Mar 22, 2024 Leave a message

Choosing Grain-Oriented Silicon Steel: Grade and Thickness

What "GO" Means and Why Type Selection Starts There

GO silicon steel, grain-oriented electrical steel, is a cold-rolled sheet in which a high-temperature secondary recrystallisation treatment has produced a sharp cube-on-edge texture, so that the easy magnetisation direction lies along the rolling direction. That texture is what separates it from non-oriented electrical steel: loss in the rolling direction falls to roughly a quarter of a comparable non-oriented grade, while loss measured across the rolling direction rises steeply. Selecting a "type" of GO steel therefore means settling four coupled decisions at once - nominal thickness, guaranteed specific total loss, induction at a stated magnetising force, and the surface coating - and then matching them to the core geometry, the operating flux density and the frequency of the machine or transformer being built.

The commercial consequence is that two coils with the same nominal grade in different thicknesses, or the same thickness with different induction classes, are not interchangeable. A grade chosen only by loss figure can leave a design short of induction, forcing a larger core; a grade chosen only by induction can push loss past what the cooling system can remove. The selection sequence below is written from the position of a buyer who must justify the choice against a guaranteed performance figure.

Step One: Fix the Operating Flux Density and Frequency

Start with the actual duty, not with the catalogue. A distribution transformer limb usually runs at 1.5-1.7 T at 50 Hz or 60 Hz; a large power transformer may be pushed to 1.75-1.85 T to reduce mass; a 400 Hz aircraft or marine transformer runs at far lower flux because loss scales faster than linearly with frequency. Write down the design flux density, the fundamental frequency, and whether the flux is purely alternating or contains a DC bias component - a bias, as in some rectifier and inverter-fed duty, shifts the operating point along the B-H curve and effectively burns part of the induction headroom before the core saturates.

Frequency also decides whether thin gauge is worth its cost. At 50 Hz the eddy-current share of total loss in a 0.30 mm sheet is moderate; at 400 Hz it dominates, and the move from 0.35 mm to 0.20 mm or 0.15 mm produces a large absolute saving. At line frequency the same move buys a smaller gain, and the higher shearing count and lower stacking factor can consume it. A defensible rule is to justify any step down in thickness by a calculated loss saving over the life of the unit, using the guaranteed loss of each candidate grade rather than a generic percentage.

Step Two: Read the Loss Guarantee Correctly

Specific total loss is quoted in W/kg at a defined peak flux density and frequency, measured on an Epstein frame to IEC 60404-2 or on a single-sheet tester to IEC 60404-3. Grain-oriented grades are conventionally compared at 1.7 T and 50 Hz, but catalogues also list 1.5 T figures, and mixing the two references is the most common source of miscomparison. Before any quotation is evaluated, confirm that every candidate is quoted at the same flux density, the same frequency and the same test method, and that the value is a guaranteed maximum rather than a typical value.

The gap between a guaranteed maximum and a mill's typical value is real and is not dishonesty: the standard permits a tolerance band, and mills centre their process inside it. A buyer who needs a tight building factor should ask for the guaranteed figure, then check the inspection certificate of the actual heat, and should treat a quoted "typical" as an indication only. The difference between 1.05 W/kg and 1.20 W/kg at the same thickness is roughly a grade step, and it translates into a measurable difference in no-load loss and temperature rise in the finished unit.

Step Three: Match Thickness, Loss and Induction

The table below sets out the working envelope of commercially supplied grain-oriented sheet. Values are industry-common ranges for orientation purposes; the binding numbers are always those of the ordered grade and its certificate. The loss column refers to 1.7 T at 50 Hz, and induction is stated as B at 800 A/m, the usual acceptance point for grain-oriented material.

Nominal thickness, mm Typical guaranteed loss, W/kg at 1.7 T, 50 Hz Typical induction B at 800 A/m, T Preferred duty
0.15-0.18 0.60-0.85 1.88-1.94 high-frequency transformers, mobile units
0.20-0.23 0.75-1.00 1.87-1.95 large power transformers, loss-critical designs
0.27-0.30 0.95-1.25 1.85-1.93 distribution transformers, general power units
0.35 1.20-1.60 1.80-1.90 cost-driven distribution and small power units

Two selection errors recur. The first is choosing the lowest loss grade available and then discovering that its induction class is also the lowest, so the core must be made larger and the saving evaporates. The second is choosing a high-induction grade for a design that never exceeds 1.6 T, where the extra cost buys nothing. The correct comparison is a short list of two or three candidate grades evaluated on total evaluated cost: steel mass at the design flux density, plus labour per lamination, plus the capitalised value of the guaranteed loss over the expected service life.

Step Four: Choose the Coating Before the Core Is Built

Insulating coatings on grain-oriented sheet are classified in ASTM A976, and the practical choice is between thin organic resin, half-organic, and inorganic ceramic types. Interlayer resistance is the property that matters, because it limits eddy currents flowing from sheet to sheet; a coating that survives stress-relief annealing is mandatory if the core will be annealed after cutting or winding, whereas an organic resin burns away and leaves bare, short-circuiting surfaces. Inorganic coatings give the highest interlayer resistance and the best anneal survival, at the cost of a slightly lower stacking factor and a harder, more abrasive surface that wears tooling faster.

