Dec 23, 2024 Leave a message

S960Q Quenched and Tempered Steel Plate: Chemistry and Welding

S960Q is a quenched and tempered structural steel plate defined in EN 10025-6, the part of the European standard for hot rolled flat products that covers high yield strength structural steels delivered in the quenched and tempered condition. In the designation, the letter S marks structural steel, the number 960 is the minimum specified yield strength in megapascals for the thinnest tabulated thickness range, and the suffix Q fixes the minimum Charpy impact testing temperature at 0 °C. The same strength level is also published as S960QL and S960QL1, tested at -40 °C and -60 °C, so S960Q is the room temperature variant of the highest class covered by that standard.

What the Q Suffix Actually Fixes

Buyers frequently confuse the impact suffix with a quality label. It is not. Q, QL and QL1 differ only in the temperature at which the Charpy V-notch test is performed and in the energy level that must be met at that temperature. A Q plate is verified at 0 °C, an QL plate at -40 °C and an QL1 plate at -60 °C. All three must still reach the same minimum yield and tensile strength, and all three are supplied in the same quenched and tempered condition with the same chemistry limits. The practical consequence is that a Q plate may be entirely adequate for a machine frame in a heated workshop and entirely unsuitable for a structure that must remain ductile in winter service, even though both carry the number 960.

Because the impact test is the discriminating acceptance criterion, the ordering line should always state the grade letter, the impact class, the nominal thickness, the delivery condition and the inspection document required. A line that reads only "960 steel" leaves the mill free to choose the impact class, and the price difference between Q and QL1 delivery is not trivial.

Strength Positioning Against Lower Quenched and Tempered Grades

The value of S960Q only becomes clear when it is compared with the grades it usually replaces. Moving up the strength ladder allows a designer to reduce section thickness, and therefore dead load and weld volume, but each step also narrows the welding window and raises the demand on fabrication discipline.

Grade Min. yield ReH at 3-50 mm (MPa) Tensile range Rm (MPa) Typical design consequence
S460Q 460 540-720 Heavy sections, generous weldability margin
S690Q 690 770-940 Mobile equipment booms, bridges with slender girders
S890Q 890 940-1100 Crane jibs, high load brackets, weight-critical frames
S960Q 960 980-1150 Maximum strength per millimetre, thinnest practical sections

The progression from 460 MPa to 960 MPa roughly halves the required cross section for a purely tensile member at constant load, but deflection rather than stress usually governs the final design. That is why S960Q pays off in structures where stiffness is provided by geometry or where the mass of the moving part itself is the dominant load, and why it is a poor choice for a simple beam whose depth is already fixed by deflection limits.

Chemical Composition and the Function of Each Element

The chemistry is deliberately lean in carbon and rich in micro-alloying and alloying elements, because toughness at 960 MPa cannot be obtained from a high carbon content. Carbon is capped at 0.20% so that the martensitic structure produced by quenching can be tempered without severe loss of toughness, and sulphur and phosphorus are held low to limit inclusion damage and temper embrittlement.

Element C Si Mn P S Nb V Ti
Max. % 0.20 0.80 1.70 0.025 0.015 0.06 0.12 0.05
Element Cr Ni Mo Cu N B Zr CEV
Max. % 1.50 2.00 0.70 0.50 0.015 0.005 0.15 0.82

Nickel and manganese depress the transformation temperature and improve low temperature toughness of the tempered martensite. Chromium and molybdenum raise hardenability so that thick plates through-harden during quenching rather than forming softer transformation products in the core. Boron is used in very small amounts to suppress ferrite and pearlite formation at the grain boundaries, and because boron loses its effect when nitrogen is free, titanium or aluminium is added to fix nitrogen as nitride. Niobium and vanadium contribute to grain refinement during thermomechanical processing and to secondary hardening during tempering.

The carbon equivalent value is capped at 0.82 for the S960 class, which is high in absolute terms but is the result of alloying rather than carbon. Fabricators should understand that a low carbon content does not by itself make a 960 MPa plate easy to weld: the alloying elements that deliver the strength also raise hardenability, and the heat affected zone is therefore prone to cold cracking unless hydrogen and heat input are controlled.

