Nov 06, 2024 Leave a message

Q245R Boiler Plate: Composition, Properties and Weldability

What the Q245R Designation Actually Tells a Fabricator

Q245R is a carbon steel plate grade written into GB/T 713, the Chinese standard covering steel plates for boilers and pressure vessels. The designation has three parts: the letter Q for the yield-strength prefix used across Chinese pressure equipment steels, the number 245 for the specified minimum room-temperature yield strength in megapascals over the thinner plate ranges, and the letter R for the vessel and boiler product family. The grade replaced the older 20R string when GB/T 713 was reorganised, and 20R still appears on legacy drawings, vessel data sheets and spare-part lists. The two designations are handled as technically equivalent in most procurement documents, but the purchase order should carry the current string so that mill certificates, third-party inspection reports and the nameplate all quote one grade rather than two.

Position matters as much as chemistry. Q245R sits at the bottom of the strength ladder of the vessel-plate family, below Q345R and well below the Cr-Mo grades such as 15CrMoR. That position is a design choice, not a shortcoming. Boiler drums, storage tanks, heat-exchanger shells, separators and low-pressure reactor bodies are usually governed by stiffness, corrosion allowance, nozzle reinforcement and code-allowable stress rather than by the need for a high tensile number. A low-carbon, low-strength plate gives the fabricator a wide welding window, generous ductility at shell-to-head junctions, lower residual stress after welding and a much smaller chance of delayed hydrogen cracking in thick weld metal. When a designer specifies Q245R, the intent is normally a robust, easily fabricated pressure boundary rather than a weight-optimised structure.

Chemical Composition and the Job Each Element Performs

GB/T 713 controls Q245R on ladle analysis, with product analysis permitted to deviate only within the limits of GB/T 222. The composition is deliberately lean: carbon is capped rather than specified as a range, manganese provides the bulk of the strength, and silicon is limited so that deoxidation is achieved without pushing strength up. The table below gives the customary limits together with the engineering reason behind each one.

Element Ladle analysis, % Role in the steel
C 0.20 max Sets the strength ceiling and, more importantly, the hardenability of the heat-affected zone; each additional 0.01% raises strength but narrows the welding window and raises hardness in thick-section welds
Si 0.35 max Deoxidation of the steel; excessive silicon degrades toughness and surface quality on thick plate
Mn 0.50-1.00 Solid-solution strengthening and sulphur control through MnS formation; the range is what allows the grade to reach 245 MPa yield without added micro-alloying
P 0.025 max Residual from ironmaking; held low because phosphorus segregates to grain boundaries and drives temper and step-cooling embrittlement in vessel service
S 0.015 max Residual; controlled to limit manganese sulphide stringers that cause lamellar tearing under through-thickness restraint and reduce Charpy energy in the short-transverse direction
Alt (acid-soluble Al) 0.020 min Fine-grain practice; aluminium nitride pinning keeps the ferrite grain size small, which is the cheapest route to good low-temperature impact energy

Two consequences follow from this table. First, Q245R is a fully killed, fine-grain steel, so heat input during welding is not as critical as it is for a coarse-grain micro-alloyed plate. Second, because there is no deliberate micro-alloying addition of niobium, vanadium or titanium, the grade does not depend on a controlled-rolling schedule to reach its properties, which is why it is available in the as-rolled, controlled-rolled and normalized conditions without large differences in the certificate values.

Mechanical Properties Across the Thickness Range

GB/T 713 grades the tensile requirements by thickness because the amount of rolling reduction and the cooling rate through the section both change with gauge. For Q245R the practical result is that a 10 mm plate and a 100 mm plate carry the same designation but not exactly the same minimum values. Buyers comparing mill certificates from two suppliers should first confirm that both certificates refer to the same thickness band.

Thickness range, mm Yield strength ReL, MPa min Tensile strength Rm, MPa Elongation A, % min Charpy V-notch at 0 degC, J min
3 to 16 245 400-520 25 34
>16 to 36 235 400-520 25 34
>36 to 60 225 400-520 25 34
>60 to 100 205 380-500 25 34

Three practical readings of this table matter during acceptance. The first is that the yield strength is a minimum, not a target: heats that come in at 300 MPa yield are not a defect and should not be rejected for being stronger than required, although a supplier quoting a narrow band should be able to explain the rolling practice behind it. The second is that the tensile range is two-sided. A plate at 530 MPa tensile fails the upper limit of 520 MPa, and that failure is meaningful, because an over-strength plate of this chemistry usually indicates either off-specification carbon or an unintended accelerated cooling practice, both of which change the toughness and the welding behaviour. The third is that the 0 degC Charpy requirement is the property that distinguishes a genuine vessel plate from a structural plate of similar strength: general structural grades such as Q235B under GB/T 700 are not tested to the same regime, so substituting them in a boiler shell is a traceability and liability problem, not merely a metallurgical one.

