S890QL1 is a quenched and tempered plate steel with an 890 MPa minimum yield strength and a Charpy impact test temperature of -60 °C. It belongs to the high yield strength group of EN 10025-6, which covers the flat products descending from S460 through S690 to S890 and S960, and the L1 suffix is the coldest of the three impact classes offered at each strength level. For a fabricator working on structures that must stay ductile in arctic or offshore conditions, that suffix is the whole reason for choosing this plate rather than the more widely stocked S890Q.
Reading the Designation: S, 890, Q and L1
Each part of the name carries a separate acceptance requirement. S means structural. 890 is the minimum yield strength in megapascals at the thinnest tabulated thickness. Q means the steel is delivered in the quenched and tempered condition; it is not a toughness code at this position in the name. L1 is the toughness code, and it specifies that the Charpy V-notch test is performed at -60 °C. Written in full, the order line should read S890QL1 to EN 10025-6, with the nominal thickness and the inspection class added.
One point of confusion deserves to be settled early. A rolled or normalized structural plate such as S355J2 has a different metallurgical basis and a different strength class, and an abrasion resistant plate at 500 HBW has no specified yield strength for design at all. S890QL1 sits in a narrow product niche: maximum practical strength with verified low temperature toughness, at thicknesses where the quench can still through-harden the section.
Impact Class Comparison at the 890 MPa Level
At the 890 MPa strength level the standard publishes three impact variants. They share chemistry, strength level and delivery condition, and differ only in the test temperature and in the energy that must be reached. The table below sets out the acceptance values applied to the series in longitudinal Charpy testing on 10 x 10 mm specimens.
| Designation | Impact test temperature | Minimum absorbed energy, longitudinal | Typical service envelope |
|---|---|---|---|
| S890Q | 0 °C | 60 J | Indoor machinery, temperate climate structures |
| S890QL | -40 °C | 40 J | Cold store frames, winter-exposed equipment |
| S890QL1 | -60 °C | 30 J | Offshore, arctic and liquefied gas environments |
The step down in required energy from 60 J to 30 J is not a concession to weaker steel; it reflects the falling capacity of any steel to absorb energy as the test temperature drops. What matters for acceptance is that the specified energy is reached at the actual service temperature, with an allowance for the difference between test temperature and minimum design metal temperature. A structure rated for -45 °C service would be specified with the L class, whereas one rated to -55 °C needs the L1 class.
Chemical Composition and Its Practical Meaning
The grade is a low carbon, micro-alloyed, alloy strengthened steel. Carbon is limited to 0.20% so that the quenched structure can be tempered to a tough condition; the strength comes from manganese, chromium, molybdenum and nickel together with small boron and niobium additions, not from carbon.
| Element | C | Si | Mn | P | S | Nb | V | Ti |
|---|---|---|---|---|---|---|---|---|
| Max. % | 0.20 | 0.80 | 1.70 | 0.020 | 0.010 | 0.06 | 0.12 | 0.05 |
| Element | Cr | Ni | Mo | Cu | N | B | Zr | CEV |
| Max. % | 1.50 | 2.00 | 0.70 | 0.50 | 0.015 | 0.005 | 0.15 | 0.82 |
Note that the phosphorus and sulphur ceilings here are tighter than those of the S960 grade, 0.020% and 0.010% respectively. That difference is deliberate: at -60 °C, coarse inclusions and segregation bands become crack initiation sites, so the cleaner steel is required before the toughness can be certified at that temperature. When a buyer substitutes one grade for another on price, the sulphur ceiling is one of the invisible differences that will show up later as scatter in the impact results.
Nickel at up to 2.00% serves two purposes. It improves the low temperature toughness of the tempered martensite, and it widens the processing window during quenching of thicker sections. Molybdenum suppresses temper embrittlement, which is the loss of grain boundary toughness that occurs when certain impurity elements segregate during slow cooling through the tempering range; this is why heavy S890QL1 sections should not be cooled slowly after tempering without a documented reason.
