What the AH32 Grade Designation Tells You Before Surface Quality Is Even Discussed
AH32 is a high-strength hull structural steel defined by ASTM A131/A131M and reproduced in GB/T 712, with each classification society - ABS, CCS, DNV, BV, LR, NK, RINA and others - issuing its own rule text that adds inspection and marking requirements on top of the material standard. The letters are not decorative. The A denotes the impact test temperature band, with A tested at 0 degrees Celsius, D at minus 20, E at minus 40 and F at minus 60. The H marks a high-strength rather than normal-strength grade. The 32 is the minimum specified yield strength in kilograms-force per square millimetre, which corresponds to 315 MPa in SI units.
Surface quality cannot be judged in isolation from that designation, because the same visual feature is treated differently depending on where it sits, how deep it goes and what the plate is going to be used for. A shallow roll mark on the outer bottom shell of a bulk carrier and the same mark on a 12 mm deck plate in a stress concentration are not the same nonconformity. Classification surveyors judge surface condition against the plate thickness, the structural location and the repair that would be needed, which is why the requirement is written as a set of rules about depth, blending and remaining thickness rather than as a simple list of forbidden features.
For a buyer, the practical takeaway is that surface quality must be specified as a document chain rather than as an adjective. The order needs a material standard, a society rule, a repair policy, an inspection level and a certificate type. Without those five elements, the phrase good surface quality is unenforceable at receipt.
The Document Chain That Actually Governs Surface Acceptance
Four layers of documents apply to a delivered AH32 plate, and they are not interchangeable. The material standard, ASTM A131/A131M or GB/T 712, fixes the chemistry, mechanical properties and general delivery condition. The classification society rules fix the survey, the stamping and the additional requirements that a shipyard actually needs to obtain class approval for the hull. The general surface quality standard, in Chinese practice GB/T 14977 for hot-rolled plate, supplies the default definitions and permissible repair depths where the society rule is silent. The purchase order supplies everything the three above leave open, including thickness tolerance class, flatness, ultrasonic testing level and the acceptable amount of mill scale.
Where these documents conflict, the more restrictive one governs, and the society rule normally wins over the material standard because the vessel will be surveyed against the rule, not against the standard. This matters in practice at the point of repair: a grinding repair that is acceptable under a general mill standard may still be rejected by a surveyor if it falls in a region the rule treats as critical, or if the repaired area exceeds the proportion of plate surface the rule allows.
The certificate closes the chain. A plate intended for hull construction should arrive with an inspection certificate to EN 10204 type 3.1 at minimum, specific to the heat, and for higher-grade or thicker material often type 3.2 with independent verification. The certificate must carry the society's endorsement, the heat number, the grade and the mechanical test results; a certificate that names the grade but not the society is not evidence of class approval.
Defects That Are Not Accepted on an AH32 Plate
The prohibited list is short and consistent across societies and general plate standards. Cracks of any orientation are unacceptable and may not be repaired by grinding without specific approval, because a crack indicates a through-thickness or near-through-thickness discontinuity rather than a surface blemish. Blisters, which are gas pockets rolled into the surface, are unacceptable because they conceal a lamination beneath. Seams, laps and folds - overlapping metal formed during rolling - are unacceptable because they trap oxide and act as crack initiators under cyclic loading. Scabs, which are rolled-in splashes of steel or heavy scale, are unacceptable because removing them usually reveals a depression deeper than the plate tolerance allows.
Laminations are in a separate category. They are internal rather than surface defects, but they reveal themselves at cut edges as a straight split parallel to the surface, and once visible they are not repairable. A plate showing edge laminations should be rejected outright, and the appropriate response is ultrasonic testing of the remainder of the heat rather than local dressing.
Other features are tolerated within limits rather than forbidden. Rolled-in scale, light pitting, handling indentations, roll marks, minor scratches and colour variation from the cooling bed are normal in as-rolled plate and are accepted provided they do not reduce the thickness below the permitted minimum and do not form sharp-bottomed notches. The distinction that a surveyor applies is whether the feature is a stress raiser or a thickness reduction; a shallow smooth depression is tolerable, a sharp-edged gouge of the same depth is not.
Grinding Repair: Depth Limits, Blending and Remaining Thickness
Grinding is the standard remedy for shallow surface defects and is permitted within defined limits. Three conditions must be satisfied simultaneously. First, the ground depth must not reduce the plate below the minimum thickness allowed by the applicable thickness tolerance, which in practice means the original thickness minus the permitted negative deviation at that point. Second, the ground area must be blended so that no step or shoulder remains, with a taper commonly specified at about one in five to one in six from the bottom of the depression to the original surface; a steep-walled depression is itself a notch and is worse than the defect it removed.
Third, the extent of repair is limited. Societies typically restrict the proportion of plate surface that may be dressed, and restrict or prohibit repairs in defined zones such as areas that will be cold-formed, areas adjacent to welded connections, and the region within a set distance of the plate edge. The exact percentages and distances belong to the individual rule and must be read from the applicable society text rather than assumed from a general standard.
