Nov 12, 2026 Leave a message

Z15 Z25 Z35 S690QL1 High Strength Steel Plate

S690QL1 is a quenched and tempered high-strength structural steel per EN 10025-6, delivering 690 MPa minimum yield strength and -60°C Charpy V-notch toughness. But when you add Z15, Z25, or Z35 through-thickness quality requirements per EN 10164, you get a plate engineered to handle the most demanding welded joint conditions.

 

 S690QL1 high-strength structural steel

What Is Through-Thickness (Z-Direction) Property in Steel Plate?

 

Z-Direction In Steel Plate

Rolled steel plate is not isotropic - its mechanical properties differ depending on the direction you test them. Standard tensile and impact tests are performed along the rolling direction (longitudinal) or across the plate (transverse). But there is a third direction that is often overlooked until problems occur: the through-thickness direction, also called the Z-direction or short-transverse direction.

 

During the rolling process, non-metallic inclusions - primarily manganese sulfide (MnS) stringers - become elongated and flattened into thin layers parallel to the plate surface. These elongated inclusions create planes of weakness that dramatically reduce ductility in the Z-direction. When weld shrinkage pulls perpendicular to the plate surface in a thick, highly restrained joint, this limited through-thickness ductility can cause a specific type of failure called lamellar tearing.

 

Lamellar tears are stepped internal cracks that form parallel to the plate surface, usually beneath weld beads in T-joints, cruciform joints, and corner joints. They are often invisible from the surface and may go undetected unless ultrasonic testing is performed - making them particularly dangerous in load-bearing structures.

Key point: Z-grade steel is not a separate steel grade. It is a through-thickness performance requirement applied to an underlying grade like S690QL1, designated by appending Z15, Z25, or Z35 (e.g., S690QL1-Z35). The governing standard is EN 10164.

Z15 vs Z25 vs Z35: Understanding the Three Quality Classes

 

EN 10164:2018 defines three quality classes for through-thickness properties, based on reduction of area (RA) measured in through-thickness tensile tests. The higher the class, the greater the through-thickness ductility and the more demanding the application it can handle.

Z Class Min. Average RA (3 tests) Min. Individual RA Typical Application Context
Z15 ≥ 15% ≥ 10% Moderately restrained thick plate joints, lighter structural applications
Z25 ≥ 25% ≥ 15% Highly restrained heavy plate connections; general structural welding with moderate restraint
Z35 ≥ 35% ≥ 25% Critical applications: offshore, heavy bridges, demanding structural nodes

 

How Z-Quality Is Tested: The Through-Thickness Tensile Method

Z-direction performance is verified by machining cylindrical test specimens perpendicular to the plate surface and pulling them to fracture at room temperature. The reduction of area at the fracture surface is calculated using the formula:

 

RA (%) = (A&subscript-0; − Ar) / A0 × 100

 

A minimum of three specimens must be tested, and both the average value and each individual test result must meet the class requirements. The test area is also ultrasonically examined before testing to ensure no pre-existing laminations that could skew results.

 

🔧 Not sure which Z-class your welded connections need?

Our technical team can review your joint design drawings and recommend the appropriate Z15, Z25, or Z35 requirement based on plate thickness, weld configuration, and restraint level.

Get Free Technical Consultation →

Why Z-Direction Property Is Critical for S690QL1 High-Strength Steel

 

Not every steel grade needs Z-grade options. But for S690QL1 and other high-strength quenched and tempered steels, through-thickness performance is especially important - here is why:

 

1. Thick-Section Usage Inherently Carries Higher Risk

S690QL1 plates are commonly specified in thicknesses up to 150 mm for heavy load-bearing structures. Thicker plates mean more material through the cross-section, larger weld deposits, and greater shrinkage forces acting in the Z-direction. The thicker the plate, the higher the lamellar tearing risk.

 

2. High-Restraint Joints Are the Norm, Not the Exception

The applications where S690QL1 is specified - offshore jacket nodes, crawler crane booms, mining dump truck bodies, heavy bridge girders - almost always involve heavily restrained T-joints, cruciform joints, and full-penetration welds. These joint types generate the highest through-thickness shrinkage strains and are exactly where lamellar tearing is most likely to occur.

 

3. High Strength Leaves Less Ductility Margin

Steel with 690 MPa yield strength operates closer to its elastic limit than conventional S355 steel. When through-thickness strains from welding are superimposed on service loads, there is simply less ductility reserve available before cracking initiates. Z-grade plating ensures that the through-thickness direction has sufficient ductility to absorb weld shrinkage without failure.

 

4. Combined Failure Risk: Lamellar Tearing Plus Cold Cracking

High-strength steels already require careful control of preheat temperature, heat input, and hydrogen levels to prevent cold cracking. When through-thickness restraint is also present, the two failure mechanisms can compound. Specifying Z-quality S690QL1 removes one major variable from the equation and gives fabricators greater margin for error.

 

Applications Where S690QL1 Z-Grade Plate Is Essential

 

Offshore & Marine Engineering

Offshore platform jacket nodes, transition pieces for offshore wind turbine foundations, jack-up rig leg components, and subsea structures all combine thick plate, full-penetration welding, and dynamic cyclic loading. Z-grade S690QL1 (typically Z25 or Z35) is standard practice in these applications to ensure joint integrity over decades of service.

