Overheating of Weather-Resistant Steel Plate: What Actually Happens Inside the Steel
Weather-resistant plate such as Q355NH to GB/T 4171, S355J0W and S355J2W to EN 10025-5, and Grade A or Grade B of ASTM A588/A588M is a copper-chromium-nickel low-alloy steel designed to form a stable, adherent rust layer that slows further atmospheric corrosion. That corrosion resistance depends on a tightly controlled microstructure, and microstructure is the first thing damaged when a plate is heated beyond its safe window. Overheating is not a single defect: it is a family of related changes, each with its own temperature threshold, its own metallographic signature and its own consequence for toughness, strength and dimensional stability.
For a buyer or a fabricator, the practical question is never whether the plate looks acceptable after rolling. The question is whether the delivered plate still meets the mechanical values declared on the mill certificate, and whether any overheating was severe enough to leave damage that cannot be recovered by a later normalizing treatment. This article sets out the mechanisms, the measurable symptoms, and the acceptance rules that let a purchaser separate cosmetic discolouration from genuine structural degradation.
Where the Heat Comes From: Reheating, Rolling and Fabrication
Overheating in weathering steel plate originates in three places. The first is the reheating furnace before rolling, where slabs are soaked at 1150-1280 degrees C. The second is the finishing pass of hot rolling, where the final deformation is completed at a temperature that determines the austenite grain size entering the transformation. The third is downstream processing: normalizing, stress relieving, hot forming, flame straightening and multi-pass welding of thick sections.
Each stage has a different failure mode. In the furnace, the risk is grain coarsening plus surface and sub-surface oxidation, and in copper-bearing steel also copper-rich liquid embrittlement. During finishing, the risk is a coarse, unrefined austenite that transforms into Widmannstatten ferrite on the run-out table. During fabrication, the risk is grain growth in the heat-affected zone, loss of the micro-alloying pinning that keeps grains fine, and over-tempering of any normalized or thermo-mechanically rolled condition.
Temperature Windows and Grade Reference Data
The table below summarises the temperature thresholds that matter for copper-bearing weathering plate, together with the composition ranges that make the copper-related risk relevant. Values are the industry-typical ranges associated with the standards named in the header row.
| Parameter | GB/T 4171 Q355NH | EN 10025-5 S355J0W / S355J2W | ASTM A588/A588M Gr.A |
|---|---|---|---|
| Carbon, max % | 0.16 | 0.16 | 0.19 |
| Manganese % | 0.50-1.50 | 0.50-1.50 | 0.80-1.25 |
| Copper % | 0.25-0.55 | 0.25-0.55 | 0.25-0.40 |
| Chromium % | 0.40-0.80 | 0.40-0.80 | 0.40-0.65 |
| Nickel % | 0.30-0.60 | 0.30-0.60 | 0.40 max |
| Yield strength, min MPa | 355 at t 16 mm and below | 355 at t 16 mm and below | 345 |
| Typical slab soak temperature | 1180-1260 degrees C | 1180-1260 degrees C | 1180-1260 degrees C |
| Grain coarsening onset, Al-killed plain C-Mn | about 1050 degrees C | about 1050 degrees C | about 1050 degrees C |
| Copper-rich embrittlement risk zone | above 1100 degrees C in oxidizing atmosphere | above 1100 degrees C in oxidizing atmosphere | above 1100 degrees C in oxidizing atmosphere |
Austenite Grain Coarsening: The Root Cause
Grain coarsening is the first and most consequential change. Above a threshold that is set by the steel's micro-alloying and deoxidation practice, austenite grains grow rapidly because the pinning particles that hold the grain boundaries in place either coarsen or dissolve. Aluminium-killed steel without niobium or titanium typically begins to coarsen above roughly 1000-1050 degrees C; additions of niobium, titanium, vanadium, and a controlled aluminium-to-nitrogen ratio push the threshold upward by 50-100 degrees C. This is why two plates that look identical on a certificate can behave very differently after an accidental excursion to 1200 degrees C.
Grain size is not a cosmetic property. The ductile-to-brittle transition temperature of ferrite-pearlite steel moves upward with roughly the inverse square root of the ferrite grain diameter, so doubling the grain size can shift the transition range by tens of degrees. A plate that passes a Charpy V-notch test at 0 degrees C before overheating may fail the same test after grain coarsening, even though its tensile strength and yield strength are unchanged or slightly lower.