After grinding, the repaired area should be inspected visually and, where the repair is deep or the plate is destined for a critical location, by magnetic particle or dye penetrant testing to confirm that no crack remains at the bottom of the depression. A ground area that still shows a linear indication has not been repaired; it has been exposed, and the plate should then be rejected or referred to the surveyor for a decision.
Weld Repair and Why It Needs Approval
Welding is not a permitted method of correcting surface defects on hull structural plate unless the classification society has approved the procedure for that specific case. The reason is metallurgical: a local weld deposit on a 315 MPa minimum yield hull steel creates a hard heat affected zone, a residual stress field and a new inspection obligation, and the repair may be made in a region where the plate will later be cold-formed or welded into a highly restrained joint. Unauthorised weld repair that is later detected leads to rejection of the plate and, in the worst case, to a survey finding against the vessel.
Where weld repair is approved, the procedure normally requires removal of the defect to sound metal before welding, a qualified procedure and qualified welders, low-hydrogen consumables, preheat appropriate to the composition and thickness, and post-repair inspection by magnetic particle or penetrant testing plus ultrasonic testing where the depth warrants it. The repair is recorded, and the record forms part of the plate documentation.
For the buyer, the commercial implication is that weld repair should be treated as an exception requiring written agreement, not as a routine workshop remedy. A supplier who offers to weld-fill surface defects on class plates without a surveyor in the loop is offering a shortcut that the shipyard will pay for later.
Delivery Condition, Scale and Surface Preparation Before Painting
AH32 plate is normally supplied as-rolled, normalized or in a thermomechanically controlled rolled condition depending on thickness, mill capability and society approval. The delivery condition affects the surface as much as the properties: normalizing produces a more uniform, thinner and more adherent scale than as-rolled material, while accelerated cooling can leave a darker, tighter oxide layer. Neither condition is a defect, but both determine how much surface preparation is needed before coating.
Mill scale is not a protective coating. It is brittle, it cracks under impact, and it shelters an oxygen concentration cell that accelerates corrosion at every break. Coating specifications therefore require abrasive blast cleaning to the grades defined in ISO 8501-1, typically Sa 2.5 for hull externals and internal ballast tanks, followed immediately by a primer. A plate delivered with heavy, flaking scale costs the shipyard more in blasting time and abrasive consumption than a plate delivered with a light, tight scale, and this is a legitimate point to raise at order stage.
Where a shop primer is applied at the mill or at the steel service centre, the dry film thickness is usually specified in the 15 to 25 micrometre range and must be compatible with the subsequent coating system, including any weld-through requirement. Excessively thick primer causes porosity in welds; primer that is too thin leaves the plate unprotected during transport and storage. Both are surface quality issues that surface after the plate has left the mill, which is why the coating specification belongs in the purchase order rather than in a later conversation.
How Surface Quality Interacts With Thickness and Flatness Tolerances
Surface judgement is inseparable from dimensional judgement, because almost every surface defect is evaluated by how much metal it removes. A depression that is 0.5 mm deep on a 30 mm plate is irrelevant; the same depression on an 8 mm plate consumes a meaningful share of the permitted thickness tolerance. This is why the same visual standard produces different verdicts on different plate sizes and why the acceptance decision must always be made with the thickness tolerance table open alongside the surface defect.
Thickness is measured at a defined number of points, away from edges and away from any dressed area, and the minimum reading governs. For plates ordered to a normal hot-rolled tolerance, the permitted negative deviation at nominal thickness is small but not zero, and a plate that has been heavily dressed to remove scale or scabs can fall outside it. Flatness is judged separately, usually against a flatness class agreed at order, and local buckles caused by uneven cooling are not surface defects but are frequently confused with them at receipt.
Edges deserve explicit attention in the same inspection pass. Shear burr, torch roughness and edge cracks are all surface conditions in the sense that matters to a shipyard, since the edge is where fit-up and welding start. Edge cracks are never acceptable, and a plate showing them should be referred for ultrasonic examination before any decision is made about trimming.
The AH32 Family Compared: What Changes With Impact Grade
Surface requirements are common across the AH, DH, EH and FH variants, but the mechanical requirements are not, and buyers frequently conflate the two. The table below summarises the typical envelope for the 32 kg class; values must be confirmed against the applicable standard and society rule for the thickness in question.
| Grade | Impact test temperature | Minimum yield strength (MPa) | Tensile range (MPa) | Minimum elongation (%) | Typical carbon equivalent limit (%) | Typical service |
|---|---|---|---|---|---|---|
| AH32 | 0 degrees C | 315 | 440 - 590 | 22 | 0.36 | Upper deck, superstructure, general hull |
| DH32 | Minus 20 degrees C | 315 | 440 - 590 | 22 | 0.36 | Side shell, inner bottom, moderate climate |
| EH32 | Minus 40 degrees C | 315 | 440 - 590 | 22 | 0.36 | Sheer strake, bilge, cold water service |
| FH32 | Minus 60 degrees C | 315 | 440 - 590 | 22 | 0.36 | Ice-class and Arctic service |
Charpy requirements for these grades are expressed as a minimum average energy from three specimens, commonly 31 J with individual values not below about 70 percent of that average, tested at the grade temperature. The distinction between AH32 and DH32 is therefore not strength but toughness at temperature, and a plate that passes AH32 impact testing is not evidence that a DH32 requirement can be met from the same heat.
