What a Cold Rolled Steel Coil Is and Where It Sits in the Mill Route
A cold rolled steel coil is a hot rolled coil that has been pickled, cold reduced below the recrystallisation temperature, cleaned, annealed and temper rolled, then wound into a coil of several tonnes. The cold reduction step is what changes the material: the strip passes through a tandem mill with four to six stands and is squeezed from an entry thickness of typically 1.8 to 5.0 mm down to 0.20 to 2.00 mm, a total reduction of 50 to 90 percent. That severe deformation work-hardens the ferrite, raises yield strength, tightens thickness control and produces a surface that can be painted, plated or coated without further mechanical preparation.
The distinction that matters commercially is not "cold" versus "hot" as a temperature label but the finishing chain. A hot rolled pickled coil is delivered in the as-rolled metallurgical state with mill-scale removed; a cold rolled coil has passed through recrystallisation annealing so the work-hardened structure is replaced by a controlled grain structure. Buyers who specify "cold rolled" only by thickness and width often receive a full-hard product that cannot be deep drawn, because full-hard (unannealed) coil has yield strength in the region of 550 to 700 MPa and almost no elongation. The delivery condition therefore belongs in the purchase order alongside the grade.
The Rolling Route: Pickling, Cold Reduction, Cleaning and Oiling
Pickling removes the oxide scale produced in the hot mill. Hydrochloric acid lines operating at roughly 70 to 90 degrees Celsius with 10 to 20 percent acid concentration are the common route, followed by rinse and drying. Scale residue left on the strip is rolled into the surface during cold reduction and shows up later as rolled-in dirt or as pits after painting, so pickle line cleanliness is a genuine quality variable rather than a formality.
Tandem cold reduction uses oil-in-water emulsion for cooling and lubrication. Reduction schedules are distributed across stands so that the last stand delivers both the final gauge and the surface texture; work roll roughness in the last stand is what transfers the peak count and roughness average onto the strip. After rolling, the coil is degreased in an alkaline cleaning section, rinsed, dried and either electrostatically oiled or left dry. Oiling is not cosmetic: it prevents rust during ocean freight and storage, but the oil film must be compatible with the customer's downstream process. A press shop that welds and paints without degreasing needs a light, weldable, paint-compatible oil in the 0.5 to 2.0 g/m2 range per side, not a heavy protective film.
Strip tension, roll bending and roll shifting on modern mills give crown and flatness control that a 1980s mill could not achieve. This is why the same nominal grade from two suppliers can behave differently in a progressive die: flatness and residual stress distribution, not the chemistry certificate, usually explain the difference.
Grade Designations and What They Promise the Forming Operation
Cold rolled low carbon sheet is classified by formability, not by strength. In the European system of EN 10130 the designations run DC01 through DC07, where a higher number means a cleaner steel, lower carbon and a deeper drawing capability. The Japanese system of JIS G 3141 uses SPCC for commercial quality, SPCD for drawing quality, SPCE for deep drawing quality and SPCF and SPCG for the most severe drawing applications. ASTM A1008/A1008M covers commercial steel (CS), drawing steel (DS), deep drawing steel (DDS) and extra deep drawing steel (EDDS) types. The Chinese series GB/T 5213 addresses cold rolled low carbon sheet for cold forming with comparable quality tiers.
The practical meaning of a grade step is interstitial carbon and nitrogen control. Aluminium-killed, fully stabilised grades such as DC06 and EDDS use titanium or niobium to fix carbon and nitrogen as precipitates, which removes the yield point elongation that otherwise produces stretcher strains and Luders bands on formed panels. If a part is visible after forming and shows flame-shaped surface marks, the cause is almost always an under-stabilised grade rather than a press setting.
| Designation (EN 10130 / JIS G 3141) | Typical yield strength Rp0.2, MPa | Typical tensile strength Rm, MPa | Minimum elongation A80, percent | Typical forming duty |
|---|---|---|---|---|
| DC01 / SPCC (commercial quality) | 140 to 210 | 270 to 410 | 28 | Bending, roll forming, simple blanking |
| DC03 / SPCD (drawing quality) | 140 to 240 | 270 to 380 | 34 | Moderate drawing, medium-depth panels |
| DC04 / SPCE (deep drawing) | 140 to 210 | 270 to 350 | 38 | Deep drawn housings, oil pans, doors |
| DC05 (deep drawing, stabilised) | 140 to 200 | 270 to 330 | 40 | Complex geometry, low anisotropy demand |
| DC06 / EDDS (extra deep drawing) | 120 to 180 | 270 to 330 | 41 | Severe drawing, visible exterior panels |
| DC07 (highest formability) | 110 to 170 | 250 to 310 | 44 | Extremely severe forming, thick-to-thin sections |
Values in the table are representative ranges quoted by the standard; the mill certificate governs the actual acceptance. Two further parameters decide draw success more often than the tensile values: the plastic strain ratio r and the strain hardening exponent n. Deep drawing grades are expected to show r values of about 1.6 to 2.0 and n of 0.20 to 0.25, while commercial quality sits near r 1.0 to 1.2. A drawing shop that changes supplier on price alone should ask for r and n on the test report, not just Rm.
