Mar 22, 2024 Leave a message

ASTM-A516-A516M Standard Specification.pdf

ASME SA516 Gr.70 Plate: Composition, Toughness, Weldability

What SA516 Grade 70 Covers

SA516 Gr.70 is a carbon steel plate specification for welded pressure vessels serving at moderate and lower temperatures. It appears in ASME BPVC Section II Part A as SA516 and in ASTM A516/A516M as Grade 70; the two documents are technically aligned, which is why a single mill certificate is normally accepted under both. The grade sits in a family of four - Grades 55, 60, 65 and 70 - that share the same chemistry philosophy and differ mainly in tensile strength level. Grade 70 is the highest of the four and the most widely ordered.

The number 70 is a strength class designation inherited from the 70 ksi minimum tensile requirement, not a thickness, a hardness or a carbon level. That distinction matters in procurement, because a buyer who specifies "SA516-70" without stating thickness, heat treatment condition, impact requirements and delivery condition has specified perhaps half of what the vessel design actually needs.

Chemical Composition and How the Four Grades Differ

SA516 is a plain carbon-manganese steel with deliberate limits on residual elements. Grade 70 permits a slightly higher carbon and manganese level than the lower grades, which is how the extra tensile strength is obtained without alloying additions. Silicon is specified as a deoxidation control and is normally held in a band that guarantees a fully killed, fine-grained practice.

Element Gr.55 / Gr.60 Gr.65 Gr.70 Notes for the buyer
Carbon (C), max 0.28 / 0.26% 0.28% 0.27% Lower carbon improves toughness and weldability
Manganese (Mn) 0.60–1.20% 0.85–1.20% 0.85–1.20% Strength and toughness balance
Silicon (Si) 0.13–0.45% 0.13–0.45% 0.13–0.45% Killed steel; deoxidation indicator
Phosphorus (P), max 0.035% 0.035% 0.035% Embrittlement control; tighter limits are common in practice
Sulphur (S), max 0.035% 0.035% 0.035% Through-thickness and HIC behaviour
Copper (Cu), max 0.40% 0.40% 0.40% Residual from scrap; relevant in sour service
Nickel (Ni), max 0.40% 0.40% 0.40% Residual
Chromium (Cr), max 0.30% 0.30% 0.30% Residual
Molybdenum (Mo), max 0.08% 0.08% 0.08% Residual; above this it becomes an alloy steel

Two practical points follow from this table. First, the maxima are maxima: a mill that produces 0.16% C and 0.010% P in a Grade 70 heat is fully compliant and will deliver noticeably better toughness and weldability than a heat sitting at the limits. Second, residual element control is the difference between a plate that performs in sour service and one that does not, and those residuals are not visible in the headline tensile figures.

Mechanical Properties and the Thickness Effect

SA516 Gr.70 is specified by tensile range, minimum yield and minimum elongation, and the requirement is tied to plate thickness because thicker sections cool more slowly and develop coarser structures. Nominal values for the grade are 485–620 MPa tensile, 260 MPa minimum yield, and 17% minimum elongation on a 200 mm gauge length (21% on a 50 mm gauge length). Plates are available up to about 205 mm thick, and above roughly 40 mm the specification requires the plate to be supplied in the normalized condition.

Property Requirement for Gr.70 Engineering consequence
Tensile strength 485–620 MPa Sets the allowable stress used in the vessel calculation
Yield strength, min 260 MPa Governs design stress at temperature; extra margin over Gr.60
Elongation, min (200 mm) 17% Formability and strain capacity during rolling
Elongation, min (50 mm) 21% Same, on a shorter gauge
Normalizing threshold Above 40 mm, per specification Thick plate is supplied normalized as standard
Product analysis tolerance Permitted deviations from ladle analysis Check the product analysis, not only the heat analysis

The upper end of the tensile range deserves attention. A plate with a tensile of 615 MPa is compliant with the specification but has less elongation and less toughness reserve than one at 510 MPa. Where the vessel will be formed cold, or where the design relies on impact energy at low temperature, a buyer is within his rights to ask for a target closer to the middle of the range. This is a normal commercial request and is far easier to agree before rolling than after delivery.

