What is the yield strength of ASME SA537 Class 1 ?
The minimum yield strength of ASME SA537 Class 1 pressure vessel steel plate is 50 ksi ( 345 MPa ) for thicknesses up to 65 mm ( 2.5 inches ). For thicker plates ( to 100 mm ), the minimum yield strength is reduced to 45 ksi ( 310 MPa ).

ASME SA537 Class 1 is a heat-treated carbon-manganese-silicon steel plate specifically developed to meet the safety requirements of the ASME Boiler and Pressure Vessel Code. It is distinguished by its ability to provide a high yield point of 50 ksi alongside excellent ductility. The material is produced through a process that involves heating the plate until its crystal structure transforms and then allowing it to cool naturally, ensuring the finished vessel shell is resistant to the brittle failures that can occur in non-heat-treated steels under cold or pressurized conditions.
Key Characteristics
Uniformity of Properties: Eliminates internal stresses from the rolling process through heat treatment.
Broad Temperature Range: Effective for service from moderate low temperatures up to several hundred degrees.
Ductile Failure Mode: High elongation values ensure the material deforms before it fails.
Economic Strength: Provides high load capacity at a lower cost than stainless or high-alloy steels.
Grade Designation
"SA": ASME Section II identifier for Ferrous Materials.
"537": The specific material specification for "Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel."
"Class 1": Indicates the material has been Normalized.
UNS Number: K02400.
Comparison (vs. SA515 Grade 70)
Toughness: SA537 Cl. 1 is for low-to-moderate temp; SA515 is for high-temp, coarse-grain service.
Impact Testing: SA537 is generally impact-tested; SA515 has poor low-temperature toughness.
Hardenability: SA537's Manganese/Silicon content is higher to facilitate the normalization effect.
Grain Size: SA537 is fine-grained; SA515 is coarse-grained.

Common Applications
Pressure Piping Reinforcements: For high-stress manifold sections.
LPG Sea Transport Tanks: Built into the hulls of specialized gas carrier ships.
Refinery Distillation Columns: Lower sections of towers where weight and strength are critical.
Blast Furnaces: Outer shells where pressure and structural integrity must be maintained.
What is the hardness of ASME SA537 Class 1?
The hardness of ASME SA537 Class 1 is typically around 200 HB (Brinell hardness). This hardness ensures that the material is durable and resistant to wear while maintaining the necessary ductility and toughness to withstand high-pressure and low-temperature environments. The hardness level strikes a balance between strength and toughness, ensuring the material can resist mechanical stresses without becoming brittle.
What is the tensile strength of ASME SA537 Class 1?
The tensile strength of ASME SA537 Class 1 typically ranges from 70 ksi (485 MPa) to 90 ksi (620 MPa). This high tensile strength allows the material to withstand significant mechanical stresses, making it ideal for use in high-pressure systems. The material retains its strength even under extreme temperature conditions, which is vital for applications like pressure vessels and reactors that operate in challenging environments.
What is the heat treatment required for ASME SA537 Class 1?
ASME SA537 Class 1 steel undergoes a heat treatment process that includes quenching and tempering. The steel is heated to a high temperature, rapidly cooled (quenched), and then tempered at a lower temperature. This process enhances the material's toughness, strength, and resistance to brittle fracture, making it suitable for use in demanding pressure vessel applications, where the material must maintain its integrity under high pressure and temperature conditions.
Chemical Composition of ASME SA537 Class 1
| C | 0.24 |
| Si | 0.15/0.50 |
| Mn < 40mm |
0.70/1.35 |
| Mn > 40mm |
1.00/1.60 |
| P | 0.035 |
| S | 0.035 |
| Cr | 0.25 |
| Mo | 0.80 |
| Ni | 0.25 |
| Cu | 0.35 |
Mechanical Properties of ASME SA537 Class 1
| Yield (MPa) | Tensile (MPa) | Elongation A50mm | Elongation A200mm | Thickness |
|---|---|---|---|---|
| 345 | 485-620 | 22% | 18% | < 65 |
| 310 | 450/585 | 22% | 18% | > 65 < 100 |
1. What is the impact toughness of ASME SA537 Class 1?
ASME SA537 Class 1 is tested for impact toughness at low temperatures, typically at -50°F (-46°C). The material must absorb at least 20 ft-lbs (27 J) of energy without fracturing. This high impact toughness ensures that the steel can perform safely under sudden, high-impact stresses, such as those that might occur in pressure vessels exposed to temperature fluctuations or thermal shocks.
2. What is the carbon content in ASME SA537 Class 1?
The carbon content in ASME SA537 Class 1 typically ranges from 0.12% to 0.20%. This low carbon content helps improve the material's weldability, reducing the risk of cracking during welding processes. Despite the low carbon content, the steel still retains sufficient strength and toughness, making it suitable for applications in high-pressure and low-temperature environments like pressure vessels and heat exchangers.
3. What is the weldability of ASME SA537 Class 1?
Yes, ASME SA537 Class 1 has good weldability, although care must be taken during the welding process. Preheating before welding and post-weld heat treatment (PWHT) are recommended to avoid cracking and minimize residual stresses. The relatively low carbon content improves its weldability, making it suitable for fabricating pressure vessels and other components that require welding in critical applications.
4. What industries rely on ASME SA537 Class 1?
ASME SA537 Class 1 is commonly used in industries such as oil and gas, chemical processing, petrochemical, and power generation. It is particularly important for manufacturing pressure vessels, reactors, and heat exchangers that need to perform under extreme pressures and temperatures. Its high toughness, resistance to brittle fracture, and good weldability make it ideal for industries that require durable and reliable materials in critical applications.
5. What is the elongation of ASME SA537 Class 1?
The elongation of ASME SA537 Class 1 is typically at least 18% in 8 inches (200 mm). This property indicates the material's ability to undergo plastic deformation without breaking. High elongation is crucial for pressure vessels and other critical components, where the material may experience sudden or extreme stress, ensuring the steel can absorb energy without failing or cracking.
6. What is the phosphorus content in ASME SA537 Class 1?
The phosphorus content in ASME SA537 Class 1 is limited to a maximum of 0.035%. Phosphorus can cause brittleness, especially in low-temperature environments, and affect the steel's toughness. By controlling phosphorus levels, ASME SA537 Class 1 ensures the material retains its strength and resistance to brittle fracture, making it suitable for high-stress, low-temperature applications such as pressure vessels and reactors.
7. What is the yield strength of ASME SA537 Class 1?
The yield strength of ASME SA537 Class 1 is typically around 50 ksi (345 MPa). This is the point at which the steel starts to deform plastically under stress. This yield strength ensures that the material can bear substantial loads without permanent deformation, making it suitable for critical applications in pressure vessels, where structural integrity must be maintained under high pressure and mechanical stresses.
Request a professional quotation for ASME SA537 Class 1from GNEE Steel.





