Mar 22, 2024 Leave a message

10CrMo910 Steel: 2.25Cr-1Mo Composition and High-Temperature Use

What the 10CrMo910 Designation Actually Covers

10CrMo910 is a German-origin designation for a 2.25% Cr-1% Mo low-alloy steel that belongs to the DIN 17175 family of seamless tubes for elevated-temperature service. The code is frequently misread. The leading "10" indicates a nominal carbon content of roughly 0.10%, "CrMo" names the two principal alloying elements, and "910" is an alloy sequence number, not a strength or temperature rating. In the current European framework the identical steel is standardised as 10CrMo9-10, material number 1.7380: EN 10216-2 covers the seamless pressure tube form and EN 10028-2 covers the pressure vessel plate form. In the American system the nearest equivalents are ASTM A335 Grade P22 for pipe and ASTM A387 Grade 22 for plate.

That overlap is the first commercial trap. A purchase order that says only "10CrMo910" leaves the supplier free to choose product form, delivery condition and test regime. A buyer who needs a 60 mm boiler drum shell is ordering plate; a buyer who needs a superheater tube is ordering seamless tube; the two are not interchangeable even when the ladle analysis falls inside the same window. Every technically complete order therefore names four things together: the designation, the product standard, the delivery condition and the inspection level.

Chemical Composition and the 2.25Cr-1Mo Balance

The grade sits in the middle of the low-alloy heat-resistant family. Chromium at around 2.25% provides oxidation resistance and solid-solution strengthening at temperature; molybdenum at around 1% suppresses softening and raises creep rupture strength far more efficiently than chromium alone. The ratio matters more than either element in isolation: a heat that drifts to 1.9% Cr while holding 1.1% Mo will still pass a casual spectro check yet will sit at the bottom of the creep scatter band after 100,000 hours at 540 degrees C.

Because chromium and molybdenum are both ferrite stabilisers and both raise hardenability, the specification also caps residuals that damage toughness: phosphorus and sulphur are held low, and copper plus tin plus antimony plus arsenic are watched because they drive temper embrittlement in thick sections. Modern practice adds a J-factor or X-bar calculation to the purchase order for heavy plate intended for hydroprocessing service.

Element, % Seamless tube, DIN 17175 / EN 10216-2 (10CrMo9-10) Pipe, ASTM A335 Grade P22 Plate, ASTM A387 Grade 22
C 0.08-0.15 0.05-0.15 0.15 max
Si 0.15-0.50 0.50 max 0.50 max
Mn 0.40-0.70 0.30-0.60 0.30-0.60
P 0.025 max 0.025 max 0.025 max
S 0.020 max 0.025 max 0.025 max
Cr 2.00-2.50 1.90-2.60 2.00-2.50
Mo 0.90-1.10 0.87-1.13 0.90-1.10
Cu 0.30 max 0.40 max 0.40 max

Note the deliberate breadth of the A335 window. A pipe heat at 1.90% Cr and 0.87% Mo meets the letter of the standard but not the intent of a boiler designer who sized the tube wall on mid-range creep data. Where the design pressure is close to the allowable, restrict the order to the tighter EN window or add a supplementary composition requirement to the ASTM order.

Mechanical Properties and What the Numbers Do Not Tell You

Room-temperature tensile values are the least interesting property of this grade, yet they are the values most often quoted in supplier literature. The useful information is the combination of strength, ductility and the condition in which the properties were achieved, because 2.25Cr-1Mo plate and tube are normally supplied normalised and tempered, and any subsequent forming or welding that exceeds the tempering temperature will degrade the values obtained at the mill.

Product form and specification Tensile strength, MPa Minimum yield strength, MPa Minimum elongation, % Delivery condition
Seamless tube, EN 10216-2 (10CrMo9-10), wall up to 16 mm 450-600 280 20 Normalised and tempered
Pipe, ASTM A335 Grade P22 415 min 205 min 30 Normalised and tempered
Plate, ASTM A387 Grade 22 Class 2 515-690 310 18 Normalised and tempered
Comparison: 1.25Cr-0.5Mo plate, EN 10028-2 (13CrMo4-5) 440-590 290 19 Normalised and tempered

The comparison row explains a recurring procurement mistake. 10CrMo910 and 13CrMo44 are sometimes treated as interchangeable "chrome-moly boiler steels" because both are supplied normalised and tempered and both weld with matching low-hydrogen consumables. They are not interchangeable. 10CrMo910 carries roughly twice the chromium and twice the molybdenum, delivers a higher class-2 tensile window and holds creep strength to a service temperature some 30 to 40 degrees C higher. Substituting the leaner grade into a design calculated for 2.25Cr-1Mo silently removes a large part of the safety margin.