Mechanical Properties Over the Tabulated Thickness Range

For plates from 3 mm to 50 mm, the standard requires a minimum yield strength of 960 MPa, a tensile strength between 980 MPa and 1150 MPa and a minimum elongation of 10% on a proportional gauge length. The narrow spread between yield and tensile strength, only 20 MPa of margin at the lower end, is a deliberate design feature: it forces the mill to produce a uniform tempered structure rather than a strongly work-hardened surface layer, and it warns the fabricator that little strain hardening reserve exists after cold forming.

Property Requirement Comment for the buyer
Nominal thickness 3-50 mm Thicker ranges are tabulated with a reduced minimum yield value
Yield strength ReH, min. 960 MPa Verified by tensile test in the transverse direction
Tensile strength Rm 980-1150 MPa A result above 1150 MPa indicates insufficient tempering
Elongation A, min. 10% Proportional gauge, Lo = 5.65 x square root of So
Impact KV, longitudinal 40 J at 0 °C, 30 J at -20 °C Charpy V-notch, 10 x 10 mm specimen where thickness allows

Thickness matters more than most buyers expect. Quenching intensity falls with increasing section, so the tabulated values apply to a defined range, and a plate ordered at 60 mm should be specified with the corresponding thickness range line rather than assumed to meet the 3-50 mm figures. Where a design requires through-thickness properties, the order must additionally call for Z-quality testing with a minimum reduction of area, because lamellar tearing in heavily restrained welded joints is a fabrication risk that the base grade does not address.

Delivery Condition and Mill Processing Route

S960Q is produced by a route that combines thermomechanical rolling with quenching and tempering. The slab is rolled in a temperature window that refines the austenite grain size, then reheated and quenched, typically by continuous roller quenching, to transform the structure to martensite. Tempering follows at a temperature chosen to reach the strength target while restoring toughness; it is a controlled compromise, because raising the tempering temperature improves impact energy and lowers strength in the same operation.

Because the final properties depend on the whole route rather than on chemistry alone, the mill's process control is the real quality guarantee. Buyers should require that the inspection certificate states the delivery condition as quenched and tempered, records the actual tensile and impact results per test unit, and confirms product analysis. A certificate that only reproduces the standard limits tells nothing about the actual plate that was shipped.

Welding S960Q Without Losing the Strength

Welding is the point at which most S960Q projects fail technically. Three mechanisms act at the same time: hydrogen induced cold cracking in the heat affected zone, softening of the tempering structure in the same zone, and loss of toughness when heat input becomes excessive. The welding procedure must be qualified for the actual combination of grade, thickness, joint type and consumable, following ISO 15614-1, and the preheat calculation follows the guidance of EN 1011-2.

Hydrogen control is not optional. Consumables should be low hydrogen grades with a diffusible hydrogen designation of H5 or H10 according to ISO 3690, held in heated quenches and used within the manufacturer's stated holding time. Covered electrodes for high strength steels are specified under EN ISO 18275, solid wires and flux cored wires under the corresponding EN ISO 14341 and EN ISO 17632 families, and submerged arc consumables under EN ISO 14171. A matching strength consumable is usual, but slightly undermatching consumables are often accepted for root runs and for joints where restraint is severe, because the softened zone limits the benefit of an overmatched deposit.

Heat input should stay inside a narrow band. Too low, and the cooling rate produces untempered martensite in the heat affected zone; too high, and the softened zone widens until the joint becomes the weakest section of the structure. The cooling time between 800 °C and 500 °C is the parameter that should be recorded in the procedure qualification record, together with preheat, interpass temperature and the number of passes. Interpass temperature is normally capped, since an unrestrained rise from long multi-pass sequences effectively re-tempers the previously deposited metal and the base plate beside it.

Butt welds in thick S960Q plate are commonly made with a symmetrical or double sided sequence to balance shrinkage stress, and temporary attachments such as lifting lugs should be welded with the same preheat and removed by cold cutting followed by grinding, never by hammering.

Forming, Cutting and Machining Practice

Cold forming of a 960 MPa plate is limited by its low elongation and high yield to tensile ratio. Bends should be designed with generous internal radii, in the order of three to four times the plate thickness for a 90 degree bend transverse to the rolling direction, and the bend line should never coincide with a flame cut or sheared edge. Where a tight radius is unavoidable, hot forming is possible but destroys the quenched and tempered condition, so the component must be re-heat treated and re-tested.

