Aug 21, 2025 Leave a message

S890Q S890QL S890QL1 steel plates.pdf

S890Q High Strength Plate: Grade Selection and Fabrication

What S890Q Is and Where It Sits in the 890 MPa Family

S890Q is the base grade of the three 890 MPa quenched and tempered structural steels listed in EN 10025-6. The number is the minimum yield strength in megapascals for plate from 3 mm to 50 mm thick, and the Q confirms that the plate is delivered in the quenched and tempered condition. It is a low alloy steel, not a tool steel and not a wear plate: its alloy design exists to make a 890 MPa yield strength achievable in a weldable section, and its carbon content is deliberately kept low so that the weld heat affected zone remains tough.

The distinction that matters commercially is that S890Q carries no low temperature impact guarantee beyond the room temperature and minus 20 degrees C testing associated with the Q class, while the L and L1 variants extend the verified Charpy energy down to -40 and -60 degrees C. Many buyers default to the L grade on every enquiry, which is unnecessary cost when the structure will never see sub-zero metal temperature. Understanding when the base grade is the correct and economical answer is a core purchasing skill for high strength plate.

S890Q is also the grade most often used in thin and medium gauges for mobile equipment, where the aim is to remove weight from a boom, arm or frame while keeping the section stable under compression. In those gauges the quench is fast across the full section, so a lean alloy addition is enough to reach the strength level, and the plate remains readily cut, drilled and bent with conventional workshop equipment.

Chemistry: A Low Carbon, Microalloyed Balance

The specified maximum analysis for S890Q is 0.20% carbon, 0.80% silicon, 1.70% manganese, 0.025% phosphorus, 0.015% sulphur, 0.015% nitrogen, 0.005% boron, 1.50% chromium, 0.50% copper, 0.70% molybdenum, 0.06% niobium, 2.00% nickel, 0.05% titanium, 0.12% vanadium and 0.15% zirconium, with a maximum carbon equivalent of 0.82. All of these are ceilings, and a well controlled heat sits well inside most of them.

The metallurgical logic is straightforward. Carbon provides the strength after quenching but also drives hardness, cold cracking and loss of toughness, so it is limited and the strength is instead obtained from the martensitic transformation plus tempering. Manganese, chromium, molybdenum and boron supply hardenability, ensuring that the core of the plate transforms rather than forming ferrite and pearlite bands that would destroy both strength and uniformity. Nickel raises toughness, particularly at low temperature, and is the element a mill adds when a heavy gauge order is difficult to meet. Niobium, vanadium and titanium act as grain refiners and precipitation strengtheners: they keep the austenite grain size fine during the austenitizing soak and then form fine carbides and nitrides that contribute to the tempered strength. Titanium additionally protects the boron addition by combining with nitrogen before boron can, which is why boron without titanium protection is ineffective.

For the fabricator the practical reading of this chemistry is the carbon equivalent. Two S890Q heats at 0.65 and 0.81 CEV both pass the standard but behave very differently under the arc: the leaner heat tolerates lower preheat and faster cooling, while the richer heat needs a disciplined thermal cycle to avoid hydrogen cracking in thick joints. Requesting the heat analysis with the quotation is a low cost habit that prevents weld procedure rework later.

Mechanical Property Requirements and How to Read Them

The guaranteed values step down with thickness because the cooling rate at the centre of a heavy plate is slower, so less martensite forms and the tempering response changes. The following table summarises the requirements a mill certificate should demonstrate for the 890 MPa quenched and tempered family, including the impact class distinction that defines each suffix.

Requirement S890Q S890QL S890QL1
Minimum yield strength, 3 to 50 mm 890 MPa 890 MPa 890 MPa
Minimum yield strength, over 50 to 100 mm 830 MPa 830 MPa 830 MPa
Tensile strength, 3 to 50 mm 940 to 1100 MPa 940 to 1100 MPa 940 to 1100 MPa
Tensile strength, over 50 to 100 mm 880 to 1100 MPa 880 to 1100 MPa 880 to 1100 MPa
Minimum elongation A 11% 11% 11%
Charpy impact, lowest specified test temperature 0 degrees C, 50 J -40 degrees C, 30 J -60 degrees C, 27 J
Maximum carbon equivalent 0.82 0.82 0.82
Typical delivery condition Quenched and tempered Quenched and tempered Quenched and tempered

Three details in that table are frequently misread. The tensile range has an upper bound, so a heat that tests at 1130 MPa is non-conforming even though the number looks impressive. Elongation is a minimum on a proportional gauge length, and it falls as strength rises, so a 11% result is normal for this grade and does not indicate a defective plate. Impact energy is an average of three specimens with a permitted single low value above a specified floor, and the test temperature and specimen orientation must both appear on the certificate; a 50 J result quoted without the temperature is not evidence of anything.