Coating choice also interacts with the assembly method. Wound cores that are annealed after winding need a coating that tolerates the full thermal cycle plus the mechanical abrasion of winding tension. Stacked cores that are varnished or adhesive-bonded can use a thinner coating, because the bond line provides part of the interlayer insulation. Specify the coating type by its standard classification and not only by a colour description, since colour varies between mills for functionally identical products.

Step Five: Geometry, Width and Flatness Constraints

Grain-oriented sheet is anisotropic, so the cutting plan is part of the metallurgy. Strips for limbs should be slit with the rolling direction along the strip axis; yokes should be nested so that the flux turn is shared between a 45-degree mitred cut and the rolling direction, rather than being forced through a full 90-degree turn against the hard axis. Step-lap joints, with the butt gaps of successive layers staggered over two, three or five steps, reduce both exciting current and magnetostrictive noise compared with a single aligned gap.

Width availability constrains the design more often than buyers expect. Standard slitting ranges and the need to cut yokes from the same coil as limbs may force a lamination width that is not the theoretical optimum, and narrow strips cut from a wide coil carry a proportionally larger cut-edge damage zone. Camber, edge waviness and flatness tolerances in the applicable GB/T 2521 part should be reviewed against the customer's own stacking practice: a coil that passes the standard can still produce a noisy, low-stacking-factor core if the flatness is at the limit of the tolerance and the shop clamps hard.

Step Six: Define Acceptance Before Ordering

Order acceptance criteria belong in the purchase specification, not in a later dispute. A workable set covers grade and thickness tolerance, coating type and minimum interlayer resistance, guaranteed specific total loss and induction with the test method named, burr height on sheared parts, flatness and camber limits, winding or coil mass, edge condition, and the documents to be supplied - inspection certificate with heat number, dimensional record, and where required a third-party witnessed magnetic test. Sampling plan and retest rules should be agreed in advance, because magnetic properties vary along a coil and a single grab sample is weak evidence either way.

For annealed cores, add a post-anneal check of flatness, coating integrity and loss. Stress-relief annealing at approximately 750-820 degrees C in a controlled atmosphere restores the loss and permeability damaged by cutting and bending, but it can also warp a poorly supported stack and can carbon-contaminate a charge that is not protected. Loss measured before annealing should never be presented as the delivered value.

Step Seven: Account for the Building Factor

The finished core never reaches the loss of the sheet it was made from. Joints, cut-edge damage, clamping stress, bolt holes and stacking imperfections add loss, and the ratio of built-core loss to the sum of the sheet losses - the building factor - commonly falls between about 1.10 and 1.35 for stacked transformer cores, with better figures for well-designed step-lap joints and worse ones for small cores with a high proportion of joints. Thin, high-induction grades tend to show a somewhat higher building factor because they are more sensitive to handling stress, which is one reason a specification written purely around the sheet grade can fail at the finished-core test.

Designers should therefore reserve part of the loss margin for the building factor, and buyers should judge a supplier on the as-built core loss rather than on the coil certificate alone. Where the guarantee is on the finished transformer, the selection of grade and thickness must be made with the building factor already included.

FAQ

Q: What is the difference between grain-oriented and non-oriented silicon steel?
Grain-oriented sheet has a cube-on-edge texture that gives very low loss along the rolling direction and high loss across it, so it suits transformer cores where flux follows a known path. Non-oriented sheet has acceptable loss in all in-plane directions and is used in motors and chokes.

Q: Which thickness should be chosen for a 50 Hz distribution transformer?
Most designs land between 0.27 mm and 0.35 mm. The thinner end is chosen when the guaranteed loss and temperature rise are tight; the thicker end when first cost dominates and the loss penalty is acceptable in the evaluated cost.

Q: Should the loss figure be quoted at 1.5 T or at 1.7 T?
Grain-oriented grades are conventionally compared at 1.7 T and 50 Hz, and many catalogues also list 1.5 T values. Any comparison is valid only if every candidate uses the same flux density, frequency and test method, and quotes a guaranteed maximum rather than a typical value.

Q: Why does the coating type matter if the sheets are already insulated by oxide?
The mill-applied coating provides a controlled, consistent interlayer resistance and, in the inorganic and half-organic types, survives stress-relief annealing. A coating that burns off during annealing leaves the stack with bare, electrically connected surfaces and high eddy-current loss.

Q: Does a lower-loss grade always give a smaller transformer?
No. Lower loss and lower induction often come together in the same grade, and a design limited by induction will need more iron. Evaluate candidates on core mass at the actual design flux density plus capitalised loss, not on the loss figure alone.

Q: How is as-built core loss verified?
By a no-load loss test on the assembled core or finished unit, compared with the design value that already includes the building factor, and by checking the sheet certificate at the same flux density and frequency used in the design calculation.

Send Inquiry

whatsapp

phone

Email

Inquiry