Jan 28, 2026 Leave a message

What are the specific chemical composition requirements for C in ASME SA 516 Grade 65?

What are the specific chemical composition requirements for C in ASME SA 516 Grade 65 ?

The chemical composition requirements for Carbon (C) in ASME SA 516 Grade 65 vary based on plate thickness, with a maximum limit ranging from 0.24% to 0.29% for heat analysis. Generally, for thicknesse≤1/2in. (12.5 mm), the max C is 0.24% , increasing up to 0.29% for thicknesses over 4 in (100 mm).

ASME SA 516 Grade 65

ASME SA516 Grade 65 is a medium-strength carbon steel plate specifically intended for use in welded pressure vessels where improved notch toughness is important. It belongs to the PVQ (Pressure Vessel Quality) family of steels, which means it undergoes more rigorous testing and quality control than standard structural steel. It is produced as "killed steel," usually silicon-killed, and is manufactured to a fine-grain practice. This ensures the material remains stable and resistant to brittle failure, particularly in applications where the vessel might be exposed to ambient temperatures lower than typical carbon steel limits.

 

Key Characteristics

Balanced Ductility: Offers a superior elongation profile compared to Grade 70, allowing for safer energy absorption.

Homogeneity: High internal cleanliness and uniform grain structure due to the "killed" manufacturing process.

Thermal Stability: Maintains its mechanical properties effectively during the moderate heat cycles involved in fabrication.

Predictable Hardness: Typically displays a very consistent Brinell hardness across the plate surface.

 

Grade Designation

"SA": The prefix "S" stands for "Section II" (Materials), and "A" denotes a ferrous metal (iron-based). This indicates the material is approved for use in ASME-stamped pressure vessels.

"516": This identifies the specific specification for "Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service."

"Grade 65": This represents the Minimum Tensile Strength of the steel, which is 65 ksi (65,000 pounds per square inch).

 

Comparison SA516 Gr. 65 vs. SA516 Gr. 60 

Weight Reduction: Grade 65 provides roughly an 8% increase in minimum tensile strength over Grade 60. This allows engineers to specify thinner wall sections, leading to significant weight savings in large-scale storage spheres.

Weld Volume: By utilizing the higher allowable stress of Grade 65, the total volume of weld metal required for a vessel decreases as the plate thickness is reduced, lowering overall fabrication time and cost.

Market Availability: Grade 65 is often easier to source globally than Grade 60, as many mills stock "dual-certified" Grade 65/70 plates that can satisfy Grade 60 requirements but not vice versa.

Pressure Rating: For the same thickness, a vessel made of Grade 65 can be rated for a higher Maximum Allowable Working Pressure (MAWP) than one made of Grade 60.

info-739-194

Common Applications

Petrochemical Reactors: Used for the outer shells of reactors where moderate pressures are constant.

Compressed Air Tanks: Found in large-scale industrial air receivers.

Filter Housings: Heavy-duty liquid and gas filtration systems in municipal water or oil plants.

Manifold Systems: Used in high-pressure piping manifolds where plate-to-pipe welding is required.

 

What is the impact test requirement for ASME SA516 Grade 65?

ASME SA516 Grade 65 is typically tested for impact toughness at temperatures of 0°F (-18°C). This test ensures the material can withstand low-temperature stresses and avoid brittle fracture. The impact test requires the material to absorb a minimum energy value of 20 ft-lbs (27 J) at the specified temperature, ensuring it is tough enough for its intended high-pressure applications.

What are the benefits of using ASME SA516 Grade 65?

The key benefits of using ASME SA516 Grade 65 include its excellent weldability, high tensile strength, and resistance to thermal degradation. It is an ideal material for pressure vessels and boilers, especially in industries such as power generation, oil, and chemical processing. The material's ability to withstand high pressures and temperatures makes it a safe and reliable choice for these demanding applications.

What welding methods are suitable for ASME SA516 Grade 65?

