What the F316H (UNS S31609) Designation Actually Covers
F316H is not a separate alloy family; it is the product-form designation of grade 316H supplied as forgings. In ASTM A182/A182M the letter F prefixes forged or rolled flanges, fittings, valves, elbows and similar pressure-retaining components, so F316H means 316H in that form. The same chemistry and heat treatment delivered as plate is written 316H, UNS S31609, under ASTM A240/A240M for flat-rolled stainless plate, sheet and strip. In the European system the grade appears as X6CrNiMo17-12-2, material number 1.4919, in EN 10028-7 for pressure vessel plate and in EN 10088-2 for general flat products. The Chinese equivalent is written 06Cr17Ni12Mo2, with the elevated carbon band agreed at order stage because the standard table itself is built around the 0.08% carbon maximum of ordinary 316.
Understanding that identity matters in procurement. A purchase order that says only "316H plate" is open to three different delivery states: plate to A240, plate to A480/A480M general requirements plus A240, or plate to EN 10028-7. Each carries different dimensional tolerances, different test frequency and, critically, a different statement about grain size and elevated-temperature design values. The paragraphs below set out what F316H/316H is, how its carbon range changes mechanical behaviour relative to 316L, 316, 304/304L, 321 and 317L, and which acceptance points a buyer should write into the order.
Chemical Composition and Why the Carbon Range Defines the Grade
316H sits in the austenitic Cr-Ni-Mo family with roughly 16-18% chromium, 10-14% nickel and 2.0-3.0% molybdenum. The molybdenum addition is what separates the whole 316 branch from 304: it raises resistance to pitting and crevice attack in chloride-bearing water and in many organic and dilute acid streams. The feature unique to the H grade is carbon, held between 0.04% and 0.10% instead of the 0.030% maximum of 316L. That window is deliberate. Carbon in solid solution strengthens the austenitic lattice at temperature and, more importantly, supports the fine intragranular carbide precipitation that governs creep and stress-rupture behaviour above roughly 500 C. Too little carbon and the alloy creeps; too much and the risk of coarse grain-boundary carbide networks increases along with fabrication cracking sensitivity.
A240 chemistry limits for 316H are: carbon 0.04-0.10%, manganese 2.00% max, silicon 0.75% max, phosphorus 0.045% max, sulphur 0.030% max, chromium 16.0-18.0%, nickel 10.0-14.0%, molybdenum 2.00-3.00%, nitrogen 0.10% max. Because the carbon band is narrow, the steelmaker controls it in the AOD or VOD vessel rather than relying on scrap mix, and the heat analysis should be read as a positive range rather than a ceiling. Two heats that both report "0.05 C" can differ in nitrogen and in residual copper, tin and antimony; residuals above a few hundredths of a percent each raise hot-cracking sensitivity during welding and lower ductility in thick sections.
| Grade (UNS) | C % | Cr % | Ni % | Mo % | Typical role |
|---|---|---|---|---|---|
| 304 (S30400) | 0.08 max | 18.0-20.0 | 8.0-10.5 | - | General corrosion, food, architecture |
| 304L (S30403) | 0.030 max | 18.0-20.0 | 8.0-12.0 | - | Welded assemblies, no post-weld anneal |
| 316 (S31600) | 0.08 max | 16.0-18.0 | 10.0-14.0 | 2.00-3.00 | Chloride service, marine hardware |
| 316L (S31603) | 0.030 max | 16.0-18.0 | 10.0-14.0 | 2.00-3.00 | Chemical plant, welded vessels |
| 316H (S31609 / F316H) | 0.04-0.10 | 16.0-18.0 | 10.0-14.0 | 2.00-3.00 | Creep service above 500 C, thick sections |
| 321 (S32100) | 0.08 max | 17.0-19.0 | 9.0-12.0 | - | Titanium-stabilised, cyclic 400-900 C |
| 317L (S31703) | 0.030 max | 18.0-20.0 | 11.0-15.0 | 3.00-4.00 | Higher chloride and acid duty |
Mechanical Properties, Grain Size and the Elevated-Temperature Clause
At room temperature 316H and 316 land on the same minimums in A240: tensile strength 515 MPa (75 ksi), yield strength 205 MPa (30 ksi), elongation 40% in 50 mm, and hardness not exceeding 217 HBW or 95 HRB. That equality misleads buyers who expect the H grade to be visibly stronger on a tensile certificate. The difference appears at temperature. Under ASME BPVC Section II Part D the allowable stresses for 316H remain usable to far higher temperatures than those for 316L, because the property basis switches from tensile limits to creep and stress-rupture limits, and there the 0.04-0.10% carbon pays off. For a vessel or transfer line operating continuously at 550-700 C, 316H may be permitted where 316L is not.
