What 42CrMo Is, and What It Is Not
42CrMo is a chromium-molybdenum alloy structural steel defined in GB/T 3077, the Chinese standard for alloy structural steels. Its European counterpart is 42CrMo4 in EN 10083-3, the standard for quenched and tempered steels, and its closest American equivalent is 4140 as covered by ASTM A29/A29M for hot wrought steel bars. All three describe a medium-carbon, chromium-molybdenum steel with roughly 0.4 percent carbon, 1 percent chromium and 0.2 percent molybdenum, and all three are supplied in the quenched and tempered condition for high-stress mechanical components.
A frequent classification error in trading documents is to describe this grade as die steel or tool steel. It is neither. It belongs to the alloy structural steel family, and its properties are developed by a hardening and tempering treatment rather than by the wear resistance and hot hardness expected of tooling grades. The confusion matters commercially, because a buyer who specifies a tool steel will expect hardness levels and a heat treatment response that this grade does not deliver, and a supplier who accepts the description may ship a material that fails on dimensional stability or through-hardening.
The chemistry is deliberately balanced. Chromium raises hardenability and provides some resistance to scaling and to mildly corrosive environments; molybdenum suppresses temper embrittlement and further increases hardenability so that thick sections can be through-hardened; manganese and silicon act as deoxidisers and contribute to strength. The result is a grade that hardens deeply, tempers predictably and holds a wide range of strength levels from a single composition.
Chemical Composition Across Standards
The three specifications are close but not identical, and the differences matter when a drawing references one standard while the mill certificate reports another. The manganese range is the widest divergence, and manganese has a strong effect on hardenability, so a 4140 bar and a 42CrMo4 bar of the same diameter do not necessarily respond identically to the same quench.
| Element (%) | 42CrMo, GB/T 3077 | 42CrMo4, EN 10083-3 | 4140, ASTM A29/A29M |
|---|---|---|---|
| C | 0.38 - 0.45 | 0.38 - 0.45 | 0.38 - 0.43 |
| Si | 0.17 - 0.37 | 0.40 max | 0.15 - 0.35 |
| Mn | 0.50 - 0.80 | 0.60 - 0.90 | 0.75 - 1.00 |
| P | 0.035 max | 0.025 max | 0.035 max |
| S | 0.035 max | 0.035 max | 0.040 max |
| Cr | 0.90 - 1.20 | 0.90 - 1.20 | 0.80 - 1.10 |
| Mo | 0.15 - 0.25 | 0.15 - 0.30 | 0.15 - 0.25 |
| Ni / Cu | 0.30 max each | residual limits apply | residual limits apply |
Two purchasing points follow from the table. First, a certificate that reports molybdenum at 0.15 percent and chromium at 0.90 percent sits at the low end of the specification and will show a shorter hardenability curve than one at the middle of the range; for large sections this is a real difference in the hardened depth, not a rounding detail. Second, phosphorus control separates the European specification from the other two. Where a component operates in a temperature range that promotes temper embrittlement, the stricter phosphorus limit is the reason to specify the EN grade rather than to accept a generic 42CrMo.
Residual elements deserve a line on the purchase order as well. Copper above about 0.30 percent and tin above about 0.05 percent raise the risk of surface cracking during hot working and reduce toughness, and these residuals accumulate when scrap-based steelmaking is used. A mill certificate that reports only the specified elements and omits residuals leaves the buyer unable to judge that risk.
Mechanical Properties in the Quenched and Tempered Condition
For 42CrMo, GB/T 3077 tabulates properties for the quenched and tempered condition at a defined reference section size: minimum tensile strength 1080 MPa, minimum yield strength 930 MPa, minimum elongation 12 percent, minimum reduction of area 45 percent, and a delivered hardness not exceeding 217 HBW. Those figures are the reference block, not a guarantee for every section.
The section size effect is the most under-appreciated property of this grade. The tabulated values apply to a small reference specimen. A round bar of 200 mm diameter quenched in oil will not reach the same core properties as a 40 mm bar, because the centre cools too slowly to transform fully to martensite, and the resulting microstructure is a mixture of martensite, bainite and ferrite. Property testing on a separately heat treated small specimen can therefore pass while the actual component core does not. Where through-thickness properties govern the design, the order should specify the hardness or microstructure requirement at a defined depth below the surface of the actual section, or require test bars taken from a prolongation of the same section.