Choosing Between Q, L and L1 on a Real Project

The selection rule is driven by the lowest metal temperature the structure can experience, not by the ambient air temperature on a typical working day. Consider cold soak during winter transport, shutdown periods in unheated plants, refrigerated or high altitude service, and the cooling effect of wind on an exposed steel member. As a working rule, if the minimum metal temperature stays above -20 degrees C the base Q grade with verified impact testing is appropriate, between -20 and -40 degrees C the L grade is required, and below -40 degrees C the L1 grade is the only correct choice.

Do not assume that upgrading the strength grade compensates for a lower toughness class. A S960Q plate is stronger than S890Q but is not tougher at low temperature, and substituting a higher strength steel into a cold climate application can reduce the safety margin rather than increase it. Conversely, paying for S890QL in an indoor machine frame at 25 degrees C adds cost and can narrow the supply base without adding real integrity.

A second selection axis is thickness. As plate moves beyond 50 mm the guaranteed yield drops to 830 MPa and the quench becomes more demanding, so the supplier list narrows and ultrasonic testing becomes a routine requirement rather than an optional extra. If a design can be realised at 45 mm rather than 55 mm, it often gains strength, availability and price at the same time.

Heat Treatment: The Step That Creates the Grade

The mechanical properties of S890Q are made on the heat treatment line, not in the rolling mill alone. After controlled rolling, the plate is austenitized in a continuous furnace at a temperature high enough to dissolve the alloy carbides but low enough to avoid grain coarsening; a typical window sits in the region of 900 to 930 degrees C, held long enough for the section to reach temperature uniformly, roughly one minute per millimetre of thickness in many practices. The plate is then quenched, usually in a roller pressure quencher that delivers high flow water to both surfaces to keep the cooling rate above the critical value through the thickness.

Tempering follows immediately, in the range that produces the required strength while restoring toughness, commonly between 550 and 650 degrees C depending on the analysis and the gauge. This is the step where the mill trades strength for toughness: a higher tempering temperature lowers yield and tensile strength and raises impact energy. Because the window is narrow at 890 MPa, the mill controls furnace temperature uniformity tightly and tests a specimen from each heat, and often from the plate ends as well, to confirm the result.

Two consequences follow for the buyer. First, the plate must not be re-heat treated by the fabricator without the producer's agreement, because a second austenitize and quench cycle on a finished plate risks distortion and unpredictable properties. Second, hot forming above the tempering temperature destroys the grade: a S890Q plate heated to 900 degrees C for bending becomes, in effect, an untempered quenched plate and will be both harder and more brittle than specified. Warm forming below the tempering temperature is acceptable within a qualified procedure.

Fabrication Practice for 890 MPa Plate

Cutting is performed by plasma, laser, waterjet or abrasive saw. All thermal processes leave a hardened layer on the cut face, typically 1 to 3 mm deep, which should be ground away before the edge is welded or subjected to cyclic stress. Shearing is only appropriate for thin gauges and produces a work hardened edge that also needs dressing.

Cold bending of S890Q demands attention to springback and to the bend radius. Springback scales with yield strength, so a press brake set for S355 will under-bend S890Q significantly; the bend allowance must be recalculated and the tooling compensated. Bend lines should run transverse to the rolling direction where geometry allows, the bend radius should be generous relative to thickness, and the plate edges should be deburred before bending to prevent crack initiation. Bending a plate that has been plasma cut without edge dressing is a common source of small edge cracks that later grow under fatigue.

Welding follows the same logic as for the L grade but with a lower toughness reserve to protect. Heat input should be controlled within a qualified range: too high widens the softened zone beside the fusion line until the joint strength falls below the parent requirement, too low produces hard microstructures in the coarse grain zone and raises cracking risk. Preheats in the 100 to 150 degrees C band are typical for moderate carbon equivalent, rising for thicker sections and richer heats. Interpass temperature should be monitored and capped, low hydrogen consumables with a diffusible hydrogen limit of about 5 ml per 100 g should be used and stored dry, and welding should not proceed on a surface below the specified preheat or in wind and rain without protection. Post-weld heat treatment is generally avoided because the required temperature would over-temper the parent plate.

