Nov 26, 2025 Leave a message

S235J2 Steel Plate: EN 10025-2 Composition and Mechanical Properties

S235J2 Steel Plate and Its Position in EN 10025-2

S235J2 is a non-alloy structural steel grade specified in EN 10025-2, the delivery standard for hot rolled products of structural steels in the non-alloy series. Its material number is 1.0117. The designation decodes in three parts: S for structural steel, 235 for a minimum yield strength of 235 MPa at thickness up to 16 mm, and J2 for Charpy V-notch impact testing at minus 20 °C with a minimum absorbed energy of 27 J. The grade is supplied mainly as plate and is used where a predictable, weldable steel is needed without alloy cost.

Chemical Composition of S235J2

Element EN 10025-2 requirement
C, max 0.17 % (thickness up to 40 mm)
Mn, max 1.40 %
P, max 0.025 %
S, max 0.025 %
N, max 0.009 %
Cu, max 0.55 %
CEV, max 0.35 % (thickness up to 40 mm)

The low carbon and the manganese cap keep the carbon equivalent low, which is what makes the J2 grade easy to weld without elaborate preheat. Phosphorus and sulfur are held at 0.025 % each, tighter than the JR and J0 variants of the same strength class, and nitrogen is controlled so that the aluminium-killed practice gives a fine grain size with dependable impact behaviour.

Mechanical Properties

Property Thickness range Value
Minimum yield strength, ReH up to 16 mm 235 MPa
Minimum yield strength, ReH 16 to 40 mm 225 MPa
Minimum yield strength, ReH 40 to 100 mm 215 MPa
Minimum yield strength, ReH 100 to 150 mm 195 MPa
Tensile strength, Rm up to 100 mm 360 to 510 MPa
Tensile strength, Rm 100 to 150 mm 350 to 500 MPa
Impact test, J2 all standard thicknesses 27 J minimum at minus 20 °C

Yield strength falls as thickness increases because the cooling rate through the section slows during rolling. Designers working with plate above 40 mm should therefore use the reduced ReH values rather than the nominal 235 MPa figure.

Delivery Condition and Tolerances

S235J2 plate is normally delivered hot rolled, with normalized (+N) supply available on request for heavy sections or where a more uniform structure is required. Dimensional tolerances for hot rolled plate follow EN 10029, which defines thickness, flatness and edge camber limits for plate 3 mm and above; the tolerance class should be named in the purchase order, because the same nominal thickness can be supplied against different tolerance bands. Plates are marked with the grade and heat number, and the marking must match the inspection document issued to EN 10204.

Fabrication, Welding and Forming

With a carbon equivalent limited to 0.35 %, S235J2 is welded by manual metal arc, MAG, submerged arc and resistance processes under standard procedures, and preheating is generally unnecessary for thicknesses below roughly 30 mm in normal workshop conditions. The grade bends and cold forms readily, is suitable for gas cutting and plasma cutting, and can be machined without difficulty. Where the plate is to be galvanized or painted, the controlled phosphorus and sulfur levels reduce the risk of surface defects that appear on poorer rimmed or semi-killed material.

Typical Applications

The grade is used for freight wagons, transmission towers, tipper bodies, cranes, trailers, excavators and other earth-moving structures, railway components, penstocks, pipes, highway bridge elements, general building structures, offshore support steelwork and storage tanks. Its combination of 27 J impact energy at minus 20 °C and low alloy cost makes it a common choice for outdoor structures in temperate and cold climates. The nearest Chinese equivalent in GB/T 700 is Q235D, but equivalence must be confirmed against the design specification before substitution.

Frequently Asked Questions

Q: What does the J2 suffix in S235J2 mean?
A: It is a Charpy V-notch impact requirement of 27 J minimum at a test temperature of minus 20 °C, which qualifies the steel for low-temperature structural service.

Q: What is the material number of S235J2?
A: 1.0117 in the EN 10025-2 non-alloy structural steel series.

Q: What is the yield strength of S235J2 plate?
A: 235 MPa minimum up to 16 mm, falling to 225 MPa at 16 to 40 mm, 215 MPa at 40 to 100 mm and 195 MPa at 100 to 150 mm.

Q: Is preheating required before welding S235J2?
A: Usually not for thin and medium plate, because the carbon equivalent is limited to 0.35 %. Heavy sections, high restraint joints and cold workshop conditions should still be assessed in the welding procedure.

Q: Does S235J2 need normalizing?
A: Not for ordinary use. Normalizing or normalizing rolling is ordered when uniform structure, better toughness or heavy thickness demands it.

Q: Can Q235D be used instead of S235J2?
A: They are close equivalents in strength and impact class, but substitution must be approved against the applicable design code and the inspection document requirements of the project.

Send Inquiry

whatsapp

phone

Email

Inquiry