Charpy impact values are also section dependent and are not freely interchangeable between standards. If a design case requires a minimum absorbed energy at a stated temperature, that requirement belongs on the drawing with the specimen orientation and test temperature, because the default certificate values may be reported in a different orientation and at ambient temperature only.
Hardenability and Practical Section Limits
Hardenability is what separates this grade from a plain carbon steel of similar carbon content. Chromium and molybdenum shift the continuous cooling transformation curve to longer times, so a given section can be through-hardened with a slower and gentler quench. In practice, oil quenching of 42CrMo bars is reliable to roughly 50 to 70 mm diameter depending on the position of the composition within the specification and on the agitation of the quench tank; larger sections harden to a shell, and the depth of that shell must be established experimentally.
Water or polymer quenching extends the hardenable diameter but introduces a real cracking risk in a steel of this carbon content, particularly at sharp section changes, keyways, oil holes and thread roots. Where a heavy section must be fully hardened, the practical answers are a polymer quench with controlled concentration, a design that avoids stress concentrators in the transition zone, or a different grade with higher hardenability. Simply instructing a heat treater to quench harder is not a specification; it is a transfer of risk.
Grain size control also influences hardenability and toughness. A coarse austenitic grain size raises hardenability slightly but reduces toughness and increases distortion, so a fine grain practice with aluminium or niobium treatment is normally specified for components that will be case hardened or repeatedly heat treated.
Tempering Response and Property Selection
One composition can serve many strength levels because tempering temperature is a continuous control variable. The table below gives typical ranges obtained on oil-quenched sections of moderate size; the mill's or heat treater's test coupon governs the actual values for a specific order, because composition position, section size and holding time all shift the curve.
| Tempering temperature (degrees C) | Typical tensile strength (MPa) | Typical hardness (HBW) | Typical use |
|---|---|---|---|
| 180 - 250 | 1450 - 1600 | 430 - 480 | Wear parts, springs, high surface pressure |
| 300 - 400 | 1250 - 1450 | 380 - 430 | Highly stressed shafts under moderate impact |
| 450 - 550 | 1050 - 1250 | 320 - 380 | Gears, connecting rods, drive shafts |
| 560 - 620 | 950 - 1080 | 280 - 320 | Standard quenched and tempered structural use |
| 630 - 680 | 820 - 950 | 240 - 280 | Maximum toughness, heavy forgings, shafts |
The 250 to 400 degrees C band is a trap. Tempering in this range, which is common when a high hardness is wanted, leaves the steel in a region where toughness can be lower than after tempering at a higher temperature, and where the temper embrittlement sensitivity of the molybdenum-bearing composition is least effective. For components subject to shock, tempering above 500 degrees C and accepting a lower hardness is usually the better engineering choice, with surface hardening used separately where wear resistance is the actual requirement.
Holding time matters as much as temperature. Tempering time is normally scaled to section size, and a rule of one hour per 25 mm of section thickness at temperature, with a minimum of one hour, is a common industrial starting point. Under-tempering leaves a hard, brittle core in a thick section even when the surface hardness reading is correct.
Heat Treatment Practice and Common Faults
Austenitising for this grade is normally carried out in the 840 to 880 degrees C range, followed by oil quenching, then tempering at the temperature selected from the table above. Soaking time is set by section size and by the need to dissolve the carbides that carry chromium and molybdenum into solution; a short soak at the low end of the austenitising range leaves undissolved alloy carbides, which lowers the achieved hardness and makes the hardenability curve inconsistent from heat to heat.
Distortion and cracking most often originate in three places. The first is an uneven quench, where one side of the component sees still oil and the other sees agitated oil, producing a distortion that cannot be corrected by tempering. The second is quenching a component with a sharp change of section, where the thin section transforms first and the thick section later, generating tensile stress at the junction. The third is tempering too late: a delay of hours between quench and temper allows hydrogen to concentrate and quench cracks to open, and the standard practice of charging the furnace before the quench is complete exists for this reason.
Decarburisation during austenitising is a quiet defect. A decarburised layer lowers surface hardness, reduces fatigue strength and shows up as a soft skin on a hardness traverse. Controlled atmosphere or protective coating, plus a machining allowance sufficient to remove the affected depth, is the normal defence, and the required allowance should be agreed rather than assumed.