Offshore & Marine Engineering

Heavy Machinery & Construction Equipment

Mobile crane outrigger boxes, crawler crane chassis frames, mining shovel dippers, dump truck bodies, and tunnel boring machine components rely on S690QL1 for its exceptional strength-to-weight ratio. Where thick-plate T-joints and cruciform joints carry high through-thickness stress, Z-grade specification prevents lamellar tearing during fabrication and service.

    Heavy Machinery & Construction Equipment

Bridges & Infrastructure

Long-span bridge main girders, heavy bridge node plates with full-penetration welds, stadium roof truss connections, and high-rise building mega-column joints all benefit from Z-quality assurance. Bridge codes in particular often mandate through-thickness testing for plates above a certain thickness.

   Bridges & Infrastructure

Pressure Vessels & Industrial Equipment

For thick-walled pressure vessel shells and heavy industrial skid structures, through-thickness ductility is critical. Note that while S690QL1 is a structural steel per EN 10025-6, the pressure vessel equivalent is P690QL1 per EN 10028-6 - both are available with Z-grade options.

Rule of thumb: Z-direction performance should be considered for plates ≥40 mm thick that carry through-thickness tensile stress from welding. For S690QL1 in critical applications, many engineers specify Z25 as standard and Z35 for the most demanding joints.

📋 Working on a project that requires Z-grade S690QL1 plate?

We stock S690QL1 plates with Z15, Z25, and Z35 through-thickness properties in thicknesses from 10 mm to 150 mm. Send us your material specification and required quantities for a competitive quotation.

Request a Free Quote Now →

How S690QL1 Z-Grade Steel Is Produced

 

Achieving reliable through-thickness ductility in high-strength steel requires careful control of steelmaking practices. The single most important factor is sulfur content and inclusion morphology control.

Steelmaking Practice Sulfur Content Inclusion Control Achievable Z-Class
Standard killed steel 0.015–0.025% MnS elongation (stringers) Not qualified
Calcium treated 0.005–0.010% Sulfides globularized as CaS Z15 – Z25
Vacuum degassed + Ca treated 0.003–0.008% Ultra-low S + shape control Z25 – Z35
Electroslag remelted (ESR) <0.003% Exceptionally clean Z35+

 

S690QL1 already has a maximum sulfur limit of 0.010% per EN 10025-6, which provides a good starting point for Z-quality. To reliably meet Z25 and Z35 requirements, mills use calcium treatment to globularize sulfide inclusions (replacing elongated MnS stringers with spherical CaS particles) and vacuum degassing to reduce overall sulfur and hydrogen levels.

 

Chemical Composition,Mechanical Property and Equivalent steel grade of S690QL1

 

S690QL1 Chemical Composition

Grade

The Element Max (%)

C

Si

Mn

P

S

N

B

Cr

S690 QL1

0.20

0.80

1.70

0.020-0.025

0.010-0.015

0.015

0.005

1.50

Cu

Mo

Nb

Ni

Ti

V

Zr

 

0.50

0.70

0.06

2.0

0.05

0.12

0.15

 

 

Grade

S690QL1 Mechanical Property

Thickness

Yield

Tensile

Elongation

Min Impact Energy

 

S690 QL1

mm

Min Mpa

Mpa

Min %

-60

30J

3

890

940-1100

11

-60

30J

50

830

880-1100

11

-60

30J

100

800

820-1000

11

-60

30J

 

Equivalent steel grade of S690QL1

Europe

Germany

France

Sweden

 

EStE 690 V

-

-

Ready to Specify the Right S690QL1 Z-Grade Plate?

Whether you need Z15, Z25, or Z35 through-thickness quality, our team can help you select the right material for your application and provide a competitive quotation. Send us your project specifications today.

📧 Send Your RFQ Now

 S690QL1 Z-Grade Plate shipping

FAQ

 

Does specifying Z-grade change the mechanical properties in the rolling direction?

No. Z-grade is a through-thickness ductility requirement only. The yield strength, tensile strength, elongation, and Charpy impact properties in the longitudinal and transverse directions remain identical to the base S690QL1 grade.

 

Is Z35 always better than Z25?

Not necessarily - it depends on your application. Z35 provides the highest through-thickness ductility but also carries a cost premium. Z25 is sufficient for most heavy structural applications. Z15 is appropriate for moderate restraint conditions. Specifying a higher Z-class than needed adds unnecessary cost.

 

What is the difference between S690Q and S690QL?

S690Q: Minimum impact toughness tested at -20°C (30J average). → Typical Use: Cranes in temperate climates, quarry equipment. S690QL: Certified for -40°C and below (≥40J impact toughness). → Critical Use: Arctic pipelines, offshore platforms, mining vehicles in Siberia.

 

What is the price of S690QL material?

S690QL High Strength Steel Plates, Thickness: 5mm to 150mm at $1.44 / kilogram.

 

What is the hardness of S690 QL steel?

S690QL steel stockholders and suppliers. S690QL is a quenched and tempered high strength steel supplied in full plates or cut pieces with delivery to the whole of the UK. With its high yield of minimum 690MPa it offers better strength than standard carbon steel grades.

 

What is the effective use of high strength S690 steel in construction?

The high strength S690 steels have an excellent strength-to-self-weight ratio, and they are highly efficient to be used in heavily loaded structures. Typical applications include piles and columns in buildings and supporting members in bridges.

Send Inquiry

whatsapp

phone

Email

Inquiry