or given a shallower case, because a brittle compound layer on a sharp edge spalls during ejection.
Post-nitriding treatment should be limited to a light lap or a gentle abrasive flow, not to heavy grinding. Grinding through the compound layer removes the wear resistance while leaving the part looking finished, and grinding without coolant on a nitrided surface can generate cracking in the white layer.
Welding and Repair of P20 Moulds
Repair welding of a pre-hardened P20 cavity is common but unforgiving. The procedure that works is: preheat the surrounding area to 200-300 C, use a low-hydrogen consumable of matching chromium-molybdenum analysis applied with a short arc and minimum heat input, and let the weld cool slowly under insulation or a heat blanket rather than in still air. Skip the preheat and the heat-affected zone transforms to untempered martensite; that zone is harder than the surrounding steel, it will not polish to the same finish, and it becomes the initiation point for a crack that propagates into the cavity under cycling.
After welding, the repaired area should be tempered at approximately 500-550 C to soften the heat-affected zone back toward the base hardness, then dressed and blended. Weld metal will never match the base metal exactly in polish response, so repairs should be located where a slight difference is acceptable - in a non-cosmetic area, on a rib, or on a shut-off surface - rather than in the middle of a visible textured face. Where a repair is unavoidable on a cosmetic surface, the practical alternative is to cut out the damaged section, insert a matching pre-hardened plug, and weld only at the perimeter.
Applications, Mould Design Notes and Acceptance Checklist
The grade covers the mainstream of thermoplastic processing: injection moulds for appliance housings, television and monitor bezels, business-machine covers, battery cases, household containers and general consumer products; extrusion dies and die heads; blow-mould halves for bottles and containers; and mould bases and clamping plates that need to hold dimensional accuracy without a separate hardening step. It is a poor choice for highly abrasive glass-filled compounds at high volume, where a nitrided or through-hardened higher-alloy steel is warranted, and it is not intended for thermosetting resins, which normally call for a hot-work grade such as H13 because of the higher mould temperature and the corrosive by-products.
Design detail matters as much as grade selection. Cooling channels should be positioned no closer than about 1.5 times their diameter to the cavity surface to avoid a hard-to-cool thermal ridge, and the circuit should be balanced so that the core and cavity run within a few degrees of each other; unbalanced cooling warps the part and the mould. Ejector-pin holes need adequate support beneath them, since the pre-hardened plate is not hard enough to resist local brinelling under repeated ejection at high clamping loads.
A purchase specification that protects the buyer should state, at minimum: the grade and the standard edition against which composition is certified; the delivery hardness band and the test locations; the mid-thickness or core hardness for sections above 200 mm; the ultrasonic acceptance level and the inspection standard; the inclusion rating if the mould is to be polished or etched; the sulphur level, explicitly excluding resulphurised heats for cosmetic work; the dimensional tolerances and machining allowance per face; and the requirement for a stress-relief certificate if the mill performed one. Comparison of two quotations on price alone, without these parameters aligned, compares two different products.
FAQ
Q: What hardness does P20 plastic mould steel arrive at from the mill?
It is normally supplied pre-hardened to about 285-330 HB, which corresponds roughly to 30-36 HRC; the common commercial band for plate is 28-34 HRC, and the certificate should state the measurement location, not just one surface reading.
Q: Is 1.2311 the same as P20?
They are close relatives, not identical. 1.2311 raises manganese to about 1.30-1.60% and lowers molybdenum to about 0.15-0.25% compared with AISI P20, which improves hardness penetration in thick blocks while slightly reducing temper resistance.
Q: Why does my pre-hardened plate bow after rough machining?
Residual stress from rolling and quenching is released when material is removed unequally. Rough machine with 2-4 mm of stock, stress-relieve at about 500-550 C with slow cooling, then semi-finish and finish.
Q: Can P20 be nitrided, and what hardness results?
Yes. Gas nitriding at 500-530 C for 20-40 hours gives a compound layer of about 5-15 microns and a diffusion zone of 0.2-0.4 mm, with surface hardness near 650-700 HV, roughly 57-60 HRC.
Q: What is the maximum safe nitriding temperature?
It must remain below the tempering temperature used to produce the pre-hardened condition. Exceeding it softens the core and destroys the hardness that the plate was purchased for, even though the surface still reads hard.
Q: Should I choose the free-machining resulphurised version for a mirror-polish mould?
No. Sulphur in the 0.05-0.10% range improves chip control but the sulphide stringers open up during polishing and leave pits and comet tails, so cosmetic and optical cavities should use low-sulphur, low-inclusion material.




