What are common testing requirements for S890Q ?
Common testing for S890Q steel involves mandatory tensile tests (yield/tensile strength, elongation) and Charpy V-notch impact tests (typically at -20°C for 30J) per heat/batch, conforming to EN 10025-6, along with heat analysis, with optional ultrasonic testing (UT) or product analysis. Tests are done on longitudinal specimens (impact) or transverse (tensile for thinner plates), ensuring mechanical properties and chemical composition meet standards for this high-strength, quenched & tempered steel used in heavy machinery and structures.

S890Q is a fluid-tempered high strength weldable fine grained steel with a min. yield point of 890 N/mm². It is applicated for high loaded steel constructions, vehicles, lifting, mining equipment. The usual thickness range amounts 3 to 100 mm. The lowest application temperature accounts for -20°C. The steel is processed by cold forming, at temperatures below the highest permissible stress relieving temperature of 530 to 580 °C. After hot forming at 700 to 1050°C has to be coducted a retempering in order to achieve delivery condition qualities. The steel is combustible and electric arc cuttable subject to appropriate mode of operation. Flame cutting is affected by the surface condition. For product thicknesses above 30 mm is advisable a preheating to 100 to 200 °C in order to assure cold crack resistance. Preheating to 100 to 200 °C is advisable for workpiece temperatures below 5 °C and if the thermal cut edges should be cold formed on processing. Instructions: The steel is suitability tested for the construction of pressure vessels and pressure pipes according to the regulations valid in Germany (VdTÜV-material data sheet 417).
Key Characteristics:
High Strength: Minimum yield strength of 890 N/mm² (MPa).
Quenched & Tempered (Q): Heat-treated for enhanced strength and toughness, making it weldable.
Fine-Grained: Refers to its microstructure, contributing to its toughness.
High-Performance Applications: Ideal for extreme load conditions in construction, vehicles, lifting equipment, and offshore structures.
Notation Breakdown:
S: Structural steel.
890: Minimum yield strength in MPa.
Q: Quenched and tempered delivery condition.
Production Size: Thickness: 4mm- 400mm; Width: 1000mm- 4000mm; Length: 4000mm- 12000mm.
Production ability:10000 Tons Per Month.
Production Way: Hot Rolled, Quenched( Q).
S890Q is an ultra-high-strength, quenched, and tempered structural steel (EN 10025-6) used in heavy-duty applications for weight reduction and high load capacity, finding use in heavy construction machinery, cranes, bridges, offshore structures (rigs, wind turbines), and transport vehicles that need excellent toughness, strength (minimum yield 890 MPa), and good weldability with proper pre-heating.

What are the primary advantages of S890Q ?
S890Q's primary advantages are its exceptional high yield strength (≥890 MPa) and excellent toughness, enabling significant weight reduction, cost savings (due to less material, transport), greater design freedom (thinner elements, longer spans), and improved performance in heavy-load applications like cranes, bridges, and heavy machinery, despite needing careful handling during welding due to its high strength.
Is S890Q high speed steel?
No, S890Q is not a high-speed steel; it's a high-strength quenched and tempered (Q&T) structural steel, designated by the European standard EN 10025-6, known for its minimum yield strength of 890 MPa, making it ideal for heavy machinery, bridges, and construction where toughness and load-bearing capacity are critical, unlike high-speed steels (HSS) which are tool steels for cutting at high temperatures.
What is the hardness of S890Q ?
S890Q is a high-strength structural steel with a minimum yield strength of 890 MPa, delivered in a quenched and tempered (Q) condition, but its specific hardness (Brinell or Rockwell) isn't a single fixed number; it's typically very high, often around 260-320 HBW (Brinell) or higher, depending on the exact thickness and supplier, reflecting its extreme strength, with values generally exceeding 900 MPa tens
|
S890QChemical Composition |
||||||||
|
Grade |
The Element Max (%) |
|||||||
|
C |
Si |
Mn |
P |
S |
N |
B |
Cr |
|
|
S890 Q |
0.20 |
0.80 |
1.70 |
0.020-0.025 |
0.010-0.015 |
0.015 |
0.005 |
1.50 |
|
Cu |
Mo |
Nb |
Ni |
Ti |
V |
Zr |
|
|
|
0.50 |
0.70 |
0.06 |
2.0 |
0.05 |
0.12 |
0.15 |
||
|
Grade |
S890Q Mechanical Property |
|||||
|
Thickness |
Yield |
Tensile |
Elongation |
Min Impact Energy
|
||
|
S890 Q |
mm |
Min Mpa |
Mpa |
Min % |
-20 |
30J |
|
3 |
890 |
940-1100 |
11 |
-20 |
30J |
|
|
50 |
830 |
880-1100 |
11 |
-20 |
30J |
|
|
100 |
800 |
820-1000 |
11 |
-20 |
30J |
|
1What is the maximum allowable stress value for S890Q ?
