NM500 steel plate is a high-strength wear-resistant steel plate. NM500 steel plate has high wear resistance and is also a type of carbon structural steel. It is a low-carbon steel (C ≤0.25%) and contains about 12% chromium. Due to its good hardenability and certain strength and toughness, it is often used as a material for gears, racks, shafts and other parts.
NM500 steel plate grade indicates: N is the first pinyin letter of "resistant" in "wear-resistant". M is the first pinyin letter of "wear" in "wear-resistant". 500 is the Brinell hardness value HB value. (The hardness value of 500 is a broad sense, and the domestic NM500 hardness value is around 500.)

What are the properties of NM500 steel?
- Chemical Composition (%) of NM450 Wear Resistant Steel:
| C | Si | Mn | P | S | Cr | Ni | Mo | Ti | B | ALs |
| 0.38 | 0.70 | 1.7 | 0.020 | 0.010 | 1.2 | 1.0 | 0.65 | 0.05 | 0.005- 0.006 | 0.010 min |
- Mechanical Properties of NM450 Wear Resistant Steel:
| Property | Impact test | HBW | ||
| Yield Mpa Min | Tensile Mpa | Elongation | Min J |
Min 470 |
| Thickness mm | Thickness mm | Degree | ||
| <70mm | <=80mm | % | -20 | |
- Hardness: Typically, NM500 steel has a hardness range of 470-550 HBW (Brinell Hardness), indicating its exceptional resistance to abrasion and wear.
- Strength: NM500 steel offers high strength, enabling it to withstand impacts and abrasive forces in harsh operating conditions.
- Toughness: It exhibits good toughness in addition to its hardness, allowing it to resist cracking and deformation under impact.
- Weldability: While welding high-strength abrasion-resistant steels can be challenging, NM500 steel offers reasonable weldability with appropriate procedures and precautions.
- Formability: NM500 steel may have limitations in terms of formability due to its high hardness and strength, requiring specialized forming techniques.
- Corrosion Resistance: Depending on the specific composition and treatment, NM500 steel may offer some corrosion resistance properties, but it is primarily valued for its abrasion resistance.

Characteristics of NM500 Steel
NM500 steel features a uniform microstructure that enhances its mechanical properties, maintaining high impact resistance even at low temperatures.
The steel's composition includes elements that improve its weldability and formability, making it suitable for harsh environments.
For customers, NM500 steel provides extended service life of components due to its superior wear resistance, reducing maintenance costs and downtime.
Its high strength and durability allow for thinner, lighter parts without compromising performance, leading to material and cost savings.
However, the high hardness of NM500 steel makes it challenging to machine and requires specialized equipment and techniques. For applications needing easier machinability, 450HB steel is recommended, offering a balance of hardness and workability.
Key Applications by Industry
| Industry | Critical Components | Performance Value |
|---|---|---|
| Mining | Excavator buckets, loader cutting edges, crusher liners, chutes, hopper liners, truck bed liners | Extends wear part life (e.g., chutes from 3 months to 18 months); cuts maintenance costs by ~50% |
| Construction & Earthmoving | Bulldozer blades, drill bits, conveyor components, asphalt paver screeds | Withstands aggregate/rock impact; reduces downtime from blade/cutting edge wear |
| Cement & Aggregates | Ball mill separators, clinker silo discharge cones, cyclone liners, conveyor screws | Resists silica-rich material abrasion at high speeds (up to 30 m/s); extends service intervals |
| Power Generation | Coal mill liners, coal feeder chutes, ash handling pipes, separator vanes | Handles coal/ash abrasion; lowers outage risk from component failure |
| Dredging & Marine | Dredge pipes, pump casings, suction lines, wear plates | Resists sand/silt erosion; withstands saltwater corrosion for longer service life |
| Waste Management | Waste compactors, landfill equipment liners, recycling machine blades | Withstands abrasive/impact loads from mixed waste streams |
Why NM500 Beats Alternatives
vs. AR500: Higher toughness (Ni/Mo) and better weldability via controlled carbon; better for impact-abrasion mix vs. AR500's ballistic focus.
vs. Mn13: Harder matrix (500 HBW vs. work-hardened Mn13) for consistent wear resistance without needing strain hardening; ideal for low-impact high-abrasion zones.
vs. Ceramic Composites: Lower total cost, easier fabrication/repair, and better impact resistance; avoids brittle ceramic cracking under heavy loads.
ROI Case Study
A coal-fired power plant replaced mild steel coal chutes with 12 mm NM500 liners: chute life rose from 4 months to 24 months; annual maintenance costs fell by 58%; downtime for replacements dropped by 70%, boosting plant availability and output.
If you want to learn more about GNEE's products, you can send an email to info@gneesteels.com. We are more than happy to assist you.
| Other steel plate by GNEE | ||||
| Name | Material | Specification (mm) | Tons | Remark |
| Clad steel plate | P265GH+410,S355JR+410,A516Gr70+316, A537CL1+304L,Q235B+304L,Q345B+304, A516Gr70(NACE)+410,A537CL1+904L, A537CL1+316L,A516Gr70+304L,A537CL1+304 ,A516Gr70+410,A516Gr70+904L |
2-300mm(Based plate),1-50mm(Composited plate) | / | UT, AR, TMCP.Normalized, Quenched and Tempered,Z Direction Test, Charpy V-Notch impact TestThe Third Party Test , Coated or Shot Blasting and Painting. |
| Low Alloy | Q345A, Q345B, Q345C, Q345D, Q345E, Q390, Q420, Q460C, ST52-3, S355J2+N, SS400, SA302GrC, S275NL, 35CrMo | 6 - 350 | 5788.56 | Normalizing, tempered ,controlled rolling, hot rolling , Hot rolling,1st inspection, 2nd inspection, 3rd inspection |
| Pressure Vessel Plate | A204 Grade B,A515 Grade 70,A537 Class 1,SA387 Grade 11 Class 1,P265GH,S537 Class 2,P355Q,P275N,P355N,P690Q,Q345R, | 3 - 300 | 8650 | Normalizing, tempered ,controlled rolling, hot rolling , Hot rolling,1st inspection, 2nd inspection, 3rd inspection |
| High-Strength Plate | A514 Grade F, A572 Grade 50, A588 Grade A, S355JR, S690Q, SS400, S690QL, Q345B, Q345E | 8 - 120 | 3086.352 | Quenched and tempered |
| Wear-Resistant Plate | NM360, NM400, NM450, NM500 | 6 - 150 | 3866.297 | Quenched and tempered |
| Ship Plate | ABS AH32,ABS DH32,ABS EH32,ABS FH36,ASTM A131 A, ASTM A131 EH32,ASTM A131 AH36,CCS A,CCS AH32,LR AH32, DNV A36,BV AH32 |
8 - 200 | 2853.621 | Hot rolling, normalized ,hot rolling controlled rolling, quenched and tempered + toughness and brittleness |