Machining, Welding and Surface Treatment
In the quenched and tempered condition the grade machines well with carbide tooling at the lower hardness levels and requires reduced feeds and more rigid setups at the higher ones. In the annealed or normalised condition it machines more easily but galls more readily, so a normalised and tempered supply condition is often chosen where a large amount of machining precedes the final heat treatment.
Welding is possible but is not the grade's strength. The carbon equivalent of a 0.4 percent carbon steel is high enough that cold cracking is a genuine risk, so welding calls for preheat, low-hydrogen consumables, controlled heat input and, for restrained or thick joints, a post-weld heat treatment. A welding procedure qualified on a low-carbon structural steel does not transfer to this grade. Where a component requires both high strength and extensive welding, the design should be reviewed rather than the weld procedure stretched.
For wear resistance, nitriding is a common surface treatment because the chromium and molybdenum content supports a hard nitride case, and the treatment temperature stays below the tempering temperature of most quenched and tempered supply conditions, so the core properties are preserved. Induction hardening and chrome plating are also used, but both require the core hardness to be specified separately, since neither improves the substrate.
Product Forms, Tolerances and Inspection
The grade is supplied as hot rolled or forged bar, as forgings, as seamless tube, and as plate for mould bases and machine structures. Each form carries its own dimensional standard and its own testing conventions, and the purchase order should name the form standard rather than only the steel grade. Forged bar additionally calls for an ultrasonic inspection agreement where the component is highly stressed, since internal discontinuities that are acceptable in a rolled bar may be unacceptable in a large forging.
Inspection items that should be fixed before order: the supply condition (annealed, normalised and tempered, or quenched and tempered); the hardness and hardness traverse requirement with the measurement positions; the test specimen location relative to the section; the ultrasonic acceptance level and the standard it references; the surface quality requirement including permitted decarburisation depth; and the dimensional tolerances for straightness, out-of-round and length. A certificate of the cast analysis alone does not answer any of these questions.
Traceability deserves the same attention. Heat number, bar or forging number, and the heat treatment charge number should appear on the marking and on the certificate, so that a hardness problem can be traced either to a chemistry deviation or to a furnace charge. Without the charge number, a failed mechanical test cannot be resolved and the entire lot becomes suspect.
Selection Checklist and Common Misconceptions
Three misconceptions recur in specifications. The first is that a higher hardness always means a better part; in a grade tempered for toughness, an increase in hardness obtained by lowering the tempering temperature often reduces the fatigue life of the component under cyclic bending. The second is that the tabulated mechanical properties are guaranteed for any section; they are reference values at a reference size. The third is that the grade is interchangeable with a tool steel of similar hardness; the alloy design, the cleanliness requirement and the tempering resistance differ, and substitution usually shows up first as distortion during heat treatment.
A workable selection sequence is: define the required core strength and the section size; check whether the hardenability at the specified composition range covers that section with the available quench; choose the supply condition; set the tempering temperature range consistent with the required toughness; specify the inspection items; and only then consider surface treatments. Following that order avoids the most expensive error in this grade, which is discovering after machining that the core of a heavy section never hardened.
FAQ
Q: Is 42CrMo the same steel as 42CrMo4 and 4140?
They are close equivalents across GB/T 3077, EN 10083-3 and ASTM A29/A29M, but the manganese, chromium and phosphorus ranges differ, so hardenability and embrittlement resistance are not identical.
Q: What is the carbon content of 42CrMo?
The standard range is 0.38 to 0.45 percent, and this medium-carbon level is what allows the grade to reach high strength after quenching and tempering.
Q: Can 42CrMo be welded?
It can, with preheat, low-hydrogen consumables, controlled heat input and often post-weld heat treatment, but the carbon equivalent is high enough that cold cracking must be treated as a real risk.
Q: Why did a large bar fail to reach the specified core hardness?
Because hardenability is limited by section size. Beyond roughly 50 to 70 mm in oil, the centre cools too slowly for a fully martensitic structure, so a hardness traverse on the actual section is the only reliable check.
Q: Is 42CrMo a die steel?
No. It is an alloy structural steel for quenched and tempered components such as shafts, gears and connecting rods, and it should not be ordered against a tool steel description.
Q: Which tempering range should be avoided?
Tempering between roughly 250 and 400 degrees C is avoided where toughness matters, because that band can give lower toughness than tempering at a higher temperature for a modest gain in hardness.




