Sep 26, 2023 Leave a message

Low Alloy Steel Plate: Q355B, Q345B, A572 Gr.50 and S355J2

What "Low Alloy Steel Plate" Means in Practice

Low alloy steel plate is a flat-rolled structural product in which the total deliberate alloying addition stays below the threshold that would move it into the alloy-steel category - conventionally under about 3.5% and in most commercial specifications between 1% and 2.5% of manganese, silicon, chromium, nickel, niobium, vanadium or titanium taken together. The base is still iron with 0.10-0.25% carbon, so the material remains weldable with ordinary carbon-steel procedures, machines with conventional tooling and is priced far closer to structural carbon steel than to stainless. What makes it useful is that a small, controlled alloy addition buys a disproportionate gain in yield strength, toughness or atmospheric durability.

The term is often used loosely, and that looseness costs buyers money. Three quite different families get called "low alloy plate": high-strength low-alloy structural grades such as Q355B, Q390C or ASTM A572 Gr.50; weathering steels to GB/T 4171 or ASTM A588/A588M that rely on copper, chromium and nickel to build a protective rust layer; and pressure-vessel or low-temperature grades such as Q345R to GB/T 713 or 16MnDR to GB/T 3531, where the alloying is tuned for notch toughness rather than strength alone. An order that names only "low alloy plate" can legitimately be filled with any of them, so grade, standard and delivery condition must be written explicitly.

The Reference Grade: Q355B and Its Predecessor Q345B

In metric practice the everyday answer to "what material is low alloy steel plate" is Q355B to GB/T 1591, the high-strength structural steel grade that replaced Q345B when GB/T 1591 was revised in 2018. The letter Q denotes yield strength, 355 is the minimum yield in MPa for the thinnest thickness range, and B is the quality class requiring 20 J minimum impact energy at +20 C on Charpy V-notch specimens. Older drawings, and a great deal of stock material still in circulation, refer to Q345B; the two are treated as near-equivalents in the market, but they are not the same specification. A drawing that states Q345B while the mill certificate shows Q355B should be checked against the design code rather than accepted on trust, because the yield floor moved by 10 MPa and the carbon and niobium limits were tightened.

Typical GB/T 1591 Q355B limits are: carbon 0.24% max, silicon 0.55% max, manganese 1.60% max, phosphorus 0.035% max, sulphur 0.035% max, nitrogen 0.012% max, with micro-alloying additions of niobium, vanadium and titanium constrained so that Nb+V+Ti does not exceed 0.22%, and residual chromium, nickel and copper each capped near 0.30%, 0.50% and 0.40% unless the grade letter indicates otherwise. Those ceilings are why the grade welds predictably: carbon equivalent, calculated as CEV = C + Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15, typically falls between 0.38 and 0.43 for a 20-40 mm plate - comfortably weldable without preheat at modest thickness, and needing 100-150 C preheat once sections exceed roughly 40 mm or the ambient temperature drops below 5 C.

Property (GB/T 1591 Q355B) Requirement Notes for buyers
Yield strength ReH 355 MPa min, t <= 16 mm Steps down with thickness; see next section
Tensile strength Rm 470-630 MPa Upper limit prevents over-strength embrittlement
Elongation A 22% min (short gauge, thin plate) Falls to about 20% in heavy plate
Impact, class B 20 J min at +20 C Class C is 0 C, class D is -20 C, class E is -40 C
Carbon equivalent CEV typically 0.38-0.43 Drives preheat and heat input decisions
Delivery condition As-rolled, normalised, or TMCP Must be stated; TMCP grades carry suffix M

Equivalent Grades Across Standards

Cross-standard substitution is the single most common source of dispute in low alloy plate purchasing, so the equivalences below should be treated as starting points for negotiation rather than as a licence to swap material. ASTM A572/A572M Grade 50 is the closest American analogue, with 345 MPa minimum yield and 450 MPa minimum tensile; the specification splits into Types 1 to 5 according to whether strengthening comes from manganese alone, niobium, vanadium, a niobium-vanadium combination or a titanium-niobium combination, and the type letter matters when welding procedures are qualified. EN 10025-2 S355JR and S355J2 correspond in strength but differ in impact testing: S355JR requires 27 J at +20 C, S355J2 requires 27 J at -20 C, and S355K2 requires 40 J at -20 C. Where sub-zero toughness is needed, EN 10025-3 S355NL delivers 27 J at -50 C in the normalised condition.