Carbon equivalent is normally capped at about 0.36 for the 32 class in the thicknesses used for hull construction, with some rules permitting a higher value for heavier plate subject to weldability verification. Silicon is typically 0.10 to 0.50 percent, manganese 0.90 to 1.60 percent, phosphorus and sulphur are held low, and a fine grain practice with aluminium or niobium, vanadium or titanium additions is required so that the impact energy at the grade temperature is actually achievable.
Inspection Workflow From Mill to Stockyard
Surface inspection happens three times, and each pass answers a different question. At the mill, the plate is inspected on the cooling bed and after levelling for rolling defects, and any dressing is carried out before the plate is marked. At the society survey, the plate is examined for the features that affect class approval, the heat identification is verified, and the stamp is applied. At receipt in the shipyard or stockyard, the question changes to whether the plate has survived transport and storage without new damage.
The receipt inspection should follow a fixed sequence: verify the stamp and the certificate, check the heat number on the plate against the certificate, measure thickness at the agreed points, check flatness, then walk the surface under adequate oblique lighting. Oblique light is important; a defect that is invisible under diffuse light becomes obvious when the light is raked across the surface at a shallow angle. Any indication that could be a crack should be confirmed by magnetic particle testing before the plate is released to production.
Damage found at receipt is a claim, not a repair. Handling marks, crane-clamp indentations, gouges from forks and rust bloom from poor storage are all chargeable against the supplier or the carrier, and the window for claiming closes as soon as the plate is cut. Photographing the plate with the stamp visible, before any cutting, is the single most useful habit in this process.
Storage and Handling: Where a Good Surface Goes Bad
AH32 plate stored outdoors without support will distort, pond water and develop rust grades that require full blasting before use. Plates should be stacked on timber or concrete bearers at adequate spacing, with the stack tilted very slightly or with drainage gaps, and should never be stored in contact with the ground or with dissimilar metals that set up galvanic corrosion at the contact line.
Lifting practice matters as much as storage layout. Wire slings without softeners leave deep score marks that are difficult to distinguish from cracks and that must be dressed before the plate can be accepted, and magnetic lifting beams can leave local magnetisation that interferes with subsequent magnetic particle inspection. Plate separators should be used to avoid dragging plates across each other, which produces long shallow scratches that mimic seams.
Where plates are stored for extended periods before fabrication, a condition monitoring routine is cheaper than remedial blasting. A monthly visual check for rust grade progression, standing water and edge corrosion, combined with re-application of protective coating on damaged areas, keeps the plate within the surface condition the coating specification assumes.
Putting the Requirement Into a Purchase Order
A workable order specification for AH32 plate names the material standard and revision, the classification society and the rule edition, the thickness and tolerance class, the flatness class, the delivery condition, the ultrasonic testing level and extent, the certificate type, the marking requirements and the repair policy. It states explicitly that weld repair is not permitted without written approval, and it defines the acceptance criteria for surface condition by reference to the standard and rule rather than by description.
It should also fix the commercial consequences. Agree who pays for blasting if the scale condition is heavier than the sample approved at order, who bears the cost of a rejected plate and its return freight, and what inspection access the buyer has at the mill before shipment. These are the terms that determine whether a surface quality clause is a working document or a sentence nobody reads until there is a dispute.
FAQ
Q: Are cracks on an AH32 plate ever acceptable if they are shallow?
No. Cracks are not repairable by grinding without specific classification society approval, because they indicate a discontinuity deeper than the visible surface. The plate should be referred to the surveyor, and the surrounding material should be examined by magnetic particle or ultrasonic testing.
Q: What does the A in AH32 mean?
The A denotes the impact test temperature band, with A tested at 0 degrees Celsius, D at minus 20, E at minus 40 and F at minus 60. The H indicates a high-strength grade and 32 indicates a minimum yield strength of 315 MPa.
Q: How deep may a surface defect be ground out?
Deep enough to remove the defect, but never so deep that the remaining thickness falls below the minimum permitted by the thickness tolerance, and the depression must be blended with a taper of roughly one in five to one in six. The proportion of plate surface that may be dressed is limited by the applicable society rule.
Q: Is mill scale considered a surface defect?
Mill scale is not a defect and is not cause for rejection, but it is not a protective coating either. Heavy or flaking scale increases blasting time and must be removed to the grade required by the coating specification, typically Sa 2.5 of ISO 8501-1.
Q: Can weld repair be used to fill a rolled-in scab?
Only with prior written approval from the classification society and a qualified procedure. Unapproved weld repair on hull structural plate is a common cause of rejection at survey, and the repair record becomes part of the plate documentation.
Q: What certificate should accompany a class-approved AH32 plate?
At minimum an EN 10204 type 3.1 inspection certificate specific to the heat, carrying the society endorsement, the heat number, the grade and the mechanical test results. Thicker or higher-grade material is often ordered with type 3.2 independent verification.