S890Q is a high-strength structural steel with a minimum yield strength of 890 MPa (129 ksi) and tensile strength typically between 940-1100 MPa, but the allowable stress depends on the specific design code (like Eurocode or AISC), safety factors, thickness, and application, usually found by dividing yield strength by a safety factor (e.g., around 500-600 MPa for general structural design), so always check the relevant design code for your project.
2What is the composition of S890Q ?
S890Q is a high-strength, weldable fine-grained structural steel (EN 10025-6 standard) quenched and tempered for high-load applications, with a typical composition including maximums for Carbon (C), Phosphorus (P), Sulfur (S), and smaller additions of Silicon (Si), Manganese (Mn), Chromium (Cr), Molybdenum (Mo), Nickel (Ni), Vanadium (V), Copper (Cu), Aluminum (Al), Niobium (Nb), and Titanium (Ti) to achieve properties like 890 MPa yield strength. Key elements are generally limited to ~0.20% C, ~0.80% Si, ~1.70% Mn, ~0.025% P, and ~0.015% S, with alloying elements like Mo, Cr, Ni, and V providing strength.
3What are common testing requirements for S890Q ?
Common testing for S890Q steel involves mandatory tensile tests (yield/tensile strength, elongation) and Charpy V-notch impact tests (typically at -20°C for 30J) per heat/batch, conforming to EN 10025-6, along with heat analysis, with optional ultrasonic testing (UT) or product analysis. Tests are done on longitudinal specimens (impact) or transverse (tensile for thinner plates), ensuring mechanical properties and chemical composition meet standards for this high-strength, quenched & tempered steel used in heavy machinery and structures.
4What are the typical application fields of S890Q ?
S890Q is a high-strength, quenched and tempered structural steel used in applications demanding extreme loads, such as heavy machinery (mining, construction, lifting equipment), transportation, bridges and trestles, and the offshore industry (wind turbine supports, drilling rigs). Its high yield strength (890 MPa) and excellent weldability make it ideal for highly stressed components in sectors like engineering, automotive, and agriculture.
5What is S890Q equivalent to?
S890Q is a European high-yield strength structural steel (EN 10025-6) with a minimum yield strength of 890 MPa, often equivalent to Chinese Q890 steel, and is used for heavy-duty applications, with variations like S890QL (for -50°C impact) and S890QL1 (for -60°C impact) also available, similar in function to other quenched and tempered (Q&T) high-strength steels.
6What welding rod for S890Q ?
For welding S890Q high-strength steel, you need a high-strength filler metal matching its yield strength (890 MPa), with common choices including TIG rods like ER120S-1 (AWS A5.28, EN ISO 16834-A: W 89 5 I1 Mn4Ni2CrMo) or stick electrodes such as E9018-M or equivalent high-strength low-alloy (HSLA) types, designed for quenched & tempered steels, ensuring excellent toughness and mechanical properties, often with Nickel/Molybdenum/Chromium alloying. Always follow codes (like AWS/ASME) and manufacturer guidelines for preheat/PWHT.
7What is the P number of S890Q ?
For S890Q high-strength structural steel, the P-number in welding (per ASME/AWS standards) typically places it in P-Number 1 (P1), as it's a low-alloy, quenched and tempered steel, often grouped with other carbon steels, though sometimes specific P-numbers like P91 might apply for higher-alloy versions, but standard S890Q falls into the general P1 category for its basic composition.
For more details about GNEE's steel products, contact us at info@gneesteels.com . We look forward to working with you.





