Dec 18, 2025 Leave a message

SA612 Vs SA516 Gr.70: Which Is Better For Low-Temperature Pressure Vessels?

When designing low-temperature pressure vessels, selecting the right carbon steel plate is critical for safety, compliance, and long-term performance.
Two commonly compared ASME materials are SA612 and SA516 Grade 70.

 

So the question is:

Which steel is better for low-temperature pressure vessel applications - SA612 or SA516 Gr.70?

The answer depends on design temperature, impact toughness requirements, and project standards.

 

Overview of SA612 and SA516 Gr.70

 

 

SA612 steel ASME SA612 Steel Plate

  • High-strength carbon steel plate
  • Originally derived from ASTM A612
  • Designed for pressure vessels requiring higher allowable stress
  • Frequently used for:
  • Heat exchangers
  • Reactors
  • Columns and separators

 

ASME SA516 Grade 70 Steel Plate

  • Fine-grain carbon steel for pressure vessels
  • The most widely used ASME pressure vessel steel
  • Known for:
  • Good notch toughness
  • Stable low-temperature performance
  • Excellent weldability

 

Chemical Composition Comparison

 

 

Element SA612 (%) SA516 Gr.70 (%)
Carbon (C) ≤ 0.27 ≤ 0.28
Manganese (Mn) 0.85–1.20 0.85–1.20
Silicon (Si) 0.15–0.40 0.13–0.45
Phosphorus (P) ≤ 0.035 ≤ 0.035
Sulfur (S) ≤ 0.035 ≤ 0.035

📌 Chemically, the two steels are very similar.
The key difference lies in mechanical properties and toughness control.

 

Mechanical Properties Comparison

 

 

Property SA612 SA516 Gr.70
Yield strength ≥ 260 MPa ≥ 260 MPa
Tensile strength 415–550 MPa 485–620 MPa
Elongation ≥ 18% ≥ 17%
Impact test requirement ❌ Not mandatory ✅ Commonly specified

 

Low-Temperature Performance: Key Difference

 

 

SA612 steel SA516 Gr.70 - Better Toughness Control

SA516 Gr.70 is specifically designed for pressure vessels operating at low or moderate temperatures.

 

Advantages:

Frequently supplied with Charpy V-notch impact testing

Better notch toughness and crack resistance

Suitable for temperatures down to –20°C or lower (depending on impact requirements)

 

That is why SA516 Gr.70 is often required for:

Low-temperature storage vessels

LNG-related equipment (non-cryogenic)

Cold climate pressure systems

 

SA612 steel SA612 - Strength-Oriented, Not Toughness-Oriented

 

SA612 focuses on:

Higher allowable stress

Structural efficiency

Weight reduction

 

Limitations for low temperature:

Impact testing is not mandatory by default

Not ideal where brittle fracture risk exists

Typically used at normal or moderately low temperatures

👉 If SA612 is used for low-temperature service, additional impact testing and approval are required.

 

Which One Should You Choose?

 

 

 SA612 steelChoose SA516 Gr.70 if:

Design temperature is below 0°C

Impact toughness is mandatory

The vessel operates in cold climates

Safety margin is the top priority

 

Choose SA612 if:

Operating temperature is normal or slightly low

Weight reduction is important

Higher allowable stress is needed

Impact testing is specified additionally

 

SA516 Gr.70 and SA612 Supply from GNEE Steel

 

 

As a professional pressure vessel steel supplier, GNEE Steel offers:

✔️ ASME SA516 Gr.70 with impact testing

✔️ ASME SA612 with optional low-temperature impact tests

✔️ EN 10204 3.1 Mill Test Certificates

✔️ Stable quality for pressure vessels & heat exchangers

✔️ Global project experience

We help clients select the most cost-effective and code-compliant material for each application.

 

Request A Quote

 

GNEE Steel also supplies a variety of boilers and pressure vessel steel plates, such as A204 Grade B,A515 Grade 70,A537 Class 1,SA387 Grade 11 Class 1,P265GH,S537 Class 2,P355Q,P275N,P355N,P690Q,Q345R, etc. If you want to know more about other types of steel plates, you can call the consultation hotline at +8615824687445 or send an email to info@gneesteels.com. You are welcome to consult us, and we are very willing to answer your questions.

 

FAQ

What is SA 612 material?

carbon-manganese-silicon steel plate

SA612 is killed carbon-manganese-silicon steel plate made for welded pressure vessels. Its fine grain makes it suitable for use in moderate and lower temperature service where impact resistance is important.

What is the composition of ASTM A612?

ASTM A612 steel plate is a high-strength low-alloy (HSLA) steel plate designed for welded pressure vessels. It has a nominal composition of carbon, manganese, phosphorus, sulfur, silicon, nickel, chromium, molybdenum, and copper.

What is A612 steel?

ASTM A612 specification is the Standard Specification for Pressure Vessel Plates, Carbon Steel, High Strength, for Moderate and Lower Temperature Service. ASTM A612 encompasses carbon-manganese-silicon steel plates intended for use in welded pressure vessels for moderate and low temperature service.

Are SA612 and A612 Steel Plates the Same Product? What Are the Core Differences?

They are the same type of steel plate. ASTM A612 is the material standard, while ASME SA612 is the designation assigned after ASTM A612 was incorporated into the ASME Boiler & Pressure Vessel Code, specifically for the fabrication of pressure-bearing equipment.

What Are the Executive Standards for SA612/A612 Steel Plates? Are There Any Differences Between the ASTM and ASME Versions?

