ABS Grade FQ47 is the highest strength grade in the ABS extra-high-strength shipbuilding steel family. Plates of this grade combine a 460 MPa minimum yield strength with guaranteed Charpy V-notch impact performance at -60 °C, which is why they are selected for hull structures, offshore drilling platforms, platform pipe joints and other components that must keep their load-carrying capacity in cold marine service.
What ABS Grade FQ47 Means in the ABS Grade System
In the ABS grade designation the first letter refers to the guaranteed impact test temperature and the number refers to the minimum yield strength in newtons per square millimetre. FQ47 therefore describes an extra-high-strength hull structural steel with a 460 MPa minimum yield strength that must pass Charpy V-notch impact testing at -60 °C. It is the top step of the ABS extra-high-strength series that runs from AQ47 through DQ47, EQ47 and FQ47, each step lowering the guaranteed impact test temperature. The grade is normally delivered in the quenched and tempered condition, and the heat treatment mark on every plate is QT.
Chemical Composition of ABS Grade FQ47
The table below lists the ladle analysis limits for the grade. Values are maximum percentages, and the limits are applied to a fully killed, fine grain treated steel.
| Element | C | Si | Mn | P | S | N |
|---|---|---|---|---|---|---|
| Limit, % | 0.18 max | 0.55 max | 1.60 max | 0.020 max | 0.020 max | 0.020 max |
Because phosphorus and sulphur are each restricted to 0.020 %, FQ47 is produced with a low residual content. The tight impurity control is what makes the -60 °C impact energy repeatable in thick plates, and it also lowers the risk of lamellar tearing in heavily restrained welded joints. Manganese is held at 1.60 % maximum so that strength is achieved together with, not at the expense of, low-temperature toughness.
Mechanical Properties and Low-Temperature Toughness
| Property | Requirement |
|---|---|
| Yield strength, min | 460 MPa |
| Tensile strength | 570 - 720 MPa |
| Elongation, min | 17 % |
| Impact test temperature | -60 °C, Charpy V-notch |
| Typical delivery condition | Quenched and tempered (QT) |
The tensile range is narrow compared with the yield requirement, so the plate has to be produced under close process control: quench severity, tempering temperature and tempering time all have to be held within a defined window, and each heat is verified by tensile and impact testing. Welding consumables and heat input should be selected so that the weld metal and the heat affected zone reach the same 460 MPa minimum yield strength without losing the low-temperature impact energy that the grade is specified for.
Supply Range, Delivery Condition and Optional Tests
Thickness: 6 mm to 240 mm
Width: 1500 mm to 4020 mm
Length: 3000 mm to 27000 mm
Delivery conditions: as rolled (AR), thermo-mechanical control processed (TMCP), normalised (N) and quenched and tempered (Q+T)
Optional services: ultrasonic examination, through-thickness testing in the Z15, Z25 and Z35 grades, Charpy V-notch impact testing, third party inspection, shot blasting and shop priming
Dimension and test combinations outside the range above are usually handled as a project specific agreement, with the inspection regime fixed before rolling so that the plate is tested in the condition in which it will be used.
Typical Applications
ABS Grade FQ47 plate is used where a structure has to carry high loads at low ambient temperature. Typical applications include offshore oil and drilling platforms, hull structures and structural parts in shipbuilding and ship repair, platform pipe joints and node components, deck and hatch coaming structures, crane pedestals and heavy lifting frames. In all of these cases the grade is chosen because the design combines a high static stress level with a low design service temperature, a combination that ordinary hull structural grades cannot satisfy.
FAQ About ABS Grade FQ47 Steel Plate
Q: What does the letter F in ABS Grade FQ47 specify?
It fixes the guaranteed impact test temperature. F indicates that the Charpy V-notch test must be carried out at -60 °C.
Q: What is the minimum yield strength of ABS FQ47?
The minimum yield strength is 460 MPa, the tensile strength range is 570 to 720 MPa, and the minimum elongation is 17 %.
Q: Is ABS FQ47 always supplied quenched and tempered?
The grade is normally produced in the quenched and tempered condition and marked QT, which is the condition in which the tensile and impact properties are certified.
Q: Which thickness range can be supplied?
Plates are commonly supplied from 6 mm to 240 mm thick, 1500 mm to 4020 mm wide and 3000 mm to 27000 mm long.
Q: Can the plates be ordered with through-thickness testing?
Yes. Z15, Z25 and Z35 through-thickness testing can be specified for plate that will be welded in a highly restrained joint.
Q: What impact test does the grade require?
A Charpy V-notch impact test is required, performed at -60 °C, and the result is certified heat by heat.




