What SA656 Grade 60 Is
ASTM A656/A656M is the specification for hot-rolled structural steel plate of high-strength low-alloy quality with improved formability. The grade number states the minimum yield strength in ksi: Grade 60 therefore means a minimum yield strength of 60 ksi, which is approximately 415 MPa. The specification covers several types, which differ in alloying route and in whether atmospheric corrosion resistance is offered, and four strength grades in the common range. Because the specification is written for formability, the plate is intended to be bent, punched and welded in the condition in which it is delivered, without a separate heat treatment step at the fabricator.
The American Society of Mechanical Engineers adopts the same material as SA656 in its pressure and structural construction codes, so SA656 Grade 60 and A656 Grade 60 describe the same plate and appear interchangeably on drawings and mill certificates.
Mechanical and Chemical Basis
| Parameter | Requirement | Reference |
|---|---|---|
| Minimum yield strength | 60 ksi, approximately 415 MPa | ASTM A656/A656M |
| Minimum tensile strength | 70 ksi, approximately 485 MPa | ASTM A656/A656M |
| Delivery condition | Hot rolled, controlled rolling with micro-alloying | ASTM A656/A656M |
| Micro-alloying elements | Niobium, vanadium, titanium or combinations | ASTM A656/A656M |
| Types | Several types differing in composition and corrosion resistance | ASTM A656/A656M |
Strength is developed by a combination of grain refinement and precipitation hardening from micro-alloying additions, supported by controlled rolling practice rather than by alloy content alone. That approach keeps carbon low, so the plate retains ductility and can be formed and welded with the processes already used in a truck or equipment plant. Actual mill values typically sit above the specified minimums, and the tensile test results reported on the mill certificate are the values to use for design confirmation.
Main Applications
The primary use of Grade 60 is in structures where every kilogram matters but the fabrication shop works with conventional equipment. The main application groups are set out below.
| Application group | Typical components |
|---|---|
| Transportation equipment | Truck frames and chassis rails, trailer frames, tipper bodies, rail wagon components |
| Mobile and lifting equipment | Crane booms and outrigger components, aerial platform arms, forklift masts and carriages |
| Construction and civil works | Bridge girders and beams, building frames, temporary works, forming and shoring |
| Industrial and agricultural machinery | Machine frames, support structures, tool bars, implements and linkage parts |
| General welded fabrication | Brackets, gussets, reinforcement plates and formed parts that need a higher yield than Grade 50 |
The common thread is a component that is loaded in bending or fatigue and that benefits from either a thinner section or a higher payload at the same section. Grade 60 is often selected specifically as an upgrade from Grade 50 material in an existing design, because the strength increase comes with similar fabrication behaviour.
Forming, Welding and Machining
The plate is cold formed with bend radii taken from the supplier forming table for the grade and thickness. Because the yield strength is higher than mild steel, springback increases and the punch force grows; tooling and press capacity are reviewed before a forming operation is released. Sheared edges are dressed before tight bending where the edge is in tension, and hole punching is preferred over drilling for production runs provided the diameter and thickness limits are respected.
Welding uses consumables matched to the tensile range, with low-hydrogen practice for restrained or thick joints and preheat based on carbon equivalent and thickness. The micro-alloyed structure is not harmed by normal welding cycles, but excessive heat input and high preheat should still be avoided so that the heat-affected zone hardness and toughness remain acceptable. The material is machined with conventional tooling at speeds suited to a quenched-free low-alloy steel; it is normally supplied without a requirement for post-weld heat treatment.
Ordering and Inspection Points
When Grade 60 plate is purchased, the order should state the specification and grade, the type where corrosion resistance or a particular alloying route is required, the thickness and tolerances, the delivery condition and the inspection document. Mill certificates are issued against the heat and the test results; additional ultrasonic testing is specified when the plate is used in a dynamically loaded or safety related component. Thickness tolerance is a commercial as well as a technical point, since the strength advantage of the grade is frequently realised by reducing the section.
Frequently Asked Questions
Q: What is SA656 Grade 60 used for?
A: It is used for weight-sensitive fabricated structures such as truck frames and chassis, trailer and rail components, crane booms, platform arms, bridge girders, machine frames and general welded parts requiring a higher yield than Grade 50.
Q: What is the yield strength of SA656 Grade 60?
A: The minimum yield strength is 60 ksi, approximately 415 MPa, with a minimum tensile strength of 70 ksi, approximately 485 MPa, under ASTM A656/A656M.
Q: Is SA656 the same as A656?
A: Yes. SA656 is the designation used by ASME for the same plate specification, and the two designations appear interchangeably on drawings and certificates.
Q: Can SA656 Grade 60 be welded?
A: Yes. It is welded with consumables matched to the tensile range and low-hydrogen practice for thick or restrained joints; preheat is selected from the carbon equivalent and thickness of the heat.
Q: Does SA656 Grade 60 need heat treatment after forming?
A: No. The grade is delivered in the hot-rolled, micro-alloyed condition and is intended for cold forming and welding without a subsequent heat treatment.
Q: What is the difference between the types of A656 plate?
A: The types differ mainly in alloying route and in whether the plate offers enhanced atmospheric corrosion resistance; the strength grade and the minimum yield strength are separate from the type.