Thermal cutting leaves a hard, narrow layer at the cut face. For S960Q this layer should be removed by grinding or machining before the edge is welded or subjected to fatigue loading, particularly on plates above 20 mm where the cut face cools rapidly. Plasma and laser cutting produce a smaller affected layer than oxy-fuel cutting and are preferred for bracket profiles and openings. Drilling and boring are straightforward provided the plate is rigidly supported and carbide tooling with adequate coolant is used; work hardening of the cut surface during a poorly controlled drilling operation is a common source of cracked holes.

Inspection, Tolerances and Acceptance

Dimensional acceptance for S960Q plate is normally agreed to EN 10029 for thickness, width, length, flatness and edge condition, with the tighter of the available tolerance classes selected for plates that will be robotically welded. Thickness tolerances in particular should not be left to the default class: a plate ordered to a normal tolerance can be several tenths of a millimetre under nominal at the centre, which is enough to change the fit-up of a closed box section.

Internal soundness is verified by ultrasonic testing according to EN 10160, and the test class should be stated in the order. A class suitable for general structural use permits small, dispersed indications, whereas a class intended for highly stressed welded joints requires a cleaner product. Surface quality is judged against EN 10163, and any conditioning by grinding must remain within the permitted depth and must be blended smoothly.

The inspection document for structural plate is normally issued to EN 10204 type 3.1, which requires the certificate to be signed by an authorized inspection representative of the producing mill independent of the manufacturing department. For safety critical lifting equipment, buyers frequently ask for a type 3.2 certificate witnessed by a nominated third party, and this request has a real cost and lead time implication that should be settled before the order is placed rather than after rolling.

Where S960Q Is the Right Choice

The grade earns its cost in mobile and lifting equipment where the weight of the structure is itself a load: crane booms, excavator arms, concrete pump placing booms, aerial work platforms and heavy transport frames. It is also used in bridge rehabilitation where added dead load must be minimized, in hydraulic press frames, in mining shovel structures, and in offshore and port equipment where high static strength must be combined with adequate toughness.

It is a poor choice where the structure is governed by deflection, where the design demands extensive cold forming, where site welding will be performed without preheat and hydrogen control, or where the operating temperature falls below 0 °C with a requirement for ductile behaviour. In those cases S690Q or an QL variant at the same strength level is the technically defensible specification, and the design change is usually cheaper than the fabrication controls needed to make S960Q behave.

FAQ

Q: What is the difference between S960Q and S960QL?
Both grades have the same chemistry limits and the same 960 MPa minimum yield strength for 3-50 mm plate. S960Q is impact tested at 0 °C, while S960QL is impact tested at -40 °C, which is why QL is specified for cold climate and offshore service.

Q: Is S960Q the same as a 960 MPa abrasion resistant plate?
No. An abrasion resistant plate at 400 HBW or above is optimized for hardness and wear, not for weldability and structural toughness. S960Q is a structural grade with a controlled yield strength, a narrow tensile range and a specified Charpy energy, and the two product families should not be substituted for one another.

Q: What preheat is required before welding S960Q?
Preheat is not a fixed number. It is calculated from carbon equivalent, plate thickness, joint restraint and the diffusible hydrogen level of the consumable, following the guidance of EN 1011-2, and then confirmed by procedure qualification testing to ISO 15614-1.

Q: Why does the tensile strength have an upper limit?
The upper limit of 1150 MPa exists so that the plate retains a tempered structure with adequate toughness and elongation. A tensile result well above the range usually indicates under-tempering, and such a plate may pass the strength test while failing the impact requirement.

Q: Can S960Q be welded to lower strength structural steel?
Yes, and this is common in transition joints. The procedure is normally qualified on the higher strength side, preheat is governed by the more hardenable material, and the consumable is usually selected to match the lower strength grade so that the joint deforms in the ductile member rather than in the high strength heat affected zone.

Q: Does S960Q require ultrasonic testing on delivery?
Ultrasonic testing is not automatic for every structural plate, but for highly stressed joints and for thicknesses above roughly 20 mm it should be specified in the order, together with the acceptance class to EN 10160. Without a stated class the mill cannot know what internal quality the application requires.

Send Inquiry

whatsapp

phone

Email

Inquiry