The second differentiator is grain size. Coarse grains creep more slowly than fine grains at the same stress, so the H grades are produced with a deliberately larger austenitic grain. A240 requires the H grades to be solution annealed at a minimum temperature - 1,040 C (1,900 F) for 316H - followed by rapid cooling, and the mill certificate must state the measured ASTM E112 grain size. A fine-grained condition that passes every chemistry and tensile check can still fail in service by accelerated creep, which is why the grain-size figure, not just the word "H" on the stamp, belongs in the purchase specification.
Hardness limits are a related point of leverage. Because 316H is often used in thick forgings and heavy plate that see thermal cycling, a hardness ceiling of 217 HBW gives a crude but useful screen against improper annealing or excessive cold work. Any reading above the limit on a delivered plate, especially near a sheared edge, indicates an incomplete solution treatment and is grounds for rejection before fabrication begins.
Direct Comparison with 316L, 316, 304/304L, 321 and 317L
Against 316L the trade-off is simple and can be stated as a rule: below about 400 C and in wet corrosive service, 316L is the better choice because its low carbon removes the risk of sensitisation next to welds; above about 500 C and under sustained load, 316H is the better choice because its carbon carries the creep duty. Selecting 316H for a welded acid tank is a common error, and selecting 316L for a superheater support is a more expensive one, because the L grade's creep strength is insufficient and the design must be de-rated or re-detailed.
Against 316 the difference is only the carbon band, but that band matters in two ways. Ordinary 316 may contain up to 0.08% carbon with no lower bound, so a heat at 0.02% could be supplied under a 316 order and would behave like 316L at temperature. Ordering 316H closes that hole by imposing a floor as well as a ceiling. Against 304 and 304L the difference is molybdenum plus nickel: 316H carries 2-3% Mo and 2-4% more nickel, which lifts pitting resistance (expressed as PREN = Cr + 3.3Mo + 16N, roughly 25 for 316H against 18-19 for 304) and improves performance in chlorides and in high-temperature pressurised water. A 304 substitution is therefore never an equivalent for 316H in a chloride or high-temperature duty, even though the two are interchangeable for dry architectural work.
Against 321 the comparison is about how the carbon is immobilised. 321 adds titanium at not less than five times the carbon plus nitrogen content, tying carbon into stable TiC and preventing chromium carbide at grain boundaries; it is the classic choice for cyclic service between roughly 400 and 900 C where both creep strength and resistance to intergranular attack after welding are needed. 316H takes the opposite route - it deliberately leaves carbon free to strengthen the matrix and accepts that the material will sensitise if it is held in the 425-815 C range and later exposed to an aqueous electrolyte. 321 also loses creep ductility above about 600 C in some section sizes, so the choice is application-specific rather than generational: 321 for cyclic and welded-then-wetted duty, 316H for steady high-temperature load in dry or non-electrolytic environments.
Against 317L the axis is molybdenum content: 3.0-4.0% Mo against 2.0-3.0%, with PREN around 30 versus 25. 317L is a corrosion answer, not a temperature answer, and it is specified where 316L pits in chloride or in mixed acid service. For duplex alternatives such as UNS S32205 the contrast is even sharper: the duplex grade offers roughly 450 MPa minimum yield - more than twice 316H - with far better chloride stress-corrosion resistance, but its upper service temperature is limited to roughly 300 C because of sigma-phase formation, so it cannot replace 316H in hot creep duty at all.
Sensitisation, Sigma Phase and Real Temperature Limits
Sensitisation is the precipitation of chromium-rich carbides along austenitic grain boundaries between about 425 C and 815 C, which drains chromium from a narrow band beside each boundary and leaves it vulnerable to intergranular corrosion in acids and chloride liquors. The H grade sensitises faster than the L grade by design. This is acceptable when the component operates continuously above the precipitation range, when the environment is dry gas or molten salt rather than an electrolyte, or when the section is thick enough that the chromium-depleted band is a negligible fraction of the load path. It is not acceptable for a welded 316H component that will later hold dilute sulphuric acid or chloride-bearing cooling water.
Sigma phase is the second high-temperature hazard. In 316-type alloys, sigma - a hard, brittle intermetallic rich in chromium and molybdenum - forms on prolonged exposure in roughly the 600-900 C band, most rapidly in the 750-850 C region, and it destroys toughness and creep ductility. Long-term design above 600 C therefore needs an allowance for sigma, and any shop that stress-relieves heavy 316H weldments in that window for many hours is trading corrosion resistance and toughness against residual stress. Practical exposure limits depend on stress, environment and required life; ASME design curves and the material supplier's creep data, not a single blanket temperature, should govern the decision.