Detection is straightforward once the question is asked. Grain size is measured on a polished and etched section per ASTM E112 or the equivalent GB/T 6394 method, reported as a G number or as an average intercept length. A weathering plate delivered in the as-rolled condition should show a ferrite grain size consistent with the declared rolling practice; a sudden coarsening of one to two ASTM grain size numbers below the rest of the heat is a reliable indicator that a portion of the plate saw excessive temperature.
Widmannstatten Ferrite and the Loss of Toughness
When coarse austenite is cooled at a moderate rate, ferrite no longer nucleates only at the prior austenite grain boundaries as equiaxed grains. Instead, plates of ferrite grow along crystallographic planes inside the austenite grain, producing the acicular, basket-weave pattern known as Widmannstatten ferrite. The structure is easy to recognise on a polished and etched cross-section and it is a direct fingerprint of a coarse austenite grain size before transformation.
The mechanical consequence is disproportionate. Widmannstatten ferrite provides a continuous path for cleavage crack propagation across what were once individual grains, and its interlath regions act as brittle links. Impact energy at low temperature falls sharply, notch ductility deteriorates, and the plate may show brittle fracture initiation at stresses far below the design value during flame cutting, bending or welding. Unlike grain coarsening alone, Widmannstatten ferrite cannot be removed by stress relieving; it requires a full re-austenitizing normalizing treatment followed by air cooling, and even then only if the section is thin enough to cool uniformly.
Copper-Rich Embrittlement in Copper-Bearing Weathering Steel
This is the overheating mode that is specific to weathering grades and is therefore the one most often missed. All of the weathering standards deliberately alloy copper at 0.25-0.55 per cent to promote the protective rust layer. Copper has very limited solubility in austenite at high temperature, and in an oxidizing furnace atmosphere the surface layer becomes enriched in copper as iron is preferentially oxidized. Once the enriched zone exceeds the solubility limit at the soaking temperature, a copper-rich liquid film forms at austenite grain boundaries, and the steel loses ductility exactly where it is being rolled.
The visible result is surface cracking, closely spaced transverse or network cracks on the plate surface, often described as hot shortness or surface crazing. Nickel is the standard countermeasure: a nickel-to-copper ratio approaching or exceeding one to one raises the solubility of copper in austenite and suppresses liquid film formation. This is why ASTM A588 Grade A permits only 0.40 per cent nickel while other weathering specifications allow 0.30-0.60 per cent, and why plate rolled from high-residual scrap without nickel adjustment is more vulnerable. For a purchaser, the practical rule is to treat a heat with copper above 0.40 per cent and nickel below 0.25 per cent as one that needs a controlled, lower soak temperature and a shorter residence time in the furnace.
Residual Austenite and Dimensional Instability
In copper-bearing and micro-alloyed plate, overheating before an accelerated cool, or overheating followed by an inadequate temper, leaves retained austenite in the structure. Retained austenite is metastable: it transforms to martensite under strain or over time, accompanied by a volume increase of a few per cent locally. The consequences are progressive, which makes them dangerous. A flame-cut part may be dimensionally correct at delivery and move several tenths of a millimetre after machining, and the same transformation can initiate micro-cracks at grain boundaries.
Where a plate has been quenched and tempered after overheating, the coarser prior austenite grain size also produces coarser martensitic packets. Coarse packets raise the ductile-to-brittle transition temperature and increase the risk of quench cracking, because the transformation stresses act over longer distances. In practice this means that an overheated plate cannot be rescued simply by quench and temper; the prior austenite grain size must be restored first by normalizing.
Detecting and Quantifying Overheating: A Practical Test Sequence
A credible investigation follows a fixed sequence rather than a single test. Start with dimensional and surface inspection: measure thickness across the plate, look for transverse surface cracking, and check for a coarse, blistered or heavily scaled surface that suggests an excessive soak. Then take a transverse section for metallography and record three things: prior austenite grain size where it can be revealed, ferrite morphology including any Widmannstatten content, and decarburization depth.