Annealing Route Decides the Final Properties
Recrystallisation annealing is performed either in a batch annealing furnace or on a continuous annealing line, and the two routes are not interchangeable for demanding parts.
Batch annealing stacks coils with convector plates in a bell furnace, heats to roughly 600 to 700 degrees Celsius over many hours and cools slowly under a hydrogen or nitrogen-hydrogen atmosphere. The cycle is slow, the capital cost is moderate, and the result is excellent formability with low strength, which suits deep drawing grades. The penalty is a coarser grain structure and a greater risk of carbon deposits if the atmosphere is poorly controlled.
Continuous annealing passes the strip as a single thickness through heating, soaking, slow cooling, over-ageing and final cooling zones in a few minutes. It gives uniform properties along the coil, a finer grain size, better flatness after the following temper pass, and it is the usual route for grades intended for high-strength forming and for continuous galvanising lines. Because the thermal cycle is short, it demands tighter chemistry control to reach the same formability as batch annealed material.
Full-hard coil skips annealing altogether and is supplied for applications that need stiffness rather than formability, such as certain profiles and bracketry. If a drawing operation fails with splitting at the die radius, confirming the annealed condition is the first check, before tooling adjustments.
Surface Finish, Flatness and Thickness Tolerance
Surface quality is normally specified in two classes: a class A surface free of defects that would affect a visible painted panel, and a class B surface that permits minor defects not affecting formability or coating adhesion. The relevant surface texture is expressed as roughness average Ra and peak count. Bright finish, matt finish and normal finish correspond to different roll texturing, typically Ra values around 0.4 to 1.5 micrometres. Too bright a surface holds paint poorly unless the paint line compensates; too rough a surface shows through thin paint films on exterior panels.
Thickness tolerance for cold rolled strip is defined in EN 10131 in Europe and GB/T 708 in China, with normal and tighter tolerance bands, measured at a specified distance from the edge. A common source of dispute is edge drop: the last few millimetres of a cold rolled coil are thinner than the centre by 1 to 2 percent of nominal gauge. If the customer measures thickness at the very edge of a slit strip, the reading will appear out of tolerance while the coil as a whole conforms.
| Nominal thickness, mm | Normal tolerance, width 600 to 1200 mm | Tighter tolerance band | Typical use of the tolerance class |
|---|---|---|---|
| 0.50 to 0.70 | plus or minus 0.05 | plus or minus 0.03 | Appliance and automotive panels |
| 0.70 to 1.00 | plus or minus 0.06 | plus or minus 0.04 | General press work, enclosures |
| 1.00 to 1.20 | plus or minus 0.07 | plus or minus 0.05 | Structural brackets, roll formed profiles |
| 1.20 to 1.50 | plus or minus 0.09 | plus or minus 0.06 | Chassis parts, furniture frames |
| 1.50 to 2.00 | plus or minus 0.11 | plus or minus 0.08 | Heavier fabricated components |
Flatness is quoted in I-units, where 1 I-unit corresponds to a wave height of 10 micrometres over a wave length of one metre. Good cold rolled coil is delivered within about 10 I-units; 20 I-units or more will cause feeding problems on a progressive die and visible oil-canning on a painted panel. Camber, the deviation of the strip edge from a straight line, is normally limited to a few millimetres over a five-metre length, and square-cut edges are specified separately when the coil is slit.
Temper Rolling, Coil Geometry and Handling Data
Temper rolling, also called skin passing, applies a small elongation of roughly 0.5 to 1.5 percent after annealing. It suppresses the yield point elongation that would otherwise cause stretcher strains, improves flatness, sets the final surface texture and stabilises the mechanical properties so that parts do not change behaviour between coil and coil. Over-tempering is worse than none: beyond about 2 percent elongation the material loses ductility and the gain in surface quality is lost.
