Reading the SPV315 Data Set Correctly
SPV315 is a JIS G 3115 plate grade whose number denotes a minimum yield strength of 315 MPa, and whose practical data set is short: a chemistry table, a tensile table that changes with thickness, an impact requirement at a stated temperature, and a set of dimensional tolerances. Everything else that appears in a supplier brochure, including corrosion resistance and elevated temperature capability, follows from those four items rather than standing beside them. Buyers who compare grades on tensile strength alone routinely select a plate that fails the impact test on the vessel shop floor or that loses 20 MPa of yield during post-weld heat treatment.
The correct way to read the grade is to start from the design condition: the design temperature, the design pressure, the corrosion allowance, the welding process and the post-weld heat treatment cycle. Each of these converts into a specific requirement on the plate, and only then can a performance table be judged as adequate or inadequate. The sections below take the data in that order.
Chemical Composition and Its Effect on Properties
SPV315 is a carbon-manganese steel, not an alloy steel in the sense of chromium-molybdenum vessel grades. Carbon provides strength, manganese provides strength and controls sulphur, silicon deoxidises, and aluminium refines grain. There is no deliberate chromium addition to resist corrosion and no molybdenum addition to resist elevated temperature creep, so the grade is applied where the medium is not aggressive and the metal temperature stays in the intermediate range. The table gives the window that a plate mill normally holds, together with the property consequence of each element.
| Element | Typical content, % | Effect on measured properties |
|---|---|---|
| C | 0.13-0.16 | Raises yield and tensile strength; each 0.01% costs roughly 3-5 J of Charpy energy near the transition |
| Mn | 0.90-1.40 | Strengthens solid solution and combines with sulphur; raises hardenability of the weld heat-affected zone |
| Si | 0.15-0.35 | Deoxidation; above 0.35% the weld heat-affected zone toughness deteriorates |
| P | 0.020 max | Segregates to grain boundaries; raises transition temperature and promotes temper embrittlement |
| S | 0.008 max in good practice | Forms manganese sulphide stringers; lowers through-thickness ductility and upper-shelf energy |
| Al soluble | 0.020-0.045 | Grain refinement; below 0.015% the impact requirement becomes difficult to hold in thick plate |
| Cu, Sn, As | Residual, mill-controlled | Each raises the transition temperature; the sum matters more than any single element |
Carbon equivalent, calculated with the conventional formula that weights manganese, chromium, molybdenum, vanadium, nickel and copper against carbon, sits near 0.36-0.40 for this grade. That figure is not a property of the steel in service but a fabrication instruction: it sets the preheat temperature, the maximum heat input and the need for hydrogen-controlled consumables. A plate at the top of the carbon range welded without preheat in a cold shop is a cracking risk regardless of how good its certificate looks.
Tensile and Yield Properties Across Thickness
Yield and tensile strength are specified as minima, with a tensile range whose upper limit prevents the mill from over-strengthening the steel at the expense of toughness. Elongation limits fall as thickness rises because the gauge length covers a larger volume of material with more inclusion content and less through-thickness deformation. A buyer comparing two offers should always ask at which thickness the reported values were obtained; a 12 mm plate and a 90 mm plate of the same grade do not deliver the same elongation.
| Property | Thin plate, 6-16 mm | Medium plate, 16-40 mm | Heavy plate, 40-100 mm |
|---|---|---|---|
| Yield strength, min | 315 MPa | 315 MPa | 315 MPa, verified after stress relief |
| Tensile strength, typical range | 520-640 MPa | 520-640 MPa | 520-640 MPa, narrower in practice |
| Elongation, min, 50 mm gauge | 21% and above | 19-21% | 17-19% |
| Charpy test temperature | 0 °C typical | 0 °C typical | 0 °C, or lower by agreement |
| Charpy average energy, min | 31 J | 31 J | 31 J, single value not below 70% of average |
The practical consequence is that a heavy plate order needs a wider margin between the specified minimum and the mill's aim strength, because the same heat rolled to 80 mm will test at a lower yield after normalising and stress relieving than the 12 mm plate from the same slab. Orders that fix a minimum yield of 315 MPa at 80 mm with a full simulated post-weld heat treatment are achievable, but the mill must aim above the minimum at the ladle and hold carbon and manganese toward the upper half of the window.
Impact Toughness and Transition Behaviour
Charpy absorbed energy is the property that separates a compliant plate from a rejected one, because it is the property most sensitive to process drift. Test temperature is specified on the order, most commonly at 0 °C for this grade, and the result is reported as the average of three specimens taken transverse to the rolling direction together with the lowest individual value. Transverse specimens are used because the plate's weakest direction is across the rolling direction, where inclusions and banding lie.
The transition from ductile to brittle behaviour is not a single number. A plate that gives 60 J at 0 °C may give 25 J at minus 20 °C, and the spread within a single plate between the top and bottom end can be 15-20 J. Where the design temperature is below the standard test temperature, the purchaser must specify a lower impact test temperature and accept the thicker, more heavily normalised plate that follows; asking a mill to guarantee a sub-zero requirement on a standard SPV315 rolling schedule without changing the chemistry or the normalising practice is the usual source of late rejection.
Elevated Temperature Strength and Design Allowables
SPV315 is intended for intermediate temperature service, and its strength at temperature is the reason the grade exists in the SPV series. Above roughly 350 °C plain carbon-manganese steel begins to lose yield strength steadily, and above roughly 400 °C creep deformation becomes the governing design consideration rather than short-term tensile strength. Design codes therefore publish allowable stress values that decline with temperature, and the designer selects the lower of the allowable based on yield, the allowable based on tensile strength and, above the creep threshold, the creep-limited allowable.
