Reading the 18CrMnNi2Mo Grade Symbol
18CrMnNi2Mo belongs to the nickel-molybdenum family of carburizing alloy steels, the group used for gears and shafts that must carry high bending load while keeping a soft, shock-absorbing core. The symbol is a composition shorthand rather than a trade name. The leading "18" is the nominal carbon content in hundredths of a percent, about 0.18% C, which is low by design because the wear surface gets its carbon later from the furnace atmosphere. "Cr", "Mn", "Ni" and "Mo" list the alloying elements in descending order of their nominal content, the "2" after Ni fixes nickel at roughly 2%, and the trailing "Mo" indicates a deliberate molybdenum addition, typically a few tenths of a percent.
That molybdenum addition is the technical heart of the grade. Molybdenum is the most effective single element for suppressing temper embrittlement in nickel-bearing steels: it scavenges phosphorus and tin at grain boundaries and keeps the steel from becoming brittle when it cools slowly through the 350-550 deg C range after tempering, or when it operates hot for years. Combined with 2% nickel, which supplies toughness and hardenability, and 1.2% chromium, which forms the carbides that make the case wear resistant, the result is a grade that behaves well in large sections where a lean manganese-chromium carburizing steel would come out with a soft core and a brittle transition.
Chemical Composition and Why Each Element Is There
Bars and forgings in this grade are ordered against the alloy structural steel standard GB/T 3077 for composition and mechanical properties, with dimensional and surface requirements taken from the applicable GB/T product standard for the form supplied. The ranges below are typical of commercial mill practice for the grade; the mill certificate for the actual heat is the document that governs acceptance, and every figure on a drawing should be traceable to it.
| Element | Typical range (wt.%) | Engineering purpose |
|---|---|---|
| C | 0.15 - 0.21 | Low carbon keeps the core ductile; case carbon is added later |
| Si | 0.17 - 0.37 | Deoxidation; excess silicon impairs carburizing response |
| Mn | 0.90 - 1.20 | Hardenability at low cost; also binds sulphur |
| Cr | 1.10 - 1.40 | Carbide former; raises case hardness and resistance to softening |
| Ni | 1.80 - 2.20 | Core toughness, deep hardening, grain refinement |
| Mo | 0.20 - 0.30 | Hardenability, resistance to temper embrittlement, carbide stability |
| P | 0.025 max | Controlled tightly - the element that drives embrittlement |
| S | 0.030 max | Controlled; higher sulphur only by agreement for free machining |
Two limits deserve commercial attention. The phosphorus cap is tighter than on general structural steel because molybdenum's protection against temper embrittlement is finite; once phosphorus exceeds roughly 0.025%, the molybdenum addition is partly consumed tying it up and the benefit to toughness falls away. And the silicon range is a processing constraint, not a strength requirement: silicon above about 0.35% slows carbon diffusion and reduces case depth for the same cycle time, so a heat that is chemically acceptable can still produce short cases in the heat treater's standard recipe.
What This Grade Is Not: Correcting the Corrosion-Resistance Claim
Pages describing 18CrMnNi2Mo sometimes present it as a corrosion-resistant material, able to resist acid, alkali and seawater, and recommend a solution treatment at 1050-1150 deg C. Both statements are wrong for this steel and both cause real damage when acted upon. With only about 1.2% chromium, the grade cannot form the continuous passive chromium-oxide film that gives stainless steel its corrosion resistance - that film needs roughly 10.5% chromium or more. A 1.2% Cr steel will rust in a humid workshop, let alone in seawater.
The 1050-1150 deg C "solution treatment" is copied from austenitic stainless practice. Applied to a low-carbon carburizing steel it does three harmful things: it coarsens the austenite grain, it scales the surface heavily, and it leaves the part with a coarse structure that cannot be corrected by a single subsequent normalizing pass without adding distortion. The correct pre-machining treatment is a normalize or an isothermal anneal in the 880-920 deg C range, and the correct hardening treatment is a carburize-quench-temper cycle, not a solution anneal.
Where genuine corrosion resistance is required - chemical plant piping, food-contact vessels, marine structures - the correct answer is a different material class, such as an austenitic stainless steel to ASTM A240 or a duplex grade, not a carburizing alloy steel. Understanding where a grade stops being suitable is as much a part of selection as knowing its strengths.
