Mar 06, 2024 Leave a message

Development Trends in Surface Treated Steel Plate for Automotive Bodies

From Corrosion Protection to Multi-Functional Coating

Automotive surface treated steel plate began as simple corrosion protection for body panels, but the target has widened steadily. Since the 1970s the objective has been body corrosion prevention, and as durability targets were raised, the product family expanded to electrogalvanized plate, zinc alloy coated plate, alloyed hot-dip galvanized (galvannealed) plate and organic film coated zinc plate. More recently the driving requirements have become weight reduction, lower CO2 emissions, reduced environmental load and improved crash safety, which is why coating development now has to be compatible with very high strength substrates rather than competing with them.

The Main Coating Systems in Use

System Process Typical standard Design intent
Electrogalvanized (EG) Electrolytic zinc deposition ISO 3575 Uniform thin coating, good forming and surface quality
Hot-dip galvanized (GI) Continuous hot-dip zinc line EN 10346 / ASTM A653M Heavy sacrificial coating for exposed panels
Galvannealed (GA) Hot-dip zinc plus in-line diffusion anneal EN 10346 / ASTM A653M Zinc-iron layer with excellent spot weldability and paint adhesion
Zn-Al-Mg Hot-dip zinc alloy bath EN 10346 Higher cut-edge and crevice corrosion resistance
Organic composite coated Chromate or chrome-free passivation plus resin film Customer specification Additional barrier and anti-fingerprint function

Because the sacrificial action of zinc protects the steel even where the coating is damaged, zinc-based coatings have retained their dominant position. Increasing coating mass, designated for example Z275 on a hot-dip line, is a simple and effective way to raise corrosion life, and European specifications have historically run heavier coating masses than the galvannealed practice used in other regions.

Why High Strength Substrates Are Hard to Coat

Advanced high strength steels such as dual phase, transformation induced plasticity and bake hardening grades reach their strength through alloy design and heat treatment rather than through added thickness. When these grades are hot-dip coated, the strengthening elements manganese and silicon have a high affinity for oxygen and oxidise preferentially during the continuous annealing step that precedes the zinc bath. The resulting oxides, mainly silicon dioxide and manganese silicate, sit on the surface and reduce the wettability of the liquid zinc, which is one of the root causes of uncoated or bare spot defects.

Coating line practice therefore has to be tuned to the steel chemistry: controlled dew point and hydrogen content in the annealing atmosphere, optimised annealing temperature and line speed, and in some cases a modified alloy design that limits surface segregation of the oxidising elements.

Hydrogen Embrittlement and the Search for Alternative Coatings

Zinc protects steel by acting as a sacrificial anode, and that same mechanism creates a side effect. The anodic reaction on zinc is only weakly polarisable and the free corrosion potential is very low, close to -1.0 V in the standard hydrogen scale, so hydrogen can be generated and absorbed into the steel during the corrosion reaction. In extremely high strength grades this raises the risk of hydrogen embrittlement. Trials in which aluminium-magnesium-silicon alloy coatings partially replace zinc have shown that the drop in corrosion potential can be limited and hydrogen uptake reduced, which makes alloy selection a legitimate lever for improving delayed fracture behaviour, provided the corrosion protection level is retained.

Testing, Environmental Compliance and Market Trends

Accelerated corrosion testing follows neutral salt spray methods such as ISO 9227 and ASTM B117, supplemented by cyclic corrosion tests that better reproduce real vehicle exposure.

Coating mass, adhesion, formability and weldability are verified per delivery in line with EN 10346 for continuously hot-dip coated flat products.

End-of-life vehicle legislation has pushed the industry towards chrome-free passivation, since hexavalent chromium is restricted in automotive materials.

Lightweighting keeps raising the strength level of the substrate, so coating systems must maintain their performance on thinner, stronger panels.

Multi-layer systems combining a metallic coating with a thin organic film continue to grow in use for visible and structural panels.

Frequently Asked Questions

Q: What is the difference between galvanized and galvannealed plate?
Galvanized plate carries a zinc coating, while galvannealed plate is annealed in line so that iron diffuses into the coating and forms a zinc-iron layer with better welding and paint performance.

Q: Why do bare spots appear on coated high strength steel?
Because manganese and silicon oxides form on the surface during continuous annealing and prevent liquid zinc from wetting the steel, so the annealing atmosphere and steel chemistry must be controlled together.

Q: Does the coating affect weldability?
Yes. Coating type, coating mass and the presence of an organic film all influence resistance spot welding current windows and electrode life, so welding schedules are qualified per material combination.

Q: Is chrome-free passivation as effective as chromate?
Modern chrome-free systems are specified for automotive use and are accepted under end-of-life vehicle requirements, although the corrosion performance must be validated per application.

Q: How is coating mass specified for hot-dip products?
Coating mass is normally declared per unit area on both sides, for example a Z275 designation on a continuous hot-dip line, in line with EN 10346.

Q: Can surface treated plate be laser cut and formed normally?
Coated plate is routinely sheared, laser cut and formed, but tooling clearances and edge protection should be reviewed because the coating is softer than the steel substrate.

Send Inquiry

whatsapp

phone

Email

Inquiry