Elevated-Temperature Behaviour and Creep Life

The reason to pay for 2.25Cr-1Mo rather than carbon-manganese steel is long-term behaviour above about 400 degrees C. Carbon steel begins to lose creep resistance rapidly beyond 400 degrees C; 1.25Cr-0.5Mo extends useful service to roughly 540 to 560 degrees C; 10CrMo910 extends it again, with design data commonly tabulated up to about 580 degrees C and creep rupture data used beyond that for specific applications. Above roughly 600 degrees C the grade gives way to 9Cr-1Mo and to austenitic or advanced ferritic alloys, and insisting on 2.25Cr-1Mo at those temperatures is a design error, not a cost saving.

Two practical consequences follow. First, allowable stress is a function of metal temperature, not of the process fluid temperature; the designer must use the tube wall or plate mid-wall temperature at the hot end of the circuit, including any steam-side or fire-side credit. Second, creep damage is cumulative and irreversible. A unit that has run 80,000 hours at 560 degrees C has consumed most of its design life regardless of how the tensile test reads today, and a re-rating exercise should be based on remnant life assessment using replicas and hardness mapping rather than on a fresh mill certificate.

Oxidation resistance also limits the grade. In air or combustion gas the chromium level supports a protective oxide that stays intact to roughly 580 to 600 degrees C. In sulphur-bearing flue gas, in reducing atmospheres, or in the presence of alkali salts, that oxide breaks down at lower temperatures and the metal wastage rate becomes the controlling life mechanism rather than creep.

Plate, Tube and Forging Forms: Tolerances That Decide Fit-Up

Product form changes the dimensional rules, and fit-up problems in a boiler are almost always tolerance problems rather than metallurgical ones. Hot-rolled plate to EN 10028-2 is ordered to EN 10029 thickness tolerances, with normal, limited or restricted classes available; the restricted class is worth the small premium when the plate feeds a CNC plasma table, because a 0.8 mm thickness spread across a 2500 mm width changes the cut kerb compensation and produces inconsistent weld preparations.

Seamless tube to EN 10216-2 is ordered by outside diameter and wall thickness with defined tolerances, and the wall tolerance class must be stated. A tube ordered to the normal wall tolerance can be 12.5% under nominal at the thin point; a designer who sized the wall on nominal thickness has, in effect, designed to a thinner tube than the one delivered. For high heat flux sections, specify the tighter wall tolerance class and require wall thickness measurement at four quadrants on both ends.

Length, flatness, edge condition and surface quality follow the same logic: they are orderable options, not defaults. Plate ordered with sheared edges will not hold the squareness that a rolled shell course needs; plate ordered with mill edge and a specified flatness class will. State the option on the order and require it on the mill certificate.

Welding, Preheating and Post-Weld Heat Treatment

2.25Cr-1Mo steel is readily weldable but unforgiving of shortcuts. The hardenability introduced by chromium and molybdenum means that an unprotected arc strike or a rapidly cooled tack weld can produce a local hardness well above 350 HV, which is the classic precursor to hydrogen-assisted cold cracking in a thick-section boiler joint.

The standard sequence is: preheat the full joint, including a generous band either side of the groove, to roughly 200 to 250 degrees C for wall thickness above about 20 mm; maintain interpass temperature within the qualified range; weld with matching 2.25Cr-1Mo consumables such as AWS A5.5 E9015-B3 covered electrodes or AWS A5.28 ER90S-B3 filler wire, both fully baked and handled in heated quivers; and complete post-weld heat treatment without an intermediate cooling to ambient. Dissimilar joints to carbon steel or to 1.25Cr-0.5Mo components need their own procedure, because the tempering response of the two sides differs.

Post-weld heat treatment for this grade is normally carried out in the range of about 690 to 720 degrees C with controlled heating and cooling rates, holding time scaled to thickness, typically one hour per 25 mm of joint thickness with a minimum of one hour. Two rules are frequently broken. The first is the upper limit: exceeding roughly 740 degrees C converts part of the structure to fresh austenite that transforms to untempered martensite on cooling, and hardness testing will find it. The second is the number of cycles: repeated local heat treatments accumulate over-tempering and drop tensile strength below the specified minimum, so every heat treatment cycle must be recorded in the fabrication dossier and counted against the qualified maximum.