Coil geometry matters for the customer's line as much as the metallurgy. Internal diameter is normally 508 mm or 610 mm, outer diameter up to about 2000 mm, coil weight from 3 to 25 tonnes depending on the mill and the handling equipment, and the eye-to-sky direction must be stated because it determines how the coil is unwound on the decoiler. A 610 mm bore delivered to a line with a 508 mm mandrel stops the press, and a 20-tonne coil delivered to a shop with a 10-tonne crane does the same.
Packing for export is a technical choice. Standard sea-worthy packing uses VCI or anti-rust paper, plastic film, steel side plates, circumferential and radial strapping, wooden skids for container loading, and desiccant where the container crosses humid climate zones. The classic claim of white rust or edge rust after a four-week sea voyage is traceable to the interval between oiling and packing and to the humidity inside the container, not to the steel itself.
Inspection, Documentation and Release Criteria
Release of a cold rolled coil shipment should be tied to a defined document set: mill test certificate per EN 10204 type 3.1 for each heat and lot, dimensional inspection record, surface inspection record for the top and bottom side, roughness measurement, coil weight list and packing list. A type 2.2 certificate gives the buyer no independent verification of the values against the cast analysis, whereas a 3.1 certificate is issued by an inspection representative independent of the manufacturing department.
At receiving, a practical acceptance sequence is: verify coil identity and weight against the packing list, measure thickness at a defined point 25 mm or more from the edge, check width and camber over five metres, examine the outer wrap and the first ten metres for edge damage and rust, then cut a short sample for tensile and, where relevant, r and n testing. Recording the inspection position matters, because a dispute about thickness usually turns on where the measurement was taken.
Edge condition deserves its own line in the purchase order. Slit edges can be mill edge, sheared, or deburred; a slit edge with burr above 0.05 mm creates die wear and handling injuries, and a rolled-over burr is not removed by painting. For laser cutting and for exposed edges, deburred or rounded edges are specified separately.
Cost Structure and How to Compare Coil Offers
Cold rolled coil pricing is built from the hot band cost plus the conversion cost of pickling, rolling, annealing, temper rolling and packing. Within that structure the variables a buyer controls are grade, gauge, width, tolerance class, surface class, annealing route, coil weight and packing. A tight tolerance band on a thin gauge and a class A surface both reduce yield at the mill and are legitimately priced higher than commercial quality normal tolerance material.
Offers must be compared on a consistent basis: ex-works or delivered, theoretical or actual weight, tolerance class, edge type, oiling condition, annealing route and whether the certificate is 3.1. A price difference of a few percent between two offers frequently disappears once gauge tolerance is normalised, because a coil rolled to the minus side of a normal tolerance contains measurably less metal per square metre than one rolled to nominal.
FAQ
Q: Is cold rolled steel stronger than hot rolled steel?
Yes in the as-rolled state, and no after annealing. Cold reduction work-hardens the strip to yield strengths of roughly 550 to 700 MPa in full-hard condition, but a normal annealed and temper rolled cold rolled coil is deliberately soft, with yield strength around 140 to 240 MPa depending on grade.
Q: What is the difference between DC01 and DC04?
DC01 is commercial quality with minimum elongation A80 of 28 percent, suitable for bending and roll forming. DC04 is a deep drawing grade with minimum A80 of 38 percent, lower carbon and a plastic strain ratio around 1.6 or higher, which allows deep drawn panels without splitting.
Q: What does full hard mean on a coil certificate?
Full hard means the coil was cold reduced and not annealed. It is used where stiffness matters and forming is limited to gentle bending. It should never be substituted for annealed material in a drawing operation, since its elongation is only a few percent.
Q: Why does the same grade behave differently in the press?
The usual causes are residual stress and flatness differences from the mill, surface roughness differences affecting friction in the die, oil film differences, and grade steps hidden inside a broad specification. Comparing flatness in I-units, roughness Ra, oil mass and r and n values usually explains the discrepancy.
Q: How should thickness be measured on a coil?
At a defined distance from the edge, typically 25 mm or more, using a calibrated micrometer with flat anvils, and at several points along the length. Measuring at the very edge gives a low reading because of edge drop, which is a normal feature of cold rolled strip.
Q: Which packing prevents rust during sea freight?
Anti-rust or VCI paper against the strip surface, a plastic film vapour barrier, steel side and circumference protection, strapping, and desiccant inside the container. The critical control is the dry, oiled condition of the coil at the moment of wrapping, since moisture trapped under the film causes the corrosion.