Mechanical Properties by Thickness Range
The standard tabulates properties for two thickness bands, and the step between them is significant for designers who want to weld a 40 mm plate to a 70 mm plate in the same joint.
| Property | 3-50 mm | 50-100 mm |
|---|---|---|
| Minimum yield strength ReH | 890 MPa | 830 MPa |
| Tensile strength Rm | 940-1100 MPa | 880-1100 MPa |
| Minimum elongation A | 11% | 11% |
The reduction of minimum yield from 890 MPa to 830 MPa above 50 mm is not a manufacturing shortfall but a recognition that the cooling rate at the centre of a thick section is slower, producing a slightly coarser tempered structure. A design that assumes 890 MPa across a 70 mm section is therefore non-conservative, and a welded transition between thickness bands must be checked with the properties of the thicker plate.
Elongation of 11% on a proportional gauge length is adequate for structural design but leaves very little margin for cold forming. Any forming operation should be evaluated as a separate process step with its own acceptance criteria, and formed regions should not be relied upon to provide ductility in the finished structure.
For joints that carry load through the plate thickness, a Z-quality specification with a minimum reduction of area should be added. Lamellar tearing is a real risk in S890QL1 node welds because the through-thickness ductility of any quenched and tempered plate is limited by the inclusion stringers produced during rolling.
Quenching, Tempering and the Reason Thickness Matters
S890QL1 plate is produced by thermomechanical rolling followed by austenitizing, quenching and tempering. The quench must remove heat from the core fast enough to avoid ferrite or bainite forming there, because those products would both lower strength and damage toughness. This is the physical reason why the grade is not published for arbitrary thickness: beyond a certain section, no practical quench rate can guarantee the required structure through the full thickness.
Tempering is a controlled trade between strength and toughness. Raising the tempering temperature increases impact energy and lowers yield strength; lowering it does the opposite. The mill therefore tempers to a target window rather than to a single temperature, and the certificate values normally sit comfortably inside the specification rather than at its edges. A plate whose tensile result is at the very top of the range and whose impact energy is at the very bottom should be questioned, because it suggests the tempering was marginal.
Welding S890QL1 in Cold Service Fabrication
Welding this grade is a procedure driven activity, not a shop floor judgement. The three risks are hydrogen induced cold cracking, softening of the heat affected zone, and loss of the very toughness that the L1 suffix was purchased to guarantee.
Hydrogen control starts with the consumable. Filler metals should be low hydrogen grades with a diffusible hydrogen content of H5 or H10 according to ISO 3690, stored in heated holding ovens and issued in quantities that will be consumed within the working shift. Covered electrodes for high strength steels are specified under EN ISO 18275, solid and flux cored wires under EN ISO 14341 and EN ISO 17632, and submerged arc combinations under EN ISO 14171. Consumable strength should generally match the 890 MPa level for butt welds, while slightly undermatching deposits are often accepted where restraint is high and the softened zone governs the joint anyway.
Preheat and interpass temperature are calculated from carbon equivalent, thickness, joint restraint and hydrogen level using the guidance of EN 1011-2, and the resulting procedure is qualified to ISO 15614-1. The cooling time from 800 °C to 500 °C is the variable that should be recorded, because it determines whether the heat affected zone becomes untempered martensite or an over-tempered soft band. Both extremes are unacceptable: the first risks cracking, the second reduces joint efficiency below the design assumption.
Heat input should be kept inside the qualified window and interpass temperature capped. Multi-pass welds in thick plate accumulate heat, and an unchecked interpass rise effectively tempers the previously deposited metal and the adjacent base metal, so hardness surveys on the finished joint frequently show a soft band several millimetres wide. Where a hardness limit is part of the specification, it should be checked on the actual production joint rather than only on the qualification test piece.
For -60 °C service, weld metal and heat affected zone toughness must be qualified at the same temperature as the base plate. This is often the deciding factor in consumable selection, because a consumable that matches base metal strength may still fail the -60 °C Charpy requirement in the as-welded condition.
Fracture Mechanics and Fitness for Service
Structures designed at 890 MPa with -60 °C toughness are typically assessed for crack tolerance rather than only against a yield criterion. Where a project requires it, critical crack tip opening displacement testing is performed to ISO 12135 or ISO 15653 on weld metal, fusion line and coarse grained heat affected zone specimens, and the results are used in an engineering critical assessment to set inspection intervals and acceptable flaw sizes.
