Oct 31, 2025 Leave a message

QUALITY-CERTIFICATE-S355J0W.pdf

S355J0W Corten Steel Plate: Yield Strength, Tensile Strength and Specification

S355J0W Corten Steel Plate at a Glance

S355J0W corten steel plate is a hot rolled product with improved atmospheric corrosion resistance, used for shipping containers, steel bridges, vessels and tanks that work outdoors. Before ordering, buyers compare three figures: the specified yield strength, the tensile strength range and the thickness band that decides both. The sections below set out the standard, the chemical composition and the mechanical values behind those figures, together with the dimensions and tests that apply to a normal supply.

Standard and Designation

S355J0W is supplied under EN 10025-5, the standard for structural steels with improved atmospheric corrosion resistance. The older EN 10155 designation for these grades has been withdrawn and should not be quoted for new material. In the grade name, S marks structural steel, 355 is the minimum yield strength in MPa, J0 is a 27 J Charpy requirement at 0 degrees Celsius, and W is the weather resistant suffix. The same material is ordered as S355J0W steel plate, S355J0W steel sheet, S355J0W atmospheric corrosion resistance steel or S355J0W structural plate, and it is equally known as S355J0W corten steel plate.

Chemical Composition

Typical ladle analysis for the grade is given below. Copper is the addition that most directly drives the protective oxide layer, and chromium and nickel support it where they fall inside the specified ranges.

Element C Si Mn P S Cu Cr Ni
Typical, percent 0.13 max 0.40 max 1.60 max 0.035 max 0.030 max 0.25-0.55 0.40-0.80 0.65 max

Yield Strength and Tensile Strength

Thickness S355J0W yield min S355J0W tensile Elongation min Min impact energy
up to 16 mm 355 MPa 470-630 MPa 22 percent 27 J at 0 degrees C
16 to 40 mm 345 MPa 470-630 MPa 22 percent 27 J at 0 degrees C

Yield strength steps down slightly as the plate thickens because the through thickness cooling rate after rolling changes, which is why the 16 mm boundary matters at the detailing stage. The impact figure is longitudinal Charpy energy measured at 0 degrees Celsius, and it applies to both bands. Tensile strength stays inside the same 470-630 MPa window, so a thicker plate does not force a different allowable stress in the same design.

Dimensions, Surface Treatment and Testing

Thickness: 2 mm to 450 mm.

Width: 1000 mm to 4200 mm.

Length: 3000 mm to 18000 mm.

Surface treatment: shot blasting and painting, or coating, when a prepared surface is required.

Testing: tension test, impact test and ultrasonic examination.

Plate in the as rolled condition can be supplied when the surface will later be blasted and coated on site, and the high strength to weight ratio of the weathering grade supports the low wall thickness used in containers and tanks.

Frequently Asked Questions

Q: What is the yield strength of S355J0W corten steel plate?
A minimum of 355 MPa for thickness up to 16 mm and a minimum of 345 MPa from 16 mm to 40 mm. Tensile strength is 470-630 MPa and minimum elongation is 22 percent in both bands.

Q: Which standard covers S355J0W?
EN 10025-5, the standard for structural steels with improved atmospheric corrosion resistance. The earlier EN 10155 designation has been withdrawn, so new plate should be ordered against EN 10025-5 and tested accordingly.

Q: What impact energy is required at 0 degrees Celsius?
27 J on longitudinal Charpy specimens, which follows from the J0 part of the grade name. That value applies to plate up to 16 mm and from 16 mm to 40 mm.

Q: What thickness and width ranges are available?
Thickness from 2 mm to 450 mm, width from 1000 mm to 4200 mm and length from 3000 mm to 18000 mm, so the grade covers light tank shells as well as heavy bridge plate.

Q: Which tests are carried out on a normal supply?
Tension testing confirms yield strength, tensile strength and elongation, impact testing covers the J0 requirement at 0 degrees Celsius, and ultrasonic examination checks internal soundness where the order calls for it.

Q: Does the plate need a coating?
Not for corrosion protection, because the copper, chromium and nickel content lets the surface form its own protective layer outdoors. Shot blasting with painting or coating is available when the application calls for a finished surface instead.

Send Inquiry

whatsapp

phone

Email

Inquiry