Apr 09, 2024 Leave a message

16Mo3.pdf

16Mo3 Steel Plate: EN 10028-2 Molybdenum Boiler Plate

What 16Mo3 Plate Is and Where It Comes From

16Mo3 is a molybdenum-alloyed pressure vessel steel defined in EN 10028-2, the part of the European flat products standard that covers non-alloy and alloy steels with specified elevated temperature properties. The designation is descriptive: roughly 0.16% carbon and about 0.3% molybdenum. It belongs to the same family as the German boiler plate tradition of 15Mo3 and is used across Europe and in export projects wherever a design code references EN pressure vessel steels.

Its place in the material selection chart is between plain carbon steel and the chromium-molybdenum grades. Carbon steel