The practical limit for this grade in continuous service is commonly taken as around 400 °C, with chromium-molybdenum grades taking over where the metal temperature is higher. Buyers should not infer that a plate acceptable at 350 °C is acceptable at 450 °C because the room-temperature tensile result has margin; the relevant data are the code allowable stresses at the design temperature, and these must be taken from the edition of the design code that governs the vessel.
Corrosion Behaviour in Service Media
The corrosion resistance of SPV315 comes from its carbon-manganese composition alone; there is no chromium-rich passive film and no alloy addition that resists an aggressive medium. In dry, non-corrosive service such as compressed air, nitrogen or dry hydrocarbon, corrosion is negligible and the design corrosion allowance can be small. In wet hydrocarbon, sour water, dilute acid or chloride-bearing service, the plate behaves like ordinary carbon steel: it corrodes uniformly at a rate set by the medium, temperature and flow, and it is susceptible to pitting under deposits.
For that reason vessel design normally includes a corrosion allowance of 1.5 to 3 mm, deducted from the calculated thickness, and the plate specification should require that the ordered thickness be the design thickness plus allowance plus any forming allowance. Where the medium is aggressive, the correct response is a stainless cladding, a lining or a change of grade, not a thicker SPV315 plate. Suppliers that describe this grade as having a dense oxide film that resists chemical attack are describing a different class of material.
Welding, Forming and the Effect on Properties
SPV315 welds readily with the shielded metal arc, submerged arc, gas metal arc and flux-cored processes using carbon-manganese consumables matched to the plate strength. Preheat is required in proportion to carbon equivalent and thickness; a common rule for this grade is ambient preheat for thin plate in warm conditions and 100-150 °C for thicker sections or low ambient temperature, with interpass temperature controlled so that the heat-affected zone does not become coarse. Heat input should stay within the range qualified by the welding procedure, because excessive heat input coarsens the heat-affected zone and lowers its toughness below the plate value.
Cold forming is straightforward up to moderate radii, with the bend axis preferably transverse to the rolling direction and the bend radius generous enough to avoid surface cracking on the outside of the bend. After forming and welding, the vessel is normally given a post-weld heat treatment at a temperature below the lower critical range, which relieves residual stress but slightly reduces yield and tensile strength. Test coupons that are intended to represent the finished vessel must therefore receive the same simulated heat treatment before testing; a certificate based on as-normalised plate understates the risk.
Property Anisotropy, Thickness Effects and Test Location
Rolled plate is not isotropic. Longitudinal specimens typically show 10-20 MPa higher yield and 10-20 J higher Charpy energy than transverse specimens, because inclusions and microstructural banding align with the rolling direction. Through-thickness ductility is the lowest of all and is the property that governs resistance to lamellar tearing in tee joints and nozzle welds; where the fabrication includes highly restrained joints, the order should specify a through-thickness tensile test or an inclusion content limit rather than rely on in-plane results.
Test location also matters. Coupons taken near the plate ends, which experience less total reduction and different cooling, can differ from mid-length coupons. Specifying that tests be taken at a defined position relative to the plate end and the rolling direction makes results comparable between suppliers, and it is one of the few specification clauses that costs nothing to add but prevents most disputes about marginal results.
Comparing Certificates and Offer Sheets
A usable offer for SPV315 states the grade, the standard, the delivery condition, the thickness range and the impact test temperature. A certificate that lists chemistry without the corresponding mechanical results, or that reports only typical values rather than heat-specific values, cannot support a pressure-vessel file. The buyer should check that the heat number on the certificate matches the plate marking, that the tensile and impact results correspond to the delivery condition actually supplied, and that the dimensions fall within the tolerances of the applicable dimensional standard for plate.
Where two offers differ substantially in strength at the same nominal grade, the explanation is usually not fraud but a difference in the aim chemistry and in whether the plate was normalised after rolling. That difference is legitimate only if it is declared, because it changes the welding procedure, the design allowable and the impact behaviour of the finished vessel.
FAQ
Q: What is the minimum yield strength of SPV315 plate?
The grade designation sets a minimum yield strength of 315 MPa, with a tensile strength typically in the range of 520 to 640 MPa and minimum elongation that reduces as plate thickness increases.
Q: At what temperature is SPV315 impact tested?
Impact testing at 0 °C is the common basis, reported as the average of three transverse specimens with a minimum average absorbed energy of about 31 J and a limit on the lowest individual result; a lower test temperature must be specified on the order.
Q: Is SPV315 corrosion resistant?
It is a plain carbon-manganese steel with no chromium addition, so it corrodes like ordinary carbon steel in aggressive media and is normally protected by a design corrosion allowance, a lining or cladding rather than by the plate itself.
Q: Up to what temperature can SPV315 be used?
Continuous service is commonly limited to about 400 °C, and the governing design value is the allowable stress at the design temperature taken from the applicable vessel code rather than the room-temperature tensile result.
Q: How does post-weld heat treatment change the properties?
Stress relief below the lower critical temperature reduces residual stress and lowers yield and tensile strength slightly, so acceptance tests should be carried out on coupons given the same simulated heat treatment as the finished vessel.
Q: Why do transverse properties matter more than longitudinal?
Inclusions and banding align with the rolling direction, so transverse specimens show lower ductility and toughness and represent the weakest plane of the plate, which is why specifications test in that direction.