ASME SA516 Grade 65 can be welded using various techniques, including Shielded Metal Arc Welding (SMAW), Gas Tungsten Arc Welding (GTAW), and Gas Metal Arc Welding (GMAW). For thicker sections, preheating is often recommended to reduce the risk of thermal cracking. Post-weld heat treatment (PWHT) can be used to relieve stresses and enhance the material's mechanical properties after welding.

 

Mechanical Properties

Grade

Yield strength
(min ksi)

Tensile strength
(ksi)

Elongation in 2" 1)
(min %)

Elongation in 8" 1)
(min %)

65

35

65 - 85

23

19

 

Chemical Composition

C
(%)

Mn 1)
(%)

P 2)
(%)

S 2)
(%)

Si
(%)

0.24

0.85 - 1.20

0.020

0.010

0.15 - 0.40

 

1. What is the sulfur content in ASME SA516 Grade 65?

The sulfur content in ASME SA516 Grade 65 is limited to a maximum of 0.035%. This low sulfur content is essential for preventing the formation of sulfide inclusions, which can weaken the material and make it more susceptible to cracking, especially during welding. The low sulfur content ensures better weldability and improves the overall toughness of the material.

 

2. What is the tensile strength of ASME SA516 Grade 65?

The tensile strength of ASME SA516 Grade 65 ranges from 65 ksi to 85 ksi (448–586 MPa). This tensile strength allows the material to maintain structural integrity in pressure vessels, boilers, and heat exchangers, even under extreme pressure and high-temperature conditions. The material's strength is one of its key features for safety in high-stress industrial environments.

 

3. What is the phosphorus content in ASME SA516 Grade 65?

The phosphorus content in ASME SA516 Grade 65 is limited to a maximum of 0.035%. This limitation is important because excessive phosphorus can make the material brittle and prone to cracking, especially in low-temperature environments. By controlling phosphorus content, the steel retains its strength and toughness, making it suitable for high-pressure and high-temperature applications.

 

4. What is the maximum thickness for ASME SA516 Grade 65?

The maximum thickness for ASME SA516 Grade 65 plates is generally 4 inches (102 mm) for pressure vessel and boiler applications. Plates above this thickness may require additional considerations, such as post-weld heat treatment, to ensure the desired mechanical properties are achieved. The thickness determines the steel's ability to handle internal pressure and its overall structural integrity.

 

5. Can ASME SA516 Grade 65 be welded?

Yes, ASME SA516 Grade 65 is known for its good weldability. It can be welded using common welding techniques such as SMAW (Shielded Metal Arc Welding), GMAW (Gas Metal Arc Welding), and GTAW (Gas Tungsten Arc Welding). Preheating and post-weld heat treatment (PWHT) are often recommended for thicker sections to reduce the risk of cracking and to maintain the material's integrity.

 

6. What is the elongation of ASME SA516 Grade 65?

For plates with a thickness of up to 1.5 inches (38 mm), ASME SA516 Grade 65 typically has an elongation of 20% in 8 inches (200 mm). This high elongation value indicates the material's good ductility, allowing it to stretch without breaking under tension, which is crucial for applications involving high stress, such as pressure vessels.

 

7. What is the chemical composition of ASME SA516 Grade 65?

The chemical composition of ASME SA516 Grade 65 typically includes:,Carbon (C): 0.18–0.23%,Manganese (Mn): 0.60–1.35%,Phosphorus (P): ≤0.035%,Sulfur (S): ≤0.035%,Silicon (Si): 0.15–0.40%,These elements help provide the material with its strength, toughness, and resistance to thermal degradation under high temperatures, making it suitable for pressure vessel applications.

 

 

 

Contact now

Contact us at info@gneesteels.com for pricing, technical support, or customized solutions. We are always ready to support your project

info-554-562

Send Inquiry

whatsapp

phone

Email

Inquiry