Mar 22, 2024 Leave a message

How to Pack Electrical Silicon Steel for Safe Export Delivery

Electrical silicon steel cannot be packed like ordinary mild steel sheet. Its surface carries a thin insulating coating that keeps core loss low, the strip is produced in thin gauges where a small edge dent becomes a lamination stacking problem, and any moisture that reaches the surface during a long sea voyage corrodes the edges and destroys the insulation resistance of the coating. Packing has three jobs: protect the coated face and the edges, exclude moisture, and keep the stack rigid enough that it cannot shift inside the container.

Why Electrical Silicon Steel Needs Its Own Packing Method

Electrical steel is supplied as cold rolled grain oriented (CRGO) material, where the magnetic properties are best along the rolling direction, or as cold rolled non-oriented (CRNGO) material, where the properties are more uniform in the plane of the sheet. In both cases the delivered magnetic quality depends on the microstructure staying intact, and that microstructure is damaged by plastic deformation. A twist that leaves no visible mark, a sling point that kinks the coil, or a stack dropped on one corner can all raise hysteresis loss in the finished core.

Thin gauges make the problem worse. A 0.35 mm or 0.50 mm strip has very little bending stiffness of its own, so the edge is easily turned over, and once an edge is burred the laminations will not stack flat. The insulating coating is equally fragile: it is a thin oxide or varnish layer, and abrasion, water staining or acid attack removes it locally, which shows up later as short circuits between laminations and local overheating in the core.

For these reasons the packing has to do more than hold the weight of the steel. It has to immobilise the stack, cushion every edge, and keep the air around the steel dry for the entire transit, including the period when the container cools at night and any free water in the air condenses on the coldest surface.

Packing Materials and What Each One Does

A complete export pack uses several layers, each with a defined function. Substituting one layer for another, or skipping one to save weight, is the usual reason a consignment arrives stained.

Material Function Where it is used
VCI corrosion inhibitor film Releases a vapour that protects bare cut edges and coil faces from rust Inner wrap in direct contact with the steel
Desiccant bags Absorb residual moisture sealed inside the wrap Between layers and inside the crate
Bubble wrap or PE foam Cushions impact and shock in handling Around the coil body and the sheet faces
Edge and corner protectors Prevent edge damage and cut strapping from marking the steel Crate corners, coil edges and eye
Kraft paper or heavy plastic film Outer moisture barrier and dust barrier Outside the VCI layer
Steel strapping Keeps the stack compressed so it cannot fan out Around the coil or the sheet stack
Wooden crate or pallet Rigid base and side support for lifting and stacking Outer package, heat treated to the wood packaging standard

Step-by-Step Packing Procedure

Collect the materials first. Have the VCI film, desiccant, foam, edge protectors, strapping, crate and lifting gear ready before the steel is opened, so that the material is never left unprotected on the floor.

Inspect and clean the steel. Wipe off any moisture, dust or fingerprints and reject any piece with a visibly damaged coating. A stain sealed inside the pack becomes a corrosion cell.

Wrap the steel in the inner layer. Apply the VCI film so that it covers the whole coil or stack with an overlap on every seam, then wrap the coil body in bubble wrap or PE foam so that impact energy is absorbed before it reaches the steel.

Fit the foam sheets. Cut closed-cell foam to the size of the stack and place it against the flat faces and the coil edges, so the steel never touches the crate wall directly.

Place the pack in the crate. Load the wrapped coil or stack onto the wooden crate or pallet so that the weight is carried by the base, with the eye of a coil protected against ovalisation.

Fill every gap. Pack the remaining space with foam or bubble wrap so that nothing can shift when the crate is tilted or lifted. Movement in transit is what produces bright rub marks and edge damage.

Add the desiccant and close the barrier. Place the calculated number of desiccant bags inside the wrap before sealing it, then close the outer kraft or plastic layer over the whole pack.

Strap and seal the crate. Apply steel strapping over the edge protectors and fasten the crate lid so that all seams and corners are closed. Strapping placed directly on the steel, without a protector, crushes the edges of thin strip.

Mark the package. Show the grade, gauge, coil or sheet number, net and gross weight, the handling symbols and the centre of gravity on the crate, so that the receiving site can lift and unload without opening the pack.

Moisture Control and Corrosion Protection

Sea transport exposes a container to large temperature swings. Warm humid air loaded at the port cools during the voyage, and the water it releases condenses on the coldest surface inside, which is usually the steel itself. This container rain is the main cause of edge rust on thin electrical steel. Three measures control it: keep the moisture out with a sealed barrier, absorb what remains with desiccant, and avoid loading damp or wet cargo into the same container.

Wooden packing should be dry before it is used, because a damp pallet is a reservoir of water sitting directly under the steel. Crates should be heat treated and marked to the international wood packaging standard so that they clear customs without a delay that would leave the container sitting on a quay. Where a consignment is expected to spend an extended period in a humid climate, a desiccant allowance based on the volume of air sealed inside the pack, rather than a fixed number of bags, gives a safer result.

Crates, Handling and Container Loading

Handling practice matters as much as the pack itself. Coils should be lifted with a proper C-hook or a spreader, never with a chain through the eye, and sheets should be lifted on a rigid pallet so that the bundle does not sag. Crates must not be dropped, and a crate that has been dropped should be opened and inspected before it is shipped.

Container Internal length x width x height Loading note
20 ft general purpose 5898 mm x 2352 mm x 2393 mm Suits medium coils and sheet crates; check the floor point loading
40 ft general purpose 12032 mm x 2352 mm x 2393 mm Suits long sheet bundles; lash the load to prevent fore and aft movement

Inside the container the packs are lashed to the lashing points so that they cannot slide during handling and road transport, and heavier crates go at the bottom. Storage before shipment should be under cover, on dry dunnage and away from the container doors, and any pack that has been opened should be resealed with fresh desiccant rather than closed with the original material.

Frequently Asked Questions

Q: Why can electrical silicon steel not be packed like ordinary steel sheet?
Because it is thin, its magnetic properties are sensitive to deformation and its surface carries a thin insulating coating that is destroyed by moisture, abrasion and edge damage, so the pack must immobilise and dry the material as well as carry its weight.

Q: What is the most important layer in the pack?
The inner VCI film, because it protects the bare cut edges from rust while the outer barrier keeps liquid water away from the whole pack.

Q: How many desiccant bags are needed?
The number depends on the volume of air sealed inside the wrap and the length of the voyage, so it is calculated for each consignment rather than fixed in advance.

Q: Can CRGO and CRNGO coils be shipped in the same container?
Yes, but each coil needs its own sealed pack, and grain oriented coils should be kept flat and protected against twisting since their best magnetic properties lie along the rolling direction.

Q: What causes rust spots on arrival even when the crate looks dry?
Condensation inside the sealed pack, usually caused by loading warm humid air or damp wood, is the common cause; a sealed barrier with a correctly sized desiccant load is the remedy.

Q: Is a wooden pallet acceptable as the only package?
Only for short inland journeys. For sea freight a crate with side support, edge protection and a moisture barrier is needed to protect the edges and keep the stack rigid.

Q: How should a dropped or opened pack be treated?
Open it, inspect for edge damage and coating damage, and reseal with fresh foam, film and desiccant instead of reusing the original materials.

Send Inquiry

whatsapp

phone

Email

Inquiry