What the "N" Suffix Changes

SA516 Gr.70N denotes plate that has been normalized: heated to a temperature above the upper critical point, held to dissolve and homogenise the structure, and cooled in still air. The result is a finer, more uniform ferrite-pearlite structure with a more even carbide distribution, lower residual stress and better notch toughness. Normalizing also reduces the scatter in properties across a large plate, which is exactly what a pressure vessel fabrication needs because the shell will be welded in the as-supplied condition.

The commercial consequences are straightforward. Normalized plate costs more, because it consumes a full extra thermal cycle and furnace capacity, and it is not available from every mill at short notice in heavy gauges. It is nevertheless unavoidable above the thickness threshold and is frequently specified below it for low-temperature service, for cold-formed heads, and for any vessel where impact testing at a sub-zero temperature is a design requirement. When comparing offers, confirm whether the quoted price is for as-rolled or normalized plate; the two are not interchangeable and the difference is often the whole of the price gap between competing bids.

Normalizing also imposes a fabrication duty. Any subsequent hot forming above the tempering range, or any welding with a high heat input followed by no post-weld treatment, will partly undo the benefit. Fabrication procedures should state the maximum hot-forming temperature and the post-weld heat treatment window, and the plate certificate should be matched to the actual forming route the shop will use.

Weldability and Fabrication Practice

SA516 Gr.70 is readily weldable by shielded metal arc, submerged arc, gas metal arc and flux-cored processes, which is a large part of why it dominates pressure vessel fabrication. The carbon equivalent is low enough that preheat is often unnecessary in thin sections, but the qualification is thickness and restraint dependent: heavy plate, high restraint joints and cold shop conditions all call for preheat, and the exact figure should come from the qualified welding procedure rather than from a generic table.

Three points are worth writing into the fabrication specification. First, hydrogen control: use low-hydrogen consumables for all thicknesses above the routine range, bake and store them correctly, and keep the joint dry, because hydrogen-assisted cracking in thick SA516 sections is a real and expensive failure mode. Second, heat input: excessive heat input coarsens the heat-affected zone and reduces toughness at the fusion line, which is precisely where impact tests are taken. Third, repair welds: excavation and repair concentrate restraint, so repair procedures generally need a higher preheat and a stricter interpass control than the original joint.

Post-weld heat treatment is decided by thickness, by the applicable construction code and by the service environment. Where PWHT is applied, the holding temperature and time must be consistent with the plate's original normalizing condition, and the plate must not be re-austenitized accidentally by an over-temperature excursion.

Impact Toughness, Low-Temperature Duty and Sour Service

SA516 as a specification does not by itself guarantee a Charpy value at a given temperature. Impact testing is a supplementary requirement, agreed between purchaser and mill, and stated as a test temperature and a minimum absorbed energy. This is the single most misunderstood part of the grade: a certificate showing only tensile and yield results tells you nothing about the ductile-to-brittle transition behaviour of that plate.

For service around −30 °C, normalized Grade 70 with specified impact energy is the usual route, and many mills routinely demonstrate capability well below that on a normalized product. For genuinely low-temperature vessels - liquefied gas duty in the −40 to −70 °C region - the correct answer is normally a dedicated low-temperature grade such as those in GB/T 3531 or an ASME impact-tested option, not a heavily downgraded SA516 assumption. Matching the grade to the design minimum temperature is a design engineer's decision and should not be inferred from a supplier's claim.

Sour service is a separate qualification again. Wet H2S environments introduce hydrogen-induced cracking and sulphide stress cracking risks that plain SA516 is not automatically qualified for. The usual response is a plate with tighter sulphur and residual control, calcium-treated for inclusion shape control, and qualified by HIC testing to the relevant standard and by SSC testing where the design requires it. Ordering "SA516 Gr.70, sour service" without specifying the HIC test acceptance criteria and the sulphur ceiling leaves the requirement unenforceable.

Cross-Standard Comparison: Q345R, P355GH, P265GH and A285 Gr.C

Buyers frequently ask whether a Chinese, European or Indian grade can be substituted. The honest answer is that chemistry and strength can be close, while the qualification basis is not identical, so substitution always requires engineering approval.