Hardenability, Core Strength and Case Performance
The grade's practical value appears in sections between roughly 30 mm and 150 mm, where the combination of 2% nickel and 0.25% molybdenum keeps the core hardenable in oil while the low carbon keeps it tough. A leaner carburizing steel in a 100 mm gear blank can end up with a ferrite-banded core that deforms under tooth bending; this grade hardens through by comparison, and its core hardness after tempering lands in the 30-40 HRC band, which is the range most gear designers target.
| Property | Condition | Typical value |
|---|---|---|
| Tensile strength, Rm | Quenched and tempered, 25 mm reference | 1000 - 1200 MPa |
| Yield strength, Rp0.2 | Quenched and tempered | 800 - 950 MPa |
| Elongation, A | Quenched and tempered | 10 - 13 % |
| Charpy V energy, KV2 | 20 deg C, longitudinal | 50 - 70 J |
| Core hardness | After carburize, quench, temper | 30 - 40 HRC |
| Surface hardness | After carburize, quench, temper | 58 - 62 HRC |
| Effective case depth | To 550 HV1 | 0.8 - 2.0 mm, by module or section |
| Retained austenite | Case, after temper | Below 25 % by volume |
These figures describe the grade in the stated condition and are intended as planning values. The binding numbers are those agreed on the order. Note that tensile properties for alloy structural steel are quoted at a defined reference section; a 150 mm forging cannot be expected to reproduce the properties of a 25 mm test bar, and for heavy sections a hardenability test or a properties-at-section agreement is more informative than a standard tensile certificate.
Carburizing Cycle, Quenching and Tempering
Because the grade carries both nickel and molybdenum, it tolerates a wider carburizing window than a plain chromium steel, but it also retains more austenite after quenching, so the tempering and any sub-zero step must be planned rather than added as an afterthought. A workable cycle for a medium gear is set out below; time at temperature is calculated from the required case depth, since carbon diffusion follows a square-root relationship with time and doubling the case depth takes roughly four times the soak.
| Step | Typical parameter | Note |
|---|---|---|
| Normalize or isothermal anneal | 880 - 920 deg C | Before rough machining; target 170 - 210 HB |
| Carburize | 900 - 930 deg C, carbon potential 0.8 - 0.9 % | Boost then diffuse; avoid surface carbon above 1.0 % |
| Diffuse | Same temperature, potential reduced to 0.7 - 0.75 % | Removes grain-boundary carbide network |
| Quench | 830 - 850 deg C into agitated oil | Reheat from a slow cool for finer grain, or direct quench |
| Sub-zero, where specified | -60 to -80 deg C, 1 - 2 h | Reduces retained austenite, stabilises dimensions |
| Temper | 170 - 200 deg C, 2 h minimum | Keeps case hardness above 58 HRC |
Avoid two traps. Do not temper this grade in the 400-550 deg C range in an attempt to soften the core; that is exactly the window in which residual phosphorus and tin segregate to grain boundaries and embrittle the steel, and molybdenum only delays the process rather than preventing it. And do not judge the case by a file or a portable hardness tester alone: a 60 HRC reading can sit on a case with a carbide network that will spall, or on a layer thin enough to wear through before the first inspection interval.
Forging, Annealing and Machining Sequence
Forging is carried out from the 1050-1180 deg C range with a finish temperature not below about 850 deg C, followed by controlled slow cooling for sections over roughly 80 mm to avoid internal cracking from hydrogen and thermal stress. Forging ratio matters for gear blanks: a ratio below about 4:1 in the tooth region leaves casting-type segregation stringers that show up as banding after carburizing and as scatter in fatigue results. Buyers of critical parts should state a minimum forging ratio rather than accepting whatever reduction the forge happens to apply.
Machining follows normalize, rough turn, semi-finish, then finish after heat treatment. Because the grade is nickel-bearing, it work-hardens readily; keep the depth of cut above the work-hardened layer left by the previous pass, use sharp coated carbide for turning and tough micrograin carbide for interrupted cuts, and avoid dwelling at the start of a cut. Grinding stock of 0.3-0.4 mm on bearing journals and 0.10-0.15 mm on gear flanks is typical, with the flanks ground after hardening to correct distortion. Any hole, keyway or thread that would be damaged by a 60 HRC case should be masked with stop-off compound before carburizing, or machined afterwards.