Temper Embrittlement and Hydrogen Service

Chromium-molybdenum steels in the 2.25Cr range are susceptible to temper embrittlement when held for long periods in the 350 to 550 degrees C band. Phosphorus, tin, antimony and arsenic segregate to prior austenite grain boundaries, raising the ductile-to-brittle transition temperature and reducing upper-shelf toughness. The effect is not visible in a room-temperature tensile test and is only exposed by Charpy testing after a step-cooling treatment or by testing material that has seen long service. For thick-wall vessels and for heavy forgings, specify a maximum J-factor and a maximum X-bar value, and require Charpy testing of the base metal, weld metal and heat-affected zone after simulated post-weld heat treatment.

In hydrogen service the grade is used for hydroprocessing reactors, heat exchangers and piping, where resistance to hydrogen attack depends on the chromium and molybdenum content and on the operating temperature and hydrogen partial pressure. The classic Nelson-type selection curves place 2.25Cr-1Mo in a band that covers most hydrotreating conditions up to roughly 450 degrees C. Above that envelope, or where the alloy has been welded and stress relieved, the alternative is the vanadium-modified 2.25Cr-1Mo-V grade with substantially higher strength and improved resistance. A buyer specifying hydrogen service should require a hardness survey, a documented post-weld heat treatment chart and impact testing of the weld heat-affected zone.

Inspection, Documentation and Ordering Data

A pressure part order is only as good as the inspection clause behind it. For 10CrMo910 in either product form the minimum acceptable package is: ladle and product analysis by the mill, tensile testing per heat or per specified frequency, impact testing where the design temperature or thickness triggers it, non-destructive examination at the level required by the applicable pressure vessel or boiler code, dimensional inspection against the ordered tolerance class, and a certificate that traces every item to its heat number and heat treatment charge.

Supplementary requirements worth adding for critical service include simulated post-weld heat treatment before mechanical testing, grain size reporting, hardness mapping across the thickness, ultrasonic examination of plate for laminations, and, for heavy sections, a documented step-cooling test. Each of these adds cost and lead time; each also removes a category of dispute that is almost impossible to resolve after the material has been cut and welded into a vessel.

Ordering data that should appear on the face of the purchase order: quantity and product form, designation plus product standard, delivery condition, dimensional tolerances and wall tolerance class, chemical restrictions tighter than the standard where relevant, mechanical test requirements including test temperature, non-destructive examination level, certificate type, marking and traceability requirements, and any restriction on repair welding. A supplier cannot be held to a requirement that was never written down, and a mill certificate is a statement about a heat, not a guarantee about the piece in your warehouse.

FAQ

Q: Is 10CrMo910 the same steel as 13CrMo44?
No. 10CrMo910 is a 2.25% Cr-1% Mo grade, standardised as 10CrMo9-10 in EN 10216-2 and EN 10028-2, whereas 13CrMo44 is a 1.25% Cr-0.5% Mo grade covered by EN 10028-2 as 13CrMo4-5. The chromium and molybdenum contents differ by roughly a factor of two, so the two are not interchangeable in a design calculated for elevated-temperature service.

Q: What is the maximum service temperature for 10CrMo910?
Design data are commonly tabulated to about 580 degrees C for long-term service, with oxidation resistance limiting continuous exposure in air to roughly the same level. Above about 600 degrees C the grade is normally replaced by 9Cr-1Mo or by austenitic alloys, and the allowable stress must always be read from the code table at the actual metal temperature.

Q: Why does a 10CrMo910 weld crack even though the procedure was followed?
The usual causes are loss of preheat on a thick joint, unbaked or damp low-hydrogen electrodes, a delayed post-weld heat treatment that allows hydrogen to concentrate, or a hardness peak at the heat-affected zone from excessive heat input followed by fast cooling. Check preheat measurement at the joint root, consumable handling records and the actual cooling curve before changing the welding procedure.

Q: Does a mill certificate guarantee that the plate meets the specification?
It certifies that the tested samples from the identified heat met the specified values. It does not certify the piece you received, because sampling position, heat treatment charge and subsequent processing all affect properties. Verification testing on the delivered item, plus dimensional and marking checks, is what closes the gap.

Q: What post-weld heat treatment temperature should be used?
For 2.25Cr-1Mo joints the usual window is about 690 to 720 degrees C, with holding time scaled to thickness and controlled heating and cooling rates. The upper limit is a real constraint: excursions above roughly 740 degrees C can re-austenitise part of the structure and leave untempered martensite after cooling.

Q: When is impact testing required on 10CrMo910?
Impact testing is triggered by the design code, by low design temperature, by thick section, and by any service where temper embrittlement or hydrogen is a concern. For heavy-wall and hydrogen service, Charpy testing after simulated post-weld heat treatment, covering base metal, weld metal and heat-affected zone, is standard practice rather than an optional extra.

Send Inquiry

whatsapp

phone

Email

Inquiry