Why Buyers Specify Q245R: The Five Advantages in Practice

The performance case for the grade rests on five properties, and each of them has a specific fabrication or operating consequence rather than being a marketing phrase.

Strength with a comfortable margin. At 245 MPa minimum yield and 400-520 MPa tensile, a 20 mm shell in Q245R carries roughly the same design pressure as a thicker shell in a 235 MPa structural grade, and the allowable stress used in design codes leaves a margin against the 3.5 to 4.0 safety factor that vessel codes apply to tensile strength. The result is a plate that is strong enough for steam drums and separator shells up to moderate pressures while remaining easy to form.

Toughness that survives a cold start-up. The 0 degC, 34 J requirement, backed by aluminium-killed fine-grain practice and low phosphorus and sulphur, means the plate retains measurable fracture resistance well below the ambient temperatures seen in winter commissioning, unheated boiler houses and cryogenic-adjacent piping. Impact energy is not a guarantee against brittle fracture on its own, but a steel with a 0 degC transition requirement and low residual elements behaves predictably when a vessel is pressurised cold.

Weldability without heroics. With carbon capped at 0.20% and manganese at 1.00% maximum, the carbon equivalent of Q245R generally falls in a range where no preheat is needed for thin plate and only modest preheat, typically 100 degC or less, is used for thick sections or for high-restraint joints. Manual metal arc, gas metal arc, flux-cored and submerged arc processes all work; the filler selection is normally a 4303 or 4315 type electrode for matching strength, or a low-hydrogen 5015 type where the designer wants extra weld-metal toughness. The joint efficiency achieved in procedure qualification tests typically reaches the parent metal strength, so a shell seam does not become the weak link.

Formability for heads and shells. Elongation above 25% and a low yield-to-tensile ratio allow cold rolling of shell courses and cold forming of dished heads with modest springback. Shearing, plasma cutting and punching are all routine, and the plate does not require the inter-pass stress relief that high-strength quenched and tempered grades need after severe forming.

Stable properties at operating temperature. Boiler plates work continuously at 200-350 degC, and Q245R holds its strength and does not spheroidise its carbides in that window. Design allowable stresses are tabulated up to the temperature limit set by the code for carbon steel, and the grade is not intended for service in the creep range where Cr-Mo steels take over.

Welding Q245R: Procedure, Consumables and Post-Weld Heat Treatment

Welding procedure qualification for Q245R usually runs on the basis of GB/T 985 and the applicable vessel code, with the essential variables being thickness, heat input, preheat and post-weld heat treatment. Practical points that recur in fabrication shops:

Joint preparation and cleanliness. A double-V or single-V preparation with a 60 to 70 degree included angle and a root gap matched to the process keeps dilution predictable. Mill scale, rust and cutting slag must be removed from the groove faces and 25 mm either side; sulphur- and phosphorus-bearing contamination from marking paint is a common source of porosity and of low Charpy values in the weld metal.

Heat input. For 12 to 30 mm plate, a heat input of roughly 1.0 to 2.5 kJ/mm per pass balances productivity against toughness. Very high heat input coarsens the heat-affected zone and depresses its impact energy; very low heat input in thick sections raises hardness and hydrogen risk. Stringer beads are preferred over wide weave passes on the cap.

Preheat. Plates under about 25 mm in low-restraint joints generally run without preheat at shop temperatures above 5 degC. Above that, and for repairs, a preheat of 80 to 100 degC is usual, measured 75 mm from the weld toe, with inter-pass temperature held below 250 degC.

Post-weld heat treatment. Carbon steel vessel practice normally requires stress relief once the section exceeds roughly 32 mm, and also for any thickness where the design specifies it, where the joint is highly restrained or where the service involves wet H2S. The customary cycle is a hold at 580 to 620 degC for one hour per 25 mm of thickness with a minimum of one hour, heating and cooling at controlled rates above 400 degC. Over-tempering above about 650 degC is avoided because it can reduce strength below the minimum and, in the presence of residual phosphorus, work against toughness.

Forming, Cutting and Heat Treatment of the Plate

Cold forming is standard for shell courses up to about 30 mm and for heads; heavier plate is usually hot formed between 900 and 1050 degC and then normalized if the forming operation pushes the total strain beyond the limit at which the mill's original heat treatment is considered to be retained. Hot-formed and normalized components should be re-tested for mechanical properties on a coupon taken from the same plate and given the same thermal cycle, a requirement that is written into most vessel specifications and is frequently the reason a project needs test plates.

Thermal cutting leaves a hard, narrow edge zone. For Q245R the hardness is modest, but the cut edge on plate over 40 mm should still be dressed or machined back 1 to 2 mm before welding, and any edge that will carry a full-penetration weld should be inspected for laminations by ultrasonic testing.

