Dec 05, 2025 Leave a message

A573 Grade 70 Steel: Typical Applications

1. What Is A573 Grade 70?

ASTM A573 covers carbon-manganese-silicon steel plates of improved toughness, intended for pressure vessel and general structural service. The grades are numbered by their minimum tensile strength: Grade 58, Grade 65 and Grade 70. Grade 70 is the highest-strength member, with a minimum yield of 290 MPa (42 ksi) and a tensile range of 485–620 MPa (70–90 ksi). The controlled carbon, manganese and silicon levels give the plate good weldability, while the toughness makes it suitable for welded pressure-containing and load-bearing structures.

2. Mechanical Properties

The key values for A573 Grade 70 are:

Property Value
Minimum yield strength 290 MPa (42 ksi)
Tensile strength 485–620 MPa (70–90 ksi)
Elongation per ASTM A573, thickness- and gauge-length-dependent
Density about 7.85 g/cm3

Typical plate thicknesses supplied range from about 6 to 150 mm, but this is a supply range rather than a standard requirement.

3. Main Application Areas

A573 Grade 70 is used in several overlapping fields. Pressure vessels: welded tanks, process vessels and industrial pressure containers benefit from the combination of strength and ductility. Storage tanks: oil, chemical and fuel tanks use the plate for its toughness and integrity in large welded structures. Structural components: support beams, frames, stiffeners and heavy load supports use its strength-to-weight efficiency. Construction equipment: crane parts, lifting equipment and heavy-duty frames exploit the high tensile strength. Bridge fabrication: girders, diaphragms and structural plates are welded reliably in large sizes. Energy and power: hydropower steel structures and turbine housings rely on its toughness and structural reliability.

4. Why the Grade Fits These Applications

The material's usefulness follows directly from four properties. High tensile strength allows it to handle heavy loads, pressure and stress. Good weldability suits it to large welded vessels and structures, with a moderate carbon content that limits hardening and cracking. Reliable toughness lets it withstand cyclic loads and structural stress. Balanced ductility reduces cracking risk during welding, which matters for fabricators working with thick plates and restrained joints.

5. Welding Recommendations

A573 Grade 70 can be welded by SMAW, GMAW, FCAW, SAW and GTAW. Because it is a higher-strength steel, good practice is required. For thin plates below about 25 mm, preheat is usually minimal or not required; for thicker plates, a preheat of 50–100°C is commonly recommended to prevent hydrogen cracking. Heat input should be controlled and the interpass temperature kept below about 200°C to preserve toughness. SAW is especially suitable for thick plates, and GTAW is a good choice for root passes.

Frequently Asked Questions

What is the yield strength of A573 Grade 70? minimum of 290 MPa (42 ksi) per ASTM A573/A573M, with a tensile range of 485–620 MPa (70–90 ksi).

Is A573 Grade 70 weldable? Yes. The moderate carbon and controlled manganese and silicon levels give good weldability with common processes; preheat of 50–100°C is recommended for thick sections.

What is A573 Grade 70 used for? Welded pressure vessels, storage tanks, heavy structural components, construction equipment, bridge parts and energy sector structures.

How does A573 Grade 70 differ from A516? 516 is the pressure-vessel carbon plate standard with specified Charpy toughness classes, while A573 emphasizes improved toughness with grades defined by tensile strength; the correct choice depends on the code requirements.

Does A573 Grade 70 require impact testing? Impact testing applies when the specification or code requires it; A573 is selected for toughness, but the Charpy requirement must be confirmed for the project.

What welding processes are suitable? SMAW, GMAW, FCAW and SAW are all suitable; GTAW is good for root passes, and SAW suits thick plates.

Send Inquiry

whatsapp

phone

Email

Inquiry