What Q235 Hot Rolled Carbon Steel Plate Is
Q235 is a general purpose carbon structural steel defined by the Chinese standard GB/T 700. In the designation, Q stands for yield strength and 235 is the minimum yield strength in megapascals for the thinnest thickness range covered by the standard. The grade is supplied as hot rolled plate, sheet and coil, and it remains the default material for general fabrication, building structures, machinery and equipment where an alloyed or high strength grade is not needed.
Grades A to D and What Actually Changes
The four quality grades of Q235 differ in impact testing and in the phosphorus and sulfur limits, not in strength. Moving from A to D buys toughness at progressively lower service temperatures and cleaner steel, which shows up in the price almost as clearly as in the certificate.
| Grade | Charpy impact test | P max | S max | Selected for |
|---|---|---|---|---|
| Q235A | Not normally required | 0.045 % | 0.050 % | Indoor structures, general fabrication |
| Q235B | 27 J at 20 degrees C | 0.045 % | 0.045 % | The most widely ordered grade |
| Q235C | 27 J at 0 degrees C | 0.040 % | 0.040 % | Outdoor structures, cooler climates |
| Q235D | 27 J at minus 20 degrees C | 0.035 % | 0.035 % | Low temperature outdoor service |
Mechanical Properties and Thickness Effect
Yield strength falls as the section becomes heavier, because the cooling rate after rolling slows down and the grain structure coarsens. GB/T 700 sets the requirement by thickness range, and the tensile range is given rather than a single target value.
| Nominal thickness | Minimum yield strength | Tensile strength | Minimum elongation |
|---|---|---|---|
| 16 mm and under | 235 MPa | 370 - 500 MPa | 26 % |
| over 16 mm to 40 mm | 225 MPa | 370 - 500 MPa | 26 % |
| over 40 mm to 60 mm | 215 MPa | 375 - 500 MPa | 25 % |
| over 60 mm to 100 mm | 215 MPa | 375 - 500 MPa | 24 % |
| over 100 mm to 150 mm | 195 MPa | 375 - 500 MPa | 22 % |
Carbon is held to a maximum of about 0.20 % in grades B to D and silicon to about 0.35 %, with manganese up to about 1.40 %. That combination is what keeps the carbon equivalent low enough for routine welding.
Plate Sizes, Tolerances and Processing
Thickness: hot rolled plate is commonly supplied from about 3 mm up to 150 mm and beyond for heavy sections, while thickness below roughly 6 mm often crosses into coil and sheet territory.
Width and length: standard mill widths generally fall between 1200 mm and 4000 mm, and length is cut to order, so plate can be supplied to a fixed length or as coil for a cutting line.
Tolerance: thickness and shape tolerances follow the plate dimensional standard selected for the order, GB/T 709, in a specified tolerance class; a tighter class is worth agreeing in writing where the plate feeds a controlled fabrication line.
Processing: cutting to size, shearing, bending, decoiling, punching and welding are carried out either at the mill or at a service centre, and pickled and oiled plate is available where the mill scale has to be removed before painting or forming.
Surface: the plate can be supplied as hot rolled with mill scale, pickled, or galvanized for roofing, wall panels and outdoor cladding where the bare steel would not survive.
Weldability and Where Q235 Is Used
Q235B and Q235C weld easily with the E43 series covered electrodes classified in GB/T 5117, and with the corresponding gas shielded solid wires, without preheating at ordinary thickness. Preheat is only considered for heavy sections, for high restraint joints or for low ambient temperature working, and the welding procedure should always be qualified for the thickness and position involved.
Building and industrial structures, including frames, columns, platforms and stairways.
General machinery, equipment bases, racks and fabricated parts that need moderate strength and good formability.
Roof and wall panels, cladding and decorative sheet work, frequently in galvanized condition.
Storage tanks, hoppers, ducts and non-pressure vessels of ordinary duty.
Bridges and transport structures of small to medium span where a higher strength grade is not required by the calculation.
Compared with near-equivalent grades in other systems, Q235B is broadly used in the same applications as a 235 MPa low-alloy or non-alloy structural plate supplied under other designations, but the certification, the impact level and the residual element limits are set by GB/T 700 and should be read from the mill certificate for the actual plate. Where atmospheric corrosion resistance rather than strength is the design driver, a weathering structural grade such as Q355NH in GB/T 4171 is the appropriate material instead of a plain carbon plate.
Frequently Asked Questions
Q: What does Q235 mean in a steel plate designation?
Q indicates yield strength and 235 is the minimum yield strength in MPa for the thinnest thickness range, so Q235 plate is a 235 MPa general purpose carbon structural steel to GB/T 700.
Q: What is the difference between Q235A and Q235B?
Grade B has an impact energy requirement of 27 J at 20 degrees C and a tighter sulfur limit, while grade A has no routine impact test. Q235B is the safer default for welded structures.
Q: Is Q235 the same as Q345?
No. Q345 is a higher strength low-alloy structural grade with a minimum yield of 345 MPa in the thin range, so plate thickness can be reduced but the price per tonne is higher and the welding procedure changes.
Q: Can Q235 plate be welded without preheating?
Yes in ordinary thickness. With low carbon and a modest carbon equivalent, E43 series electrodes produce sound joints, and preheat is reserved for heavy, highly restrained or cold weather welding.
Q: What is the maximum tensile strength of Q235 plate?
The standard gives a range rather than a maximum, typically 370 to 500 MPa for the thinner ranges and 375 to 500 MPa for heavier plate, with yield strength falling as thickness increases.
Q: Is Q235 plate suitable for outdoor structures?
It is widely used outdoors, but as a plain carbon steel it relies on paint or galvanizing for durability. For exposed atmospheres without a coating, a weathering structural grade is the better choice.




