What is ASME SA 285 Grade C equivalent to?
ASME SA 285 Grade C is a low-carbon, high-tensile strength steel plate typically used for pressure vessels and boilers, featuring a tensile strength of 55–75 ksi (380–515 MPa). Its primary equivalent is ASTM A285 Grade C, with other major international equivalents including European P235GH (EN 10028-2), German DIN 17155 HI, Japanese JIS G3115 SPV235, and Chinese GB 713 Q245R.

ASME SA285 Grade C is a standard carbon steel specification for pressure vessel plates with low-to-intermediate tensile strength. It is specifically designed for fusion-welded pressure vessels where high strength is less critical than weldability and ease of fabrication. Unlike many modern high-performance steels, SA285 Grade C is often produced as semi-killed or killed steel and is strictly limited to a maximum thickness of 2 inches (50 mm) to ensure a uniform internal structure. This makes it a cost-effective, "workhorse" material for stationary storage tanks and low-pressure boilers where moderate mechanical properties are sufficient to meet safety requirements.
Key Characteristics
Superior Weldability: Its low carbon content makes it exceptionally easy to weld without specialized preheating.
Formability: Highly ductile, allowing it to be cold-rolled or bent into vessel shells with ease.
Economic Efficiency: One of the most affordable pressure vessel grades due to simple alloying and manufacturing.
Thickness Cap: Restricted to 2 inches (50 mm) to maintain structural reliability in its non-killed or semi-killed state.
Grade Designation
Standard ID: ASME SA285.
Specific Level: Grade C.
Material Group: Low-to-Intermediate Tensile Strength Carbon Steel.
Comparison with ASME SA516 Grade 70
Strength Levels: SA285 Grade C is significantly weaker (55–75 ksi tensile) compared to SA516-70 (70–90 ksi).
Internal Soundness: SA516 is always a "killed" steel (fully deoxidized), whereas SA285 is often semi-killed.
Thickness Limits: SA516 can be produced in very heavy plates (up to 8 inches), while SA285 is strictly capped at 2 inches.
Common Applications
Storage Tanks: Large-scale atmospheric tanks for water or non-corrosive chemicals.
Low-Pressure Boilers: Heating units for residential or light industrial use.
Ductwork: Large-diameter pressurized piping for air or gas distribution.

What is the tensile strength of SA285 Grade C?
SA285 Grade C has a tensile strength of about 415 MPa. This tensile strength is moderate and suitable for applications where the material is subjected to low- to medium-stress environments. It offers good strength without being overly hard, ensuring that it remains ductile enough for pressure vessel applications while providing adequate strength for the structural integrity of components under normal operating conditions.
What are the main applications of SA285 Grade C?
SA285 Grade C is commonly used in the construction of pressure vessels, heat exchangers, and other types of industrial equipment. Its low carbon content gives it good weldability, which makes it easy to fabricate and join. It is typically used in applications where the steel is exposed to low or moderate pressure and temperature conditions, such as in steam boilers and chemical plants.
What is the elongation of SA285 Grade C?
SA285 Grade C typically has an elongation of 22% at a gauge length of 8 inches. This elongation value indicates that the material has good ductility and can deform significantly before failure. This property makes SA285 Grade C suitable for applications that require moderate bending or forming, such as in pressure vessels, where the material needs to stretch or bend without fracturing under low-pressure conditions.
Chemical Requirements
| Element Composition % | SA 285 Gr C |
|---|---|
| Carbon, max | 0.28 |
| Manganese, max | |
| Heat analysis | 0.90 |
| Product analysis | 0.98 |
| Phosphorus, max | 0.025 |
| Sulfur, max | 0.025 |
Tensile Requirements
| SA 285 Gr C ksi (MPa) |
|
|---|---|
| Tensile strength | 55-75 (380-515) |
| Yield strength, min | 30 (205) |
| Elongation in 8Â in. or (200Â mm), min, % | 23 |
| Elongation in 2Â in. or (50Â mm), min, % | 27 |
1What is ASME SA285 Grade C?
ASME SA285 Grade C is a carbon steel used primarily in the fabrication of pressure vessels, heat exchangers, and boilers. It has good weldability, making it ideal for use in lower-pressure systems. Grade C offers moderate tensile strength and is commonly used in the manufacturing of vessels that operate at relatively low pressure and temperature conditions, typically below 300°F (150°C).
2What are the chemical composition of ASME SA285 Grade C?
ASME SA285 Grade C consists of primarily carbon (0.23–0.28%), manganese (0.60–0.90%), silicon (0.13–0.45%), and sulfur (0.035% max). The alloy also includes trace amounts of phosphorus and other elements that enhance its overall properties. This composition allows the steel to possess good weldability and moderate strength, making it suitable for applications in pressure vessels and boilers operating under moderate conditions.
3What is the yield strength of SA285 Grade C?
The yield strength of ASME SA285 Grade C is approximately 205 MPa. This relatively low yield strength makes it suitable for use in applications that involve low pressure and temperature. Its yield strength ensures that it performs reliably in conditions where stresses are moderate, providing a balance between strength and ductility for ease of fabrication and serviceability in pressure vessel construction.
4What is the cost of SA285 Grade C?
The cost of SA285 Grade C is generally lower than that of higher-strength alloys due to its relatively simple carbon-steel composition. However, the cost can vary based on market demand, production methods, and supply chain conditions. Compared to high-alloy steels or other more advanced materials like SA516 Grade 70, SA285 Grade C remains an economical choice for applications requiring moderate strength and corrosion resistance.
5What is the welding process for SA285 Grade C?
SA285 Grade C has good weldability, which makes it ideal for welding in the construction of pressure vessels and other equipment. However, preheating may be required before welding to prevent cracking, especially for thicker sections. Low-hydrogen electrodes are recommended to avoid hydrogen-induced cracking, and post-weld heat treatment may be needed to relieve residual stresses, improving the material's overall strength and ductility.
6What is the mechanical properties of SA285 Grade C?
SA285 Grade C has a yield strength of approximately 205 MPa and a tensile strength of 415 MPa. It exhibits good elongation, typically 22% at a gauge length of 8 inches, allowing for a reasonable amount of deformation before failure. The material's moderate strength and high ductility make it suitable for pressure vessel applications where low- to moderate-stress conditions are encountered
7How does SA285 Grade C perform in low-temperature environments?
SA285 Grade C is not ideal for low-temperature environments. Its mechanical properties are designed for moderate temperatures, and at lower temperatures, the steel may become brittle and prone to cracking. For applications where low temperatures are a concern, materials specifically designed for cryogenic or low-temperature environments, such as SA537 or other low-alloy steels, are preferred to maintain structural integrity and toughness.
Full specification and details are available on request. The above information is provided for guidance purposes only. For specific design requirements please contact our technical sales staff