The executive standards are ASTM A612/A612M and ASME SA612. There are no substantial differences in chemical composition and mechanical properties between the two versions; the only variance lies in their applicable code systems.

What Are the Equivalent Grades of SA612/A612 in Chinese and European Standards? Can They Be Used as Direct Substitutes?

Common approximate equivalent grades include EN P355GH, DIN 1.0473, and GB Q345R. However, they cannot be used as direct equivalents. Their suitability must be confirmed in accordance with design specifications and approval requirements.

What Are the Yield Strength and Tensile Strength of SA612/A612? Do They Vary with Different Thicknesses?

The minimum yield strength of SA612 is approximately 260 MPa, and its tensile strength ranges from 485–620 MPa. As the thickness increases, the allowable minimum yield strength may decrease slightly.

What Are the Low-Temperature Impact Energy Requirements for SA612/A612? Are the Requirements at -40℃ and -45℃ Consistent?

Standards typically require impact testing at -40℃, while testing at -45℃ is not mandatory. If a project specifies -45℃ testing, additional impact tests must be conducted and clearly defined in the technical agreement.

What Are the Minimum and Maximum Service Temperatures for SA612/A612?

The recommended minimum service temperature is approximately -40℃, and the maximum operating temperature is generally around 400℃, depending on the design specifications and service medium.

What Is the Carbon Equivalent of ASME SA612? Is Preheating Required for Welding?

The carbon equivalent is usually around 0.42–0.45. Preheating at 50–120℃ is recommended for welding medium and thick plates. Commonly used welding materials include low-hydrogen electrodes such as E7018 and E7016.

What Is the Routine Thickness Range of SA612/A612, and What Is the Maximum Customizable Thickness?

The routine thickness range is 6–100 mm. Some steel mills can provide customized thicknesses up to 150 mm, subject to confirmation of their rolling and heat treatment capabilities.

What Are the Common Delivery Conditions for SA612/A612?

Common delivery conditions include As-Rolled (AR), Normalized (N), and Normalized + Tempered (N+T), with the normalized condition being the most widely used.

What Is the Machinability of SA612? Is It Prone to Cracking?

SA612 exhibits excellent cutting and bending performance. When processed with proper techniques and preheating, it is not prone to cracking.

Which Is More Suitable for Low-Temperature Applications: SA612 or SA516 Gr.70?

SA612 delivers more stable comprehensive performance in thick plate and high-stress working conditions, whereas SA516 Gr.70 offers better cost-effectiveness in conventional operating conditions.

Can Q345R Be Used as a Substitute for SA612?

Q345R can be used as a substitute in some working conditions for non-ASME projects. However, substitution is not recommended for export projects or scenarios where SA612 is explicitly required by specifications.

What Are the Differences Between SA612 and SA537 Cl.2?

SA537 Cl.2 boasts higher strength and low-temperature performance but comes with a significantly higher cost than SA612. It is suitable for more severe operating conditions.

Is SA612 Vessel Plate Suitable for LNG Storage Tanks?

SA612 is not recommended for primary LNG storage tanks operating at -162℃, but it can be used in LNG auxiliary systems or medium-to-low temperature vessels.

What Is the Hydrogen-Induced Cracking (HIC) Resistance of SA612 Steel Plates?

Standard SA612 does not mandate HIC resistance requirements. For applications involving sulfur-containing media, customized low-sulfur and low-phosphorus SA612 plates must be used, accompanied by HIC testing.

 

Other steel plate by GNEE
Name Material Specification (mm) Tons Remark
Clad steel plate P265GH+410,S355JR+410,A516Gr70+316,
A537CL1+304L,Q235B+304L,Q345B+304,
A516Gr70(NACE)+410,A537CL1+904L,
A537CL1+316L,A516Gr70+304L,A537CL1+304
,A516Gr70+410,A516Gr70+904L
2-300mm(Based plate),1-50mm(Composited plate) / UT, AR, TMCP.Normalized, Quenched and Tempered,Z Direction Test, Charpy V-Notch impact TestThe Third Party Test , Coated or Shot Blasting and Painting.
Low Alloy Q345A, Q345B, Q345C, Q345D, Q345E, Q390, Q420, Q460C, ST52-3, S355J2+N, SS400, SA302GrC, S275NL, 35CrMo 6 - 350 5788.56 Normalizing, tempered ,controlled rolling, hot rolling , Hot rolling,1st inspection, 2nd inspection, 3rd inspection
Pressure Vessel Plate Q245R, Q345R, Q370R, 16MnDR, 09MnNiDR, 15CrMoR, 14Cr1MoR, 12Cr2Mo1R, SA516Gr60, SA516Gr70, SA516Gr485, SA285, SA387Gr11, SA387Gr12, SA387Gr22, P265,P295,P355GH,Q245R(R-HIC),Q345R(R-HIC) 3 - 300 8650 Normalizing, tempered ,controlled rolling, hot rolling , Hot rolling,1st inspection, 2nd inspection, 3rd inspection
High-Strength Plate WH785D/E,Q960D/E, Q890D/E,WH60D/E,WH70B,Q550D,Q590D,Q690D/E 8 - 120 3086.352 Quenched and tempered
Wear-Resistant Plate NM360, NM400, NM450, NM500 6 - 150 3866.297 Quenched and tempered
Bridge Plate Q235qC, Q345qC, Q370qC, Q420qC, Q345qDNH, Q370qDNH, A709 - 50F - 2, A709 - 50T - 2 8 - 200 2853.621 Hot rolling, normalized ,hot rolling controlled rolling, quenched and tempered + toughness and brittleness

Send Inquiry

whatsapp

phone

Email

Inquiry