Three Requirements That Shape Automotive Steel Plate Today
Vehicle manufacturers must reduce part cost, cut weight and improve crash performance at the same time. Cost pressure is intense because the material itself, and above all the billet, accounts for the major share of a finished part, so lowering the cost of the base material is more effective than shaving processing steps. At the same time, CO2 and fuel consumption targets force every kilogram out of the structure, and safety targets push in the opposite direction by demanding more energy absorption and more robust joints than before.
That combination explains why automotive steel development has concentrated on strength per unit cost. Reducing the section size of a part is an efficient way to lose weight, but a thinner section with unchanged strength level also loses load-bearing area and clamping force at bolted joints. To keep the same robustness with less material, the strength level itself has to rise.
Materials Used for Automotive Wear and Strength Critical Parts
| Material group | Typical designation | Reference standard | Typical use |
|---|---|---|---|
| Wear-resistant plate | NM400, NM450, NM500 | GB/T 24186 | Dump truck bodies, mixer liners, tipper and mining attachments |
| High strength structural plate | S690QL | EN 10025-6 | Chassis brackets, crane and lifting structures |
| Advanced high strength sheet | Dual phase and transformation induced plasticity grades | Customer and OEM specifications | Body structure and reinforcement parts |
| Fastener wire rod | Property classes 8.8, 10.9, 12.9 | ISO 898-1 / GB/T 3098.1 | Bolted joints throughout the vehicle |
Why Strength Above Property Class 12.9 Is Difficult
Public standards and vehicle manufacturer specifications traditionally define property classes up to 12.9. In ISO 898-1 and the equivalent national fastener standards, class 12.9 corresponds to a nominal tensile strength of 1220 MPa, class 10.9 to 1040 MPa and class 8.8 to 800 MPa, with defined proof load, elongation and hardness windows.
Above that level the delayed fracture behaviour of conventional quenched and tempered steel deteriorates sharply. Delayed fracture is a hydrogen-assisted failure mode: hydrogen that has entered the steel migrates under stress and nucleates a crack that grows slowly, sometimes hours or days after assembly, without any visible deformation. Where a 10.9 or 12.9 part has already been used, further weight saving by reducing the section requires a material with a strength level greater than 12.9 together with a specific measure to restore the delayed fracture resistance, otherwise the design becomes unreliable.
Adding alloying elements is one established route to improve hydrogen tolerance in quenched and tempered grades, but alloying elements are expensive and the cost penalty is unavoidable, which pushes engineers to look at different microstructures instead.
The Non-Quenched-and-Tempered Route
Non-quenched-and-tempered steel takes the opposite approach. The part is not reheated and quenched after forming. Strength is instead built into the material through controlled cooling and treatment at the billet or wire rod stage and then developed by work hardening during drawing and forming, which gives a microstructure with a much greater resistance to delayed fracture than a tempered martensitic one and removes the heat treatment and the distortion control that goes with it.
Non-quenched-and-tempered grades normally contain more carbon than their quenched and tempered counterparts and are engineered to achieve high reduction of area at the rod stage. The trade-off is real: the material is harder than the tempered equivalent and much less forgiving in cold forming, and stress relief after severe cold forging may still be required to remove internal strain. Even so, high strength non-quenched-and-tempered parts have progressed steadily; reported strength levels have reached about 1600 MPa for engine applications and about 1400 MPa for body applications, and demand for this class of material is expected to keep expanding.
Design and Processing Consequences
Joint design must be revisited whenever the strength class rises, because proof load, tightening torque and hydrogen exposure all change together.
Hydrogen uptake has to be controlled at every step: pickling, electroplating, phosphating and any other wet process, followed by appropriate baking.
Wear-resistant plate is selected on hardness and abrasion index rather than tensile strength alone, and weldability of the higher hardness grades requires qualified procedures and preheat control.
Bending radius and forming limits tighten as strength increases, so tooling, springback compensation and edge quality become part of the material choice.
Corrosion protection must be maintained, because surface pits act as hydrogen entry points and as fatigue initiation sites.
Outlook
The direction is clear: automotive plate will continue to move towards higher strength at lower delivered cost, with the balance shifting between quenched and tempered, non-quenched-and-tempered and advanced high strength sheet grades depending on the duty of the part. Wear-resistant plate will keep replacing thicker plain carbon sections in truck bodies and attachments, while high strength structural plate takes over brackets and frames where fatigue life dominates.
Frequently Asked Questions
Q: Why is lightweighting so important for automotive steel plate?
Lower vehicle mass directly reduces fuel consumption and CO2 emissions, and part cost falls with mass as long as the strength level is raised enough to keep performance.
Q: What is delayed fracture?
It is a hydrogen-assisted cracking failure that occurs some time after a high strength part is loaded, and it becomes critical above property class 12.9 in quenched and tempered steel.
Q: What does non-quenched-and-tempered steel mean?
The part is not quenched and tempered after forming; strength comes from controlled cooling at the rod stage plus work hardening during drawing and forming, which improves delayed fracture resistance.
Q: Which standard covers wear-resistant steel plate?
In China wear-resistant plate grades such as NM400, NM450 and NM500 are defined in GB/T 24186, while high strength structural plate such as S690QL is defined in EN 10025-6.
Q: Are the strength classes the same worldwide for fasteners?
The property class system with 8.8, 10.9 and 12.9 is internationally aligned through ISO 898-1 and adopted in the corresponding national standards, so the mechanical requirements are comparable.
Q: Can higher strength always replace thicker plate?
No. Joint stiffness, fatigue life, buckling and hydrogen exposure must all be re-checked, and forming limits usually become tighter as strength increases.




