What is the typical Yield Strength for ASME SA 516 Grade 65?
The minimum yield strength for ASME SA 516 Grade 65 pressure vessel steel is 35 ksi (240 MPa or 241 MPa in some standards). This material is characterized by a tensile strength range of 65-85 ksi ( 450−585 MPa ), designed for intermediate-temperature service.

ASME SA516 Grade 65 serves as a high-integrity carbon steel solution for manufacturers building boilers and pressure containment systems. It occupies a technical niche between the lower-strength Grade 60 and the high-strength Grade 70. By providing a minimum tensile strength of 65,000 psi, it allows designers to optimize wall thickness while retaining the ease of welding and forming associated with lower-carbon steels. It is the material of choice when a project requires more "toughness headroom" than standard carbon steel but doesn't require the extreme strength of Grade 70.
Key Characteristics
Notch Toughness Focus: Highly resistant to the propagation of cracks under impact loads.
Clean Steel Chemistry: Low levels of Phosphorus and Sulfur prevent "hot shortness" during welding.
Standardized Heat Treatment: Responds exceptionally well to normalizing, which refines the grain and enhances low-temp performance.
Consistent Machinability: Easier to drill and bevel compared to higher carbon equivalents.
Grade Designation
"SA": The prefix "S" stands for "Section II" (Materials), and "A" denotes a ferrous metal (iron-based). This indicates the material is approved for use in ASME-stamped pressure vessels.
"516": This identifies the specific specification for "Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service."
"Grade 65": This represents the Minimum Tensile Strength of the steel, which is 65 ksi (65,000 pounds per square inch).
Comparison SA516 Gr. 65 vs. EN 10028-3 P355NH
Yield-to-Tensile Ratio: The European grade P355NH typically features a higher yield strength (approx. 355 MPa ) compared to the 240 MPa of SA516 Gr. 65, meaning the European standard is more optimized for yield-based design.
Grain Size Control: EN 10028-3 mandates specific Aluminum content to guarantee a fine-grain structure, whereas SA516 Gr. 65 requires the "Fine Grain Practice" to be explicitly invoked via supplementary requirements or as part of the standard killed-steel process.
Chemical Purity: European standards often have tighter limits on trace elements like Copper and Tin, while SA516 Gr. 65 relies on the "Killed Steel" designation to ensure internal cleanliness and resistance to aging.
Testing Protocols: P355NH requires mandatory impact testing at specific temperatures, while SA516 Gr. 65 testing is governed by the ASME Section VIII MDMT (Minimum Design Metal Temperature) curves.

Common Applications
Spherical Storage Tanks: Specifically for "Horton Spheres" storing butane or propane.
Boiler Steam Drums: High-temperature steam containment in industrial power plants.
Waste Heat Recovery Units (WHRU): Used in the shells of heat recovery systems.
LNG Pre-treatment Vessels: Components used in the initial stages of gas processing before cryogenic cooling.
What are the inspection requirements for ASME SA516 Grade 65?
The inspection requirements for ASME SA516 Grade 65 typically include visual inspection, ultrasonic testing (UT), and sometimes magnetic particle or dye penetrant testing for surface defects. Mechanical tests such as tensile, impact, and hardness tests are also carried out to ensure the material meets the specified strength and toughness requirements. Inspection and certification are essential for ensuring the material is suitable for use in pressure vessels and other critical applications.
What is the maximum thickness for ASME SA516 Grade 65?
The maximum thickness for ASME SA516 Grade 65 plates is generally 4 inches (102 mm) for pressure vessel and boiler applications. Plates above this thickness may require additional considerations, such as post-weld heat treatment, to ensure the desired mechanical properties are achieved. The thickness determines the steel's ability to handle internal pressure and its overall structural integrity.
Can ASME SA516 Grade 65 be used for cryogenic applications?