JIS G 3106 SM490A/B offers 325 MPa minimum yield for plate up to 16 mm with 490-610 MPa tensile, slightly lower strength than Q355 but widely accepted in marine and machinery work. For bridge structures the governing specification is GB/T 714 with grades such as Q345qD and Q370qE, which add tighter sulphur control, mandatory low-temperature impact and, for thick plate, a through-thickness or ultrasonic requirement. For pressure equipment the correct reference is GB/T 713, where Q245R and Q345R replace the structural grades entirely and bring mandatory elevated-temperature yield data, defined heat-treatment condition and restricted carbon equivalent for weldability.

System Grade Min yield Min tensile Impact requirement
GB/T 1591 Q355B 355 MPa (t <= 16) 470-630 MPa 20 J at +20 C
GB/T 1591 Q355D 355 MPa (t <= 16) 470-630 MPa 20 J at -20 C
ASTM A572/A572M Gr.50 345 MPa 450 MPa min Not mandatory at ambient
EN 10025-2 S355J2 355 MPa (t <= 16) 470-630 MPa 27 J at -20 C
EN 10025-3 S355NL 355 MPa (t <= 16) 470-630 MPa 27 J at -50 C
JIS G 3106 SM490B 325 MPa (t <= 16) 490-610 MPa Per grade and thickness

Strength Falls as Thickness Rises

Low alloy plate is not a constant-strength material, and the thickness-dependent de-rating in the standard is where design errors creep in. Because heavy plate cools more slowly after rolling, it develops a coarser ferrite-pearlite structure with less grain refinement, and the specified minimum yield drops accordingly. For Q355 the staircase runs approximately as follows: 355 MPa up to 16 mm, 345 MPa from 16 to 40 mm, 335 MPa from 40 to 63 mm, 325 MPa from 63 to 80 mm, 315 MPa from 80 to 100 mm, 295 MPa from 100 to 150 mm, 285 MPa from 150 to 200 mm and 275 MPa from 200 to 250 mm. The permitted tensile range is also relaxed in the heavy ranges.

Two practical consequences follow. First, a fabricator who qualifies a welding procedure on 10 mm plate and applies it to a 60 mm nozzle does so without the strength evidence the standard requires. Second, heavy plate is normally supplied in the normalised or thermomechanically rolled condition rather than as-rolled, because normalising refines the grain and restores toughness; the delivery condition code (N for normalised, M for TMCP) is part of the grade designation and must appear on both order and certificate. Thermo-mechanically controlled rolling grades such as Q355ME or Q355MC achieve the same strength at lower carbon equivalent, which improves weldability but restricts any subsequent normalising, since re-austenitising destroys the TMCP microstructure.

Three Misconceptions Worth Correcting Before Ordering

The first is that low alloy plate is corrosion resistant. It is not. A low alloy structural plate in the Q355 family will rust at essentially the same rate as Q235B carbon steel in the same environment, and the claim that such plate can be stored in the open in any climate and still resist air and water vapour is not supportable. Atmospheric corrosion resistance requires the weathering family - GB/T 4171 grades such as Q355NH and Q235NHD, or ASTM A588/A588M Grades A to C - where copper, chromium and nickel additions promote a dense, adherent oxide layer that slows further attack in alternating wet-dry conditions. Even those grades corrode steadily in permanently wet, marine-splash or chloride-laden conditions, and their use in bridge and building work assumes free drainage and periodic inspection.

The second misconception is that "low alloy" means close to stainless. Stainless relies on at least 10.5% chromium to form a passive film; a low alloy plate contains at most a few tenths of a percent chromium and owes its performance entirely to microstructure and section design. Painting, galvanising or a protective coating is mandatory wherever appearance or long-term section loss matters, and the coating system should be selected on the basis of the corrosivity category of the site rather than on the steel grade.

The third is that higher strength always allows a thinner section. Deflection, buckling, fatigue and fire performance frequently govern before yield does. A 355 MPa plate substituted for a 235 MPa plate at the same thickness raises the reserve on paper but changes weldability - the higher carbon equivalent demands preheat that the original procedure never specified - and can reduce toughness in the heat-affected zone if heat input is not adjusted to match.