Normalizing at 890 to 930 degC is available from the mill when the purchase order asks for it. Normalized delivery is common for thick plate, for plate intended for hot forming, and for components that will be stress relieved at high temperature, because the normalized structure is more stable than an as-rolled one during subsequent thermal exposure.

Q245R Against Q345R and SA516 Gr.70: Selection Logic

Most selection decisions come down to three grades. Q245R is chosen where the design is governed by corrosion allowance and stiffness, where welding is to be done in the field with limited preheat control, or where the operating temperature stays below the carbon steel limit. Q345R, with a 345 MPa minimum yield and higher manganese, allows a thinner shell for the same pressure and is the default for medium-pressure vessels and larger boilers; it costs more per tonne and needs tighter welding control. SA516 Gr.70 under ASME BPVC Section II Part A sits in a similar strength band to Q345R at 485-620 MPa tensile and 260 MPa minimum yield, and is normally specified when the vessel is to be code-stamped to ASME rather than to GB.

The mistake to avoid is treating these grades as interchangeable on the shop floor. A design calculated on Q345R allowable stress cannot be built in Q245R without re-checking the shell thickness, and a procedure qualified on Q245R does not automatically cover Q345R because the heat-affected zone hardenability differs. Matching the grade to the design calculation, and the welding procedure to the grade, is the only safe sequence.

Inspection, Testing and Acceptance Points for Procurement

A Q245R purchase order should pin down the following, because each item is a frequent source of dispute at goods-in inspection:

Certificate type. An EN 10204 3.1 certificate with heat number traceable to the plate stamping is the normal requirement for pressure parts; 2.2 certificates are acceptable only for non-pressure applications. The certificate must state the delivery condition, the heat treatment, the chemical analysis on ladle and product basis, and the tensile and impact results with test temperatures.

Impact test location and orientation. Charpy specimens are taken transverse to the rolling direction from a position representing the mid-thickness of the plate, and the certificate should show all three individual values as well as the average, since a single low value below 70% of the specified minimum is a rejection criterion in most codes even when the average passes.

Ultrasonic testing. Plate for pressure boundaries is commonly ordered with UT to a quality class covering laminations, particularly for thickness above 30 mm and for nozzle and manway regions where through-thickness stress acts.

Dimensional and surface checks. Thickness tolerance, camber, flatness and edge condition should be checked against the ordered standard; edge lamination, slivers and rolled-in scale are the defects most often found on arrival, and they are far cheaper to resolve before cutting than after.

Traceability through fabrication. The heat number should be transferred to every cut part. On a boiler job where Q245R and Q345R plates are both in the yard, a transferred marking system is the only defence against mixing grades in a shell course.

Common Misconceptions About the Grade

The first misconception is that a higher yield strength always means a better plate. For a vessel shell, an unnecessarily strong plate brings higher hardenability, more welding control and often lower toughness, with no design benefit. The second is that the R suffix makes the steel corrosion resistant. It does not: Q245R has no alloy addition for corrosion service, and where the internal environment is aggressive, the answer is a corrosion allowance, a coating, or a stainless or clad plate, not a change of carbon steel grade. The third is that post-weld heat treatment is optional below a certain thickness in every case. Thickness is one trigger; service environment, restraint and the design code are others, and the more restrictive requirement governs.

FAQ

Q: What is the minimum yield strength of Q245R plate?
Q245R is specified at 245 MPa minimum yield for plate from 3 to 16 mm, falling in steps to 205 MPa for plate above 60 mm and up to 100 mm, with tensile strength of 400-520 MPa and elongation of at least 25%.

Q: Is Q245R the same as the older 20R grade?
Q245R is the designation used in the current GB/T 713 edition for the grade previously written as 20R; drawings using the older string are normally converted, and the purchase order should state which designation the certificate is required to carry.

Q: What impact test does Q245R have to pass?
The grade is tested with Charpy V-notch specimens at 0 degC, with a minimum average of 34 J for full-size specimens, supported by aluminium-killed fine-grain practice and limits of 0.025% phosphorus and 0.015% sulphur.

Q: Does Q245R need preheating before welding?
Plate under about 25 mm in low-restraint joints usually needs no preheat when the shop is above 5 degC; thicker sections, high-restraint joints and repairs normally use 80-100 degC preheat with inter-pass temperature kept below 250 degC.

Q: When is post-weld heat treatment required on Q245R?
Stress relief becomes standard practice once the section exceeds roughly 32 mm, and is also triggered by the design code, by high restraint, or by wet H2S service; the typical cycle is 580-620 degC with a hold of one hour per 25 mm of thickness.

Q: Can Q245R be substituted for Q345R to reduce cost?
No, not without recalculating the design. The two grades have different allowable stresses and different heat-affected zone behaviour, so a shell designed on Q345R thickness must be re-checked and the welding procedure must be re-qualified if Q245R is proposed.

Send Inquiry

whatsapp

phone

Email

Inquiry