Thermal expansion is a third constraint that catches fabricators. Austenitic 316-class steel expands at roughly 16 x 10^-6 /K between 20 and 100 C, about 40% more than carbon steel, with thermal conductivity near 16 W/m.K - less than half that of carbon steel. Dissimilar joints to carbon steel bodies therefore need transition design, and the slow thermal response of thick 316H sections has to be allowed for in heat-up and cool-down rates to avoid harmful gradients.
Forming, Welding and Heat Treatment of F316H Components
Hot forming of 316H is carried out between roughly 1,150 C and 900 C, finishing above 900 C to avoid surface carbide precipitation, followed by solution annealing. Cold forming is possible but the alloy work-hardens rapidly: a shear modulus near 77 GPa and a high strain-hardening exponent mean that a 15-20% reduction in a single pass is often the practical limit before an intermediate anneal is required. Any cold-formed forging that has seen more than a modest amount of deformation should be solution annealed at 1,040-1,120 C and water quenched to restore creep resistance; a stress relief at 700-800 C is not a substitute and will actually sensitise the steel.
For welding, matching composition consumables are the default: covered electrodes to AWS A5.4 (E316H-15 or E316H-16 classification family) and bare wire or rod to AWS A5.9 in the ER316H classification. Where the joint will be exposed to aqueous corrosives after welding, an over-alloyed or L-grade filler is often preferred to keep the weld metal out of the sensitisation range. Process notes that materially affect quality are low heat input, stringer rather than weave beads, interpass temperature held at or below about 150 C, and wire brushing between passes with dedicated stainless tools. Preheating is not used; post-weld heat treatment is generally unnecessary for 316H because there is no hydrogen- or hardness-driven cracking mechanism, and if the application demands stress relief, the procedure should be justified against the sensitisation and sigma risks described above.
Plate Specification, Tolerances and Acceptance Points
Plate for pressure service is normally ordered as A240/A240M material with A480/A480M general requirements, hot rolled, annealed and pickled (finish No. 1), edges sheared or milled, ultrasonically examined when thickness or duty requires it, and supplied with an EN 10204 3.1 inspection certificate that ties the plate to its heat number. Thickness tolerance, flatness, camber and length tolerance come from A480/A480M for the inch-pound route and from EN 10028-7 with EN 10029 dimensional classes for the metric route; the two are not interchangeable, and a fabricator who assumes metric tolerances on an inch-pound order can be caught by a 0.3 mm shortfall on a 20 mm plate.
Acceptance should combine documents and physical checks. Document review covers heat number, product analysis against the A240 table, the minimum 1,040 C solution-annealing temperature and quenching method, tensile results against 515/205 MPa, hardness against 217 HBW, and the ASTM E112 grain size. Physical checks cover positive material identification - portable X-ray fluorescence readily separates 316 from 304 by detecting molybdenum, and separates 316H from 316L only through the certified chemistry - plus dimensions, surface condition, edge quality and a check for grinding or weld repair without documentation. Where intergranular corrosion resistance matters, ASTM A262 Practice E (copper-copper sulphate sulphuric acid) is the standard screening test, and where the part will be welded into wet service, a sensitisation test on a welded sample is more informative than a test on parent metal.
FAQ
Q: Is F316H a different alloy from 316H?
No. F316H is 316H supplied in forged or rolled product form under ASTM A182/A182M; the plate form of the same grade is 316H, UNS S31609, under ASTM A240/A240M.
Q: What carbon range does 316H require?
0.04% to 0.10% carbon, against a 0.030% maximum for 316L and a 0.08% maximum for standard 316.
Q: Does 316H have higher room-temperature strength than 316L?
No. Both carry the same 515 MPa tensile and 205 MPa yield minimums; the advantage of the H grade appears in creep and stress-rupture behaviour above roughly 500 C.
Q: Can 316H be substituted for 316L in a welded acid tank?
Not normally. The higher carbon makes 316H far more prone to sensitisation in the 425-815 C range, so welded equipment exposed to aqueous corrosives should use 316L, 316Ti/321 or 317L unless a documented stress relief and corrosion assessment supports otherwise.
Q: Which filler metal is used for welding 316H?
Matching ER316H solid wire or E316H covered electrodes are the default; an L-grade or over-alloyed filler is often chosen where the weld will see aqueous corrosive service.
Q: How is 316H plate identified at goods-in?
By the 3.1 certificate for chemistry, mechanicals, solution-annealing temperature and grain size, plus X-ray fluorescence to confirm molybdenum is present and to rule out a 304 substitution; carbon content itself must come from the certified analysis.