Welding, Cutting and Forming Practice

Welding of low alloy structural plate follows carbon-manganese practice with three adjustments. Preheat is set from carbon equivalent and thickness rather than from habit: below CEV 0.40 and 25 mm, 20 C minimum is usually adequate; CEV 0.40-0.45 or thickness 25-50 mm calls for 100 C; above 50 mm or CEV 0.45, 150 C is normal, with interpass temperature capped around 250 C to protect toughness. Consumables should match or slightly undermatch the parent strength - an E43 or ER70S-6 filler is correct for Q355, not an over-matched E50 electrode - because an over-matched, high-strength weld metal in a low-alloy HAZ concentrates strain and promotes cracking. Heat input should be controlled within the range qualified for the procedure; very low heat input hardens the HAZ, while excessive heat input coarsens it and lowers impact energy.

Thermal cutting leaves a hardened, sometimes micro-cracked edge. For plates above about 30 mm in grades with CEV over 0.40, the cut face should be either machined back by 2-3 mm or preheated before cutting, and edges should be inspected for hardness and for laminar defects before welding. Cold forming is straightforward up to moderate radii, but bending across the rolling direction requires a larger minimum bend radius than bending along it, and heavily cold-worked corners in thick plate may need normalising stress relief. Flame straightening should be limited to the temperatures permitted by the specification, since local heating above roughly 650 C can degrade the properties achieved by TMCP.

Tolerances, Delivery Condition and Goods-In Inspection

Dimensions for metric plate are governed by EN 10029 thickness and shape tolerances, with GB/T 709 covering the domestic equivalent, while ASTM A6/A6M covers the inch-pound route; the permitted thickness minus tolerance in each is small but not zero, and a "20 mm" plate may lawfully arrive at 19.5 mm or thinner depending on the class ordered. Flatness, camber, edge condition - sheared, universal mill or gas-cut - and surface quality should all be written into the order. Common delivery conditions are as-rolled, normalised (N), normalised plus tempering, and TMCP (M); controlled rolling without a stated temperature regime is not a substitute for either.

Goods-in inspection should pair documentation with physical checks. From the EN 10204 3.1 certificate, verify grade and standard, heat number matching the stamp on the plate, product analysis against the standard table, carbon equivalent, tensile and yield results against the thickness band in force, Charpy impact energy at the specified test temperature, and the delivery condition code. On the plate itself, verify dimensions and thickness at several points, check for edge cracks and laminations, confirm marking transfer, and - where the grade is critical - run a portable hardness survey and, for thicker sections, ultrasonic examination to detect internal discontinuities. Keeping a retained sample from each heat is cheap insurance when a fabrication defect appears six months later.

Storage matters more than most buyers expect. Plate should be stacked clear of the ground on bearers, with faces separated so that water cannot stand between plates, and it should not be stored in contact with chloride-bearing dust or road salt. Intermittent wetting is far more damaging than continuous immersion for unprotected carbon and low alloy steel because the wet-dry cycle keeps supplying oxygen to the corrosion front.

FAQ

Q: Is Q345B still available, or has it been replaced?
Q345B belongs to GB/T 1591-2008; the current edition of GB/T 1591 uses Q355 as the 355 MPa grade. Q345B material is still traded and drawn on older drawings, but new designs should specify Q355B and the certificate should be checked against the edition quoted in the design documents.

Q: What is the alloy content limit for low alloy steel plate?
Conventionally under about 3.5% total deliberate alloying addition, and in most structural grades between 1% and 2.5%, dominated by manganese with small niobium, vanadium or titanium additions for grain refinement.

Q: Does low alloy plate resist corrosion without coating?
No. Q355-type plate corrodes at a rate similar to carbon steel. Only the weathering grades to GB/T 4171 or ASTM A588/A588M provide enhanced atmospheric resistance, and even they need free drainage and periodic inspection.

Q: Why does the specified yield strength drop for thick plate?
Slower cooling in heavy sections produces a coarser microstructure with less grain refinement, so GB/T 1591 and comparable standards reduce the minimum yield in steps as thickness increases, from 355 MPa at 16 mm to about 275 MPa at 250 mm.

Q: What preheat is needed for welding 30 mm Q355B?
With a carbon equivalent near 0.40-0.43, a preheat of about 100 C is typical for 25-50 mm sections, with interpass temperature held below roughly 250 C; the final figure should come from the qualified welding procedure for the actual joint.

Q: How do I tell Q355B from Q235B at goods-in?
Certification is primary - chemistry, carbon equivalent and tensile results differ clearly. Physically, a portable hardness or yield-based test gives an indication only, so grade substitution should be resolved through the 3.1 certificate and heat-number traceability rather than field testing alone.

Send Inquiry

whatsapp

phone

Email

Inquiry