Dimensional, Surface and Edge Quality

Dimensional requirements for hot rolled plate come from EN 10029, which sets tolerance classes for thickness, width, length, flatness and edge camber. The default thickness tolerance permits a negative deviation that matters on a 890 MPa plate because the section modulus and the load capacity are both thickness dependent; projects that are weight or strength critical should specify a tightened thickness class and check it with a calibrated gauge at several points per plate rather than at the corners alone.

Surface quality is addressed through EN 10163, which classifies permissible discontinuities and repairs. Rolled-in scale, seams, scratches and edge laminations are the usual findings, and the acceptable depth of any dressing operation is limited as a proportion of thickness. Any welding repair on high strength quenched and tempered plate must be carried out under a qualified procedure with preheat and controlled heat input, and must be recorded against the plate identity.

For thick or fatigue loaded applications, ultrasonic testing to EN 10160 at an agreed quality class provides assurance against internal discontinuities, particularly centre-line segregation and hydrogen flakes. Hydrogen induced cracking is a real risk in high strength plate if the steel is not properly degassed and if the plate is not tempered promptly after quenching, which is one reason the mill route matters as much as the certificate numbers.

Typical Applications and Misapplications

S890Q is used in mobile crane frames and telescopic boom sections, excavator and loader arms, concrete pump booms, drilling rig masts, forestry equipment, heavy truck chassis and suspension components, and lifting attachments such as spreader beams and lifting frames. In all of these the benefit is weight saving at constant load capacity, which translates directly into payload, fuel consumption and axle load compliance. It is also used in stationary structures where a shallow beam depth is architecturally or spatially necessary.

The misapplications follow a pattern. Using S890Q as a wear resistant plate is one: abrasion resistance depends on hardness and microstructure, not on yield strength, and a 890 MPa structural plate will wear faster than a purpose made wear plate at similar hardness. Using it in a cold climate without the L or L1 class is another. A third is using it for a pressure retaining component without checking whether the applicable pressure vessel standard permits a 890 MPa quenched and tempered steel at all. A fourth is assuming that a higher strength plate can be welded with the same procedure as S355: the procedure must be re-qualified, and the heat affected zone, not the weld metal, is usually the limiting region.

Verification at Goods-In

Receiving inspection for S890Q should confirm four things. The plate markings must show grade, heat number and dimensions, and must match the certificate heat numbers exactly. The inspection document should be EN 10204 type 3.1 for structural safety components, reporting actual chemical and mechanical results per heat rather than generic compliance statements. The certificate must show tensile results with both yield and tensile strength inside the specified range, elongation, and impact energy with the test temperature and orientation stated. Where ultrasonic testing or through thickness testing was ordered, the report should be traceable to the individual plate.

A simple hardness check across the plate surface is a useful screening tool on arrival: a plate that shows a wide hardness spread or values inconsistent with 890 MPa tempered martensite may indicate a quench problem, and a plate markedly harder than the certificate suggests may never have been tempered. Any such finding justifies a full re-test before the plate is released to production.

FAQ

Q: What is the difference between S890Q and S890QL?
Both have the same yield and tensile requirements. The L grade adds a verified Charpy class of 30 J at -40 degrees C, while S890Q is normally verified at 0 degrees C with 50 J and is intended for ambient temperature service.

Q: What is the maximum thickness available in S890Q?
The mechanical values above 50 mm drop to 830 MPa minimum yield and 880 to 1100 MPa tensile strength. Plate above 100 mm is outside the usual thickness table and should be discussed with the producer before design is fixed.

Q: Can S890Q plate be bent cold?
Yes, within a qualified procedure. Springback is large because of the 890 MPa yield strength, bend radii must be generous, bend lines should run transverse to rolling where possible, and cut edges must be dressed before bending.

Q: Why is post-weld heat treatment not usual for S890Q?
Stress relief temperatures would temper the parent plate below its specified strength. Where stress relief is essential, it must be agreed with the producer and supported by a procedure qualification including heat affected zone impact tests.

Q: How is S890Q different from a wear resistant plate?
Wear resistance depends on hardness and carbide content, not on yield strength. A 890 MPa structural plate offers high load capacity at low weight but is not designed to resist abrasive wear.

Q: Which documents should accompany an S890Q delivery?
An EN 10204 type 3.1 inspection certificate with actual per heat chemical and mechanical results, plus EN 10160 ultrasonic test reports where specified, and plate markings that match the certificate heat numbers.

Send Inquiry

whatsapp

phone

Email

Inquiry