Grade Standard Typical chemistry Typical mechanical level Substitution reality
SA516 Gr.70 ASTM A516 / ASME SA516 C 0.27 max, Mn 0.85–1.20%, Si 0.13–0.45% 485–620 MPa tensile, 260 MPa yield Reference grade
Q345R GB/T 713 C 0.20 max, Mn 1.20–1.60%, P 0.025 max, S 0.015 max 500–630 MPa tensile, 325 MPa yield Often meets or exceeds SA516 Gr.70; still needs approval as a substitute
P355GH EN 10028-2 C 0.20 max, Mn 1.00–1.60% 510–650 MPa tensile, 355 MPa yield Higher yield; closer to a different design assumption
P265GH EN 10028-2 C 0.20 max, Mn 0.80–1.40% 410–530 MPa tensile, 265 MPa yield Closest to SA516 Gr.60, not Gr.70
A285 Gr.C ASTM A285 Low carbon, no fine-grain requirement 380–515 MPa tensile Lower grade; SA516 Gr.70 is an upgrade, not an equal

Two traps recur. The first is treating Q345R and SA516 Gr.70 as equivalents because the numbers look close: Q345R is tighter on phosphorus and sulphur and higher on yield, so the plate may be mechanically stronger than the design assumed, which affects weld procedure qualification and forming loads. The second is accepting a higher grade as a substitute for a lower one without documentation - an upgrade still changes the material certificate, the weld qualification and sometimes the PWHT requirement, and needs a formal engineering acceptance rather than a shipping decision.

Tolerances, Marking and Documents to Check on Arrival

Dimensional tolerance for pressure vessel plate is not a detail. Shell fit-up, head forming and nozzle orientation all depend on thickness consistency, and EN 10029 classe tolerances or the equivalent contractual table should be stated in the order if the fabricator's rolling plan is sensitive to it. Thickness should be checked at the prescribed measuring points, not at the plate edge where the mill roll crown leaves a thinner band.

A complete delivery package for SA516 Gr.70 normally contains: the mill test certificate with heat number and product analysis, the heat treatment record showing normalizing charge and temperature, the impact test report where specified, the marking that transfers the heat number to the cut piece, and the dimensional inspection record. The marking point is easy to overlook and expensive to lose: once a plate is cut, the only link between the shell course and the certified heat is the transferred marking, and a fabricator who cannot show that link cannot demonstrate code compliance.

Finally, verify that the certificate grade matches the order in every respect: grade number, normalized condition, impact requirement and any supplementary toughness or HIC clause. A certificate that says simply "SA516-70" against an order that specified "SA516-70N with 27 J at −30 °C" is not a compliant document, however good the plate may be.

FAQ

Q: Is SA516 Gr.70 the same as ASTM A516 Grade 70?
Yes in technical content. SA516 is the ASME BPVC Section II Part A designation and A516/A516M is the ASTM designation; the requirements are aligned and one certificate commonly serves both.

Q: At what thickness must SA516 Gr.70 be normalized?
The specification requires normalizing for plate above about 40 mm. Below that threshold it is optional, but buyers still specify the N condition for low-temperature impact duty, for cold-formed heads and wherever property uniformity across a large plate matters.

Q: What does the 70 in the grade name mean?
It is a strength class label derived from the 70 ksi minimum tensile level, corresponding to the 485–620 MPa tensile range. It is not a hardness value and it does not define a carbon content.

Q: Can SA516 Gr.70 be used at −30 °C?
Normalized plate with a specified Charpy requirement is routinely used at that temperature. The specification alone does not guarantee any impact value, so the test temperature and minimum absorbed energy must be written into the order and reported on the certificate.

Q: Is Q345R an acceptable substitute for SA516 Gr.70?
Q345R under GB/T 713 commonly meets or exceeds SA516 Gr.70 in strength and is tighter on phosphorus and sulphur, but it is a different specification with different design assumptions. Substitution requires documented engineering approval, not a certificate comparison alone.

Q: Does SA516 Gr.70 qualify for wet H2S sour service?
Not automatically. Sour duty requires tight sulphur and residual control, inclusion shape control and HIC or SSC qualification to stated acceptance criteria, all of which must be specified and tested rather than assumed from the base grade.

Send Inquiry

whatsapp

phone

Email

Inquiry