The practical value of this approach is that it converts inspection results into accept or reject decisions with a defensible basis. A buyer who intends to use an engineering critical assessment should state the requirement in the order, because the test specimens must be taken from the production weld with the qualified procedure and the sampling position agreed in advance.
Cutting, Forming and Machining Notes
Thermal cutting of S890QL1 produces a narrow hardened layer, and plasma cutting is generally preferred over oxy-fuel cutting for internal profiles and small openings. Hardened cut faces that will be welded should be ground back to sound metal; faces that will carry fatigue load should be dressed to remove the notch effect of the cut drag lines.
Cold bending is possible but restricted. Internal radii in the order of three to four times the plate thickness, with the bend line transverse to the rolling direction and clear of cut edges, represent normal practice for this strength class. Tighter radii require hot forming, which destroys the quenched and tempered condition and obliges the fabricator to re-heat treat and re-test the component, a step that is rarely economical.
Machining is routine with carbide tooling and flood coolant, provided the plate is adequately supported to avoid vibration. The main risk is not the cutting itself but the local overheating that occurs when a worn tool rubs rather than cuts; the resulting tempered patch can reduce surface hardness and, in a fatigue sensitive detail, become a crack origin.
Ordering, Inspection and Documentation
An order that correctly specifies S890QL1 to EN 10025-6 still leaves several decisions open. The nominal thickness and its tolerance class should be stated, with tolerances to EN 10029 and the tighter class chosen where automated welding will be used. Surface condition should reference EN 10163, and internal soundness should reference EN 10160 with the acceptance class named, since the default class may not suit a highly stressed joint.
Mechanical testing covers tensile properties and Charpy impact energy per test unit, and the certificate should report the actual results, the test temperature and the specimen orientation rather than only the specification limits. Inspection documents are normally issued to EN 10204 type 3.1; a type 3.2 certificate witnessed by a nominated inspection body is commonly required for offshore and lifting applications and should be agreed before rolling, since it affects scheduling.
Handling and storage deserve a line in the purchase specification for this grade. Plates should be lifted with slings protected against edge damage, stacked on level bearers with sufficient support points to prevent permanent set, and kept clear of standing water. Edge damage and denting are not cosmetic issues on a 890 MPa plate, because a notch at a highly stressed edge is exactly the condition that the low temperature toughness allowance is intended to tolerate rather than to invite.
FAQ
Q: What does the L1 suffix mean on an S890QL1 plate?
The L1 suffix specifies that Charpy V-notch impact testing is carried out at -60 °C, the coldest of the three impact classes published for this strength level. It does not change the chemistry or the 890 MPa minimum yield requirement.
Q: Why is the minimum yield strength lower above 50 mm thickness?
Because the cooling rate at the centre of a thick section is slower, the tempered structure is slightly coarser. The standard therefore tabulates 830 MPa minimum yield for the 50-100 mm band instead of 890 MPa.
Q: Can S890QL1 be substituted for an S890Q plate?
Substitution in that direction is technically acceptable because QL1 satisfies a colder test temperature than Q, but the price and lead time are higher and the tighter sulphur and phosphorus limits may affect availability. Substitution in the opposite direction is not acceptable for cold service.
Q: What is the carbon equivalent limit for this grade?
The carbon equivalent value is capped at 0.82. It is high in absolute terms, but it derives from alloying elements rather than carbon, and it is the reason welding requires a calculated preheat and strict hydrogen control.
Q: Is post-weld heat treatment required after welding S890QL1?
Not normally. The plate is already tempered, and a further heat treatment risks reducing strength below the specified minimum. Where a heat treatment is imposed for other reasons, the procedure must be qualified and the mechanical properties re-verified afterwards.
Q: How should -60 °C toughness be verified on a welded joint?
By Charpy testing of weld metal, fusion line and heat affected zone specimens at -60 °C as part of the procedure qualification to ISO 15614-1, with results reported in the qualification record. Fracture mechanics testing to ISO 15653 may be added where an engineering critical assessment is required.