No, ASME SA516 Grade 65 is not suitable for cryogenic applications. Its impact toughness and low-temperature properties are not designed for extremely cold environments, like those found in liquefied natural gas (LNG) tanks or cryogenic storage systems. Materials with higher toughness and low-temperature resistance, such as SA516 Grade 70 or other specialized low-temperature steels, would be more appropriate.
| Elements | SA 516 Gr 65 (Grade 450) |
|---|---|
| Carbon, max Composition % | |
| 1/2 in. (12.5 mm) and under | 0.24 |
| Over 1/2 to 2 in. (12.5 to 50 mm), incl | 0.26 |
| Over 2 to 4 in. (50 to 100 mm), incl | 0.28 |
| Over 4 to 8 in. (100 to 200 mm), incl | 0.29 |
| Over 8 in. (200 mm) | 0.29 |
| Manganese, max | |
| 1/2 (12.5) and under: | |
| Heat analysis | 0.85-1.20 |
| Product analysis | 0.79-1.30 |
| Over 1/2 in (12.5) | |
| Heat analysis | 0.85-1.20 |
| Product analysis | 0.79-1.30 |
| Phosphorus, max | 0.025 |
| Sulfur, max | 0.025 |
| Silicon | |
| Heat analysis | 0.15-0.40 |
| Product analysis | 0.13-0.45 |
Tensile Requirements
| SA 516 Gr 65 (Grade 450) |
|
|---|---|
| Tensile strength, ksi (MPa) | 65-85(450-585) |
| Yield strength, min.B ksi (MPa) | 35(240) |
| Elongation in 8 in. (200 mm), min, % | 19 |
| Elongation in 2 in. (50 mm), min, % | 23 |
1. What is ASME SA516 Grade 65?
ASME SA516 Grade 65 is a carbon steel grade designed for use in the fabrication of pressure vessels and boilers that operate under high-pressure and high-temperature conditions. It is part of the ASME Boiler and Pressure Vessel Code (BPVC). Known for its good weldability, it is often used in the construction of pressure vessels in industries such as power generation and chemical processing.
2. What is the tensile strength of ASME SA516 Grade 65?
The tensile strength of ASME SA516 Grade 65 ranges from 65 ksi to 85 ksi (448–586 MPa). This tensile strength allows the material to maintain structural integrity in pressure vessels, boilers, and heat exchangers, even under extreme pressure and high-temperature conditions. The material's strength is one of its key features for safety in high-stress industrial environments.
3. What are the corrosion resistance properties of ASME SA516 Grade 65?
While ASME SA516 Grade 65 has moderate corrosion resistance, it is not designed to withstand highly corrosive environments. It performs well in environments where corrosion is not a major concern, but for applications exposed to harsh chemicals, acids, or saltwater, additional protective coatings or corrosion-resistant alloys may be needed. For such conditions, stainless steels or corrosion-resistant materials may be more suitable.
4. What is the sulfur content in ASME SA516 Grade 65?
The sulfur content in ASME SA516 Grade 65 is limited to a maximum of 0.035%. This low sulfur content is essential for preventing the formation of sulfide inclusions, which can weaken the material and make it more susceptible to cracking, especially during welding. The low sulfur content ensures better weldability and improves the overall toughness of the material.
5. What are the mechanical properties of ASME SA516 Grade 65?
The mechanical properties of ASME SA516 Grade 65 include:
Tensile Strength: 65-85 ksi (448–586 MPa)
Yield Strength: 38 ksi (260 MPa) minimum
Elongation: 20% (for plates with thickness ≤ 1.5 inches)
These properties indicate its good tensile strength, ductility, and ability to withstand considerable stress and strain, particularly in high-temperature environments.
6. What is the chemical composition of ASME SA516 Grade 65?
The chemical composition of ASME SA516 Grade 65 typically includes:,Carbon (C): 0.18–0.23%,Manganese (Mn): 0.60–1.35%,Phosphorus (P): ≤0.035%,Sulfur (S): ≤0.035%,Silicon (Si): 0.15–0.40%,These elements help provide the material with its strength, toughness, and resistance to thermal degradation under high temperatures, making it suitable for pressure vessel applications.
7. What is the yield strength of ASME SA516 Grade 65?
The yield strength of ASME SA516 Grade 65 is typically 38 ksi (260 MPa) at room temperature. This ensures the material can handle internal pressures from gas or liquid contents without deforming or yielding. Its yield strength makes it suitable for pressure vessel and boiler applications, where the material must withstand high internal pressure without failure.
For more details about GNEE's steel products, contact us at info@gneesteels.com. We look forward to working with you.





