Jan 15, 2025 Leave a message

Q890E High Strength Steel Plate: GB/T 16270 Quenched and Tempered Plate

What Q890E High Strength Steel Plate Is

Q890E is a high strength structural steel plate covered by the Chinese standard GB/T 16270 and supplied in the quenched and tempered condition. The grade designation combines a minimum yield strength of 890 MPa with the E impact quality class, which means Charpy impact testing at -40 ℃. Quenching and tempering produces a tempered martensitic-bainitic microstructure, so the plate reaches a very high strength level while keeping the toughness and ductility that welded structures require.

Because of its high strength-to-weight ratio, Q890E plate is chosen where loads are heavy and section thickness has to be kept down. Under impact or vibration the plate keeps good stability and integrity and shows reliable impact and fatigue resistance in service. The material also responds well to cutting, bending and machining, so it can be shaped into complex fabricated parts without losing its properties.

Chemical Composition of GB/T 16270 Q890E

Table 1 lists the heat analysis limits specified for Q890E. Copper, chromium, nickel and molybdenum are added for hardenability and tempering resistance; boron raises hardenability at very small additions; vanadium, niobium and titanium contribute grain refinement and precipitation hardening.

Element Max %
C 0.20
Si 0.80
Mn 2.00
P 0.020
S 0.010
Cu 0.50
Cr 1.50
Ni 2.00
Mo 0.70
B 0.005
V 0.12
Nb 0.06
Ti 0.05

Mechanical Properties and Supply Range

Standard Grade Thickness Yield strength, min. Tensile strength Quality class
GB/T 16270 Q890E ≤ 50 mm 890 MPa 940-1100 MPa E, impact tested at -40 ℃

Plates are commonly supplied from 8 mm to 150 mm thick, 1 m to 3 m wide and 1 m to 12 m long, with other dimensions available to order. The same quenched and tempered family includes Q890D, Q960D and Q960E, which differ in strength level and in the impact test temperature of the quality class. Where a European grade is specified for the same structure, quenched and tempered products such as S690QL1 are used alongside Q890E, and ASTM A709 Grade 50 and S355J2 low alloy plates are applied where the strength demand is lower.

Fabrication and Processing Guidance for High Strength Plate

Cutting - the plate can be cut by flame, plasma or waterjet; for a steel of this strength a controlled thermal cut followed by slow cooling avoids a hard, brittle edge zone.

Forming - cold bending and rolling are used for structural shapes, and bend radii should be generous in relation to plate thickness because of the high yield strength.

Welding - low hydrogen consumables matched to the parent metal are used with careful control of preheat, interpass temperature and heat input to protect the heat affected zone.

Machining - the quenched and tempered structure machines predictably, but tool selection and feed rates must suit a steel with an 890 MPa minimum yield strength.

Surface protection - plates are delivered clean and can be shot blasted and painted or otherwise coated to the agreed specification.

Typical Applications and Quality Control

High strength plate of this class is used for crane and lifting structures, excavator and mining equipment bodies, heavy transport frames and tipper bodies, concrete pump booms, bridge and tower components and other heavily loaded fabrications where weight saving matters. Each heat is verified by heat analysis against the limits in Table 1, and mechanical testing covers yield strength, tensile strength, elongation and the impact test required by the E quality class. Dimensional checks cover thickness, width, length, flatness and edge condition, and test certificates are issued with the delivery so that every plate can be traced back to its heat number.

FAQ

Q: What does the E in Q890E mean?
The quality class E indicates that Charpy impact testing is performed at -40 ℃, giving assurance of toughness at low service temperature.

Q: What is the minimum yield strength of Q890E plate?
For thickness up to 50 mm the minimum yield strength is 890 MPa and the tensile strength range is 940-1100 MPa under GB/T 16270.

Q: Which thicknesses can be supplied?
Q890E high strength steel plate is normally supplied from 8 mm to 150 mm in thickness, with width of 1 m to 3 m and length of 1 m to 12 m, or to agreed dimensions.

Q: Is Q890E difficult to weld?
It is weldable when low hydrogen consumables are used with controlled preheat and heat input, and a qualified welding procedure is recommended for critical joints.

Q: Which other grades belong to the same family?
The quenched and tempered family includes Q890D, Q960D and Q960E; European quenched and tempered grades such as S690QL1 cover a similar strength band.

Q: Can the plate be supplied cut and bent to size?
Yes. Plates can be cut, bent and machined to agreed drawings, with surface preparation such as blasting and priming applied before dispatch.

Send Inquiry

whatsapp

phone

Email

Inquiry