S355G3 in the EN 10225 System
S355G3 is a weldable fine-grain structural steel plate specified in EN 10225, the European standard for structural steels used in fixed offshore structures. The designation is read in three parts: S for structural, 355 for the minimum yield strength in MPa at the thinnest thickness range, and G3 for a toughness and quality group that fixes the Charpy testing condition. The number after G is not a strength indicator and does not mean a higher grade than G2; it identifies how the steel is impact tested and, indirectly, how clean and how consistent the steel must be.
EN 10225 was written because offshore structures impose requirements that general structural plate standards do not cover: guaranteed toughness at sub-zero metal temperatures, tight limits on carbon equivalent for welding in a yard without post-weld heat treatment, controlled inclusion content for through-thickness ductility at tubular and stiffener connections, and a documented traceability chain from heat to finished plate. Plate ordered as S355G3 therefore carries a heavier inspection and documentation burden than an S355J2 plate of the same nominal strength.
Practically, S355G3 sits between general structural steel and the higher-strength offshore grades. It is used for deck plating, bulkheads, stiffeners, access structures, equipment supports and secondary structure where 355 MPa yield is sufficient, while primary nodes and highly restrained thick connections often move to S420 or S460 offshore grades or to plate with enhanced through-thickness properties.
What the Steel Is Made Of: Chemistry and Intent
The steel is a fully killed, fine-grain, micro-alloyed carbon-manganese product. Aluminium or another grain-refining addition is present to keep the austenite grain size small through rolling and normalizing, and micro-alloying elements such as niobium, vanadium and titanium are used sparingly to develop strength without inflating carbon. The result is a lean chemistry with a low carbon equivalent, which is the property that makes yard welding without preheat or post-weld heat treatment feasible at moderate thickness.
| Parameter | Typical S355G3 requirement | Why it is controlled |
|---|---|---|
| Carbon | 0.16% max | Limits hardness in the heat-affected zone and holds carbon equivalent down |
| Silicon | 0.55% max | Deoxidation; excessive silicon damages toughness |
| Manganese | 1.60% max | Strength and toughness balance; raised manganese requires higher carbon equivalent allowance |
| Phosphorus | 0.020% max | Segregation and temper embrittlement control |
| Sulphur | 0.010% max | Inclusion shape control; essential where through-thickness strain occurs |
| Aluminium (total) | 0.020% min | Confirms fine-grain practice |
| Carbon equivalent | Typically 0.43 max, subject to thickness | Governs preheat, heat input and cold-cracking risk |
| Pcm | Typically 0.24 max for low-carbon variants | Alternative weldability index used for very low carbon steel |
These figures describe limits that offshore orders commonly place on the grade rather than a single universal table, because EN 10225 allows the property package to be agreed between purchaser and mill within the framework of the standard. That is why a purchase order must state the analysis limits, the carbon equivalent limit and the delivery condition explicitly; two certificates both marked S355G3 can legitimately differ in micro-alloying and in carbon equivalent.
Strength and Ductility by Thickness
Yield strength falls as plate thickness rises, because thicker sections receive less rolling reduction and cool more slowly. S355G3 follows the conventional offshore pattern: 355 MPa minimum up to 16 mm, 345 MPa from 16 to 25 mm, 335 MPa from 25 to 40 mm, 325 MPa from 40 to 63 mm and 315 MPa from 63 to 100 mm. Tensile strength sits in the 470-630 MPa band across the range, with elongation of at least 22% in a 50 mm gauge length.
The tensile upper limit is as important as the minimum. Offshore design and welding procedures assume a defined strength window, and a plate that over-matches at 650 MPa can invalidate an undermatching consumable strategy and change the fracture assessment. Buyers should therefore check the upper tensile value on the certificate, not only the yield margin, and should confirm that the test frequency matches the project specification rather than the mill's default sampling plan.
Toughness and the Meaning of the G3 Suffix
The digit after G defines the Charpy verification condition applied to the grade: the test temperature and the minimum absorbed energy required, together with the specimen orientation and the permitted drop below the average. In offshore purchasing the suffix is the single most misread part of the designation, because G2 and G3 plate have the same strength but very different toughness evidence attached to them.
Because the suffix carries the testing condition, the purchase order should always spell out the required test temperature in degrees Celsius, the minimum average energy in joules, the minimum single value, the specimen size (10 x 10 mm where thickness allows, subsize with a defined scaling rule where it does not) and the direction of testing relative to the rolling direction. Asking only for "S355G3 with impact test" leaves the mill free to apply its own interpretation, and the resulting certificate may not satisfy the design premise.
Two secondary toughness controls matter for offshore fabrication. The first is testing after strain ageing, which is often requested where the plate will be cold formed; the second is the heat-affected zone and weld metal toughness of the qualified welding procedure, which is a separate qualification obligation and cannot be inferred from base metal results.
Delivery Condition and Its Effect on Properties
S355G3 plate is supplied in a controlled delivery condition, most often normalized (N) or thermomechanically rolled (M), with the condition identified on the certificate. Normalized plate has a uniform ferrite-pearlite structure that tolerates later hot forming and stress relief; thermomechanically rolled plate achieves its properties through controlled rolling and accelerated cooling and offers better toughness at a given carbon equivalent and lower cost, but loses strength if it is subsequently heated above the tempering range.
The fabricator must therefore match the delivery condition to the process route. A part that will be hot formed or subjected to post-weld heat treatment should be ordered normalized, or the thermal cycle should be simulated on the qualification coupon. A part that is cut, drilled and welded without elevated-temperature processing gains nothing from normalizing and can use the thermomechanically rolled route.
Welding S355G3 Offshore Plate
The grade is designed for welding and is normally welded with matching or slightly undermatching consumables under a qualified procedure. Preheat decisions follow the carbon equivalent, the thickness and the hydrogen level of the consumable rather than a fixed rule: at low carbon equivalent and moderate thickness, ambient-temperature welding with hydrogen-controlled consumables is common, while thick or highly restrained joints require defined preheat and a maximum interpass temperature to keep heat-affected zone hardness within the accepted ceiling.
Heat input should be bounded on both sides. Excessive heat input coarsens the coarse-grained zone and reduces its toughness; insufficient heat input raises hardness and cracking susceptibility. Offshore procedure qualification typically records a heat-input window and a hardness survey across the heat-affected zone, and the production welds must stay inside that window.
Repair welding deserves its own procedure. Excavation depth, preheat for the repair, number of repair cycles permitted at the same location and the inspection extent after repair should all be defined before fabrication begins, because uncontrolled repeated repair is one of the most common causes of local toughness loss in offshore steel structures.
Tolerances, Surface Quality and Through-Thickness Properties
Dimensional tolerances for S355G3 plate are taken from EN 10029 for thickness, width, length, flatness and edge condition unless the order specifies tighter limits. Offshore fabricators often require tighter flatness and reduced thickness minus tolerance because plate is assembled with automated welding and gap variation drives fit-up cost.
Surface quality is assessed against EN 10163, which classifies permissible discontinuities and repair by grinding. Where the plate will carry load in the through-thickness direction at welded T-joints, the order should invoke Z-quality grading under EN 10164 (Z15, Z25 or Z35) and, for critical connections, an ultrasonic examination of the plate body. Z-quality is not a strength property; it is a statement about the reduction of area in the short transverse direction, and it is achieved mainly through sulphur control and inclusion shape treatment.
Applications and Grade Selection
S355G3 plate appears in deck and accommodation structures, internal bulkheads, stiffened panels, walkways, crane and equipment foundations, boat landing support frames and secondary structural members of fixed platforms and offshore wind substations. In these locations the design is stiffness driven rather than strength driven, so 355 MPa yield with reliable toughness and good weldability is a better economic choice than a 420 or 460 MPa grade.
The grade should not be pushed into primary joint connections, thick node cans or highly restrained intersections where through-thickness strain and triaxial stress dominate, unless the order adds Z-quality and the welding procedure has been qualified for that restraint level. Where design metal temperature falls below the tested Charpy temperature of the offered plate, the correct response is a tougher grade or a lower test temperature, never a reinterpretation of the existing certificate.
Ordering and Receiving Inspection Checklist
State the standard and grade, the delivery condition (N or M), thickness, width and length, the tolerance standard, the analysis limits including carbon equivalent, the yield and tensile requirements with the thickness bands, the Charpy temperature and energy with orientation and specimen size, any Z-quality grade, the ultrasonic examination requirement, the surface acceptance class, marking, and the documentation set including inspection certificates with heat numbers traceable to each plate.
At receiving, verify plate identity against certificates, measure thickness at several positions, check flatness and edge condition, confirm the delivery condition marking, and cross-check the certified impact results against the ordered temperature and energy. Keep heat numbers traceable through cutting so that welding procedure records, non-destructive testing reports and any repair history can be linked to the exact plate used in each connection.
FAQ
Q: What does the G3 in S355G3 mean?
The G and following digit identify the toughness and quality group within EN 10225, which fixes the Charpy testing temperature and minimum absorbed energy. It is a test-condition indicator, not a strength ranking, so G3 is not stronger than G2.
Q: What is the chemical composition of S355G3 plate?
It is a fully killed, fine-grain carbon-manganese steel with carbon typically capped at 0.16%, manganese up to about 1.60%, silicon up to 0.55%, phosphorus and sulphur held at low residual levels and a minimum aluminium content for grain refinement.
Q: What yield strength does S355G3 offer in thick sections?
Minimum yield is 355 MPa up to 16 mm and falls in steps to about 315 MPa at 63-100 mm, with tensile strength in the 470-630 MPa band and a minimum elongation of 22% in 50 mm.
Q: Is S355G3 the same as S355J2?
No. S355J2 belongs to the general structural steel system of EN 10025-2, while S355G3 belongs to the offshore standard EN 10225 with tighter chemistry, controlled carbon equivalent and a defined Charpy condition; the two cannot be substituted on the basis of equal yield strength.
Q: Can S355G3 be welded without preheat?
At low carbon equivalent and moderate thickness, welding with hydrogen-controlled consumables at ambient temperature is normal practice. Thick sections and highly restrained joints call for defined preheat and a maximum interpass temperature, both stated in the qualified procedure.
Q: When is Z-quality required for S355G3?
Z-quality under EN 10164 is specified where welded joints load the plate through its thickness, as at T-joints and stiffener connections in restrained assemblies. It is achieved through sulphur control and inclusion shape treatment and is verified by through-thickness tensile testing.