Mechanical verification follows. Tensile testing per ISO 6892-1 or ASTM A370 confirms that yield and tensile strength still bracket the specification range; Charpy V-notch impact testing per ISO 148-1 at the grade's specified temperature confirms that toughness has not been lost; and a bend or flattening test reveals surface ductility problems that tensile testing misses. For thick plate, through-thickness hardness traverses identify local hard spots caused by retransformed martensite. Where the plate is intended for a welded structure, hardness mapping of a procedure qualification coupon gives the most useful early warning, since a heat-affected zone that exceeds 350 HV10 in a non-hardening grade indicates either excessive heat input control failure or an abnormal base chemistry.
Corrosion performance should also be re-checked after any thermal excursion. The protective rust layer of weathering steel depends on the alloying elements remaining in solid solution at the surface. Heavy scaling removes the enriched layer, and decarburization changes the local chemistry. A salt spray test per ASTM B117 or a cyclic corrosion test evaluated against the corrosivity categories of ISO 9223 is a reasonable screening tool; the wet-dry cyclic approach described in ASTM G101 is closer to real atmospheric exposure and is the better basis for judging whether the patina will still form.
Corrective Heat Treatment and Rolling Practice
Not every overheated plate is scrap. The deciding question is whether the damage is confined to a surface layer or extends through the section. Surface decarburization and light copper enrichment can be removed by grinding or machining to a depth established by metallography. Grain coarsening and Widmannstatten ferrite that extend through the thickness require full normalizing: reheating to a temperature high enough to re-dissolve and re-precipitate the micro-alloying phases, holding long enough for uniformity, and air cooling. For structural weathering grades the practical normalizing range is roughly 890-940 degrees C, with the exact value chosen so that the plate stays well below the grain coarsening threshold of that particular chemistry.
Prevention is cheaper. Furnace practice should cap the soak temperature for copper-bearing weathering steel at the lowest value that still guarantees a fully austenitic slab, and residence time should be the minimum consistent with temperature uniformity. Finishing temperature should be controlled so that the final passes leave a refined austenite, and accelerated cooling should start at a temperature that avoids both excessive ferrite coarsening and hard martensite formation. On the fabrication side, heat input during welding and flame straightening should be limited, and localized heating above roughly 650 degrees C on a normalized or thermo-mechanically rolled plate should be treated as a change to the delivered condition requiring metallurgical verification.
FAQ
Q: At what temperature does weathering steel plate start to suffer permanent damage?
For most copper-bearing structural weathering grades, grain coarsening begins above about 1050 degrees C and copper-rich surface embrittlement becomes a real risk above roughly 1100 degrees C in an oxidizing furnace atmosphere, so any excursion above 1100 degrees C needs metallographic verification.
Q: Can Widmannstatten ferrite be removed by stress relieving?
No. Stress relieving at 550-650 degrees C relieves residual stress but does not re-austenitize the steel, so the acicular ferrite and the coarse prior austenite grain boundaries remain; only a full normalizing treatment above the A3 temperature can restore a refined structure.
Q: Why is copper a problem in weathering steel when it is added on purpose?
Copper at 0.25-0.55 per cent is beneficial in service because it promotes a protective rust layer, but at soaking temperatures the solubility of copper in austenite is low, so an oxidizing atmosphere can enrich the surface to the point of forming a liquid copper-rich film at grain boundaries and causing hot shortness.
Q: Which tests best reveal overheating in a delivered plate?
A transverse metallographic section reporting prior austenite grain size, ferrite morphology and decarburization depth, combined with Charpy V-notch impact testing at the grade's specified temperature and a through-thickness hardness traverse, gives the most reliable picture of whether the plate has been damaged.
Q: Does overheating show up in the tensile test?
Often it does not. Yield strength and tensile strength may remain inside the specification range or even fall slightly, while impact toughness at low temperature drops sharply, which is why Charpy testing and metallography rather than tensile testing alone are the decisive checks.
Q: What nickel content protects against copper-related overheating damage?
The industry rule of thumb is that nickel should approach copper on a one-to-one basis; grades that cap nickel at 0.40 per cent, such as ASTM A588 Grade A, rely on controlled furnace temperature and short soak times rather than on nickel for protection.