Where the Grade Earns Its Cost
Heavy-duty gearing is the primary application. Industrial gearbox pinions and wheels, crane and hoist gearing, mill drives and extruder gearboxes all use nickel-molybdenum carburizing steels because the tooth root must survive repeated bending at high torque while the flank resists pitting; a 2% Ni, 0.25% Mo balance gives a case that holds 58-62 HRC over a core that stays at 30-40 HRC with good impact energy. The same combination suits the European 18CrNiMo7-6 family of case-hardening steels, which occupies a comparable position in gear design.
Vehicle and off-highway drivetrains use the grade for final drive gears, differential pinions, axle shafts and synchronizer parts, where shock loading is routine. Mining and mineral processing equipment - crusher drive gears, conveyor reducers, dragline and shovel gearing - selects it for the same reason plus the need to tolerate dust-contaminated lubricant, which turns a marginal pitting problem into a rapid wear problem. Wind turbine gearboxes specify nickel-molybdenum carburizing steels for planet and helical stages because the design life is measured in decades and the case must resist micropitting under boundary lubrication. Marine and offshore deck machinery, winches and steering gear use it where salt atmosphere demands protection by coating or enclosure rather than by the steel itself.
Cleanliness, Hydrogen and Embrittlement Control
Two failure mechanisms are worth writing into a specification. The first is non-metallic inclusion content: oxide and silicate stringers in a gear tooth root act as crack initiators, and the difference between a 10-year and a 3-year gear life is often cleanliness rather than hardness. For critical parts, require inclusion ratings to a recognized chart, with the assessment method stated on the certificate, and require the samples to be taken from the product rather than from a separate test ingot.
The second is hydrogen. Large forgings that are cooled too quickly after forging, or that are pickled without an adequate bake, can retain hydrogen and crack hours or days later - the classic delayed failure that appears only after the part is in the warehouse. Specify a hydrogen bake for sections above 80 mm, control the cooling rate after forging, and avoid acid pickling of hardened parts; if pickling is unavoidable, require a dehydrogenation bake at 200-250 deg C within a defined time after the pickle.
Inspection, Acceptance and Storage
An acceptance package that actually protects the buyer contains the mill certificate with heat number and full analysis, the forging record with ratio and post-forge cooling, the heat treatment record per load with carbon potential and temperatures, and finished-part inspection covering surface hardness, effective case depth to 550 HV1, core hardness, case microstructure for carbide network and retained austenite, and a dimensional report. Each of these closes a specific failure path; a package missing the heat treatment record cannot be used to investigate a short case, and a package missing the forging ratio cannot be used to explain banding.
Storage is a smaller but real issue. This is not a stainless grade, so bars and finished parts must be kept under cover, off the floor and away from condensation; a 1.2% Cr steel left in a damp yard develops surface pitting within weeks, and rust pits on a gear flank become pitting-fatigue origins after the part enters service. Carburized and ground parts should be protected with a temporary coating and wrapped, and should not be stored in contact with dissimilar metals in a humid atmosphere.
FAQ
Q: Is 18CrMnNi2Mo a stainless or corrosion-resistant steel?
No. At roughly 1.2% Cr it cannot form a passive chromium oxide film; it rusts in humid air and is not suitable for acid, alkali or seawater service without coating or a change of material.
Q: What heat treatment does 18CrMnNi2Mo need before machining?
A normalize or isothermal anneal at 880-920 deg C, giving about 170-210 HB; a 1050-1150 deg C solution treatment belongs to austenitic stainless practice and would coarsen the grain of this steel.
Q: Why is molybdenum added to this carburizing steel?
Molybdenum raises hardenability and, more importantly, suppresses temper embrittlement by limiting grain-boundary segregation of phosphorus, which matters for large sections that cool slowly after tempering.
Q: What case depth should be specified for a gear?
A common rule is 0.15-0.20 times the normal module for case-hardened gears, giving roughly 0.8-2.0 mm on medium modules, always measured to 550 HV1 on a coupon from the same load.
Q: Can the grade be welded?
Only with preheat around 200 deg C, low-hydrogen consumables and a post-weld temper at 600-650 deg C, and never on a carburized surface, which must be ground back to core material first.
Q: How should 18CrMnNi2Mo bar stock be stored?
Under cover, off the ground and protected from condensation; the grade has too little chromium to resist atmospheric rusting, and surface pits become fatigue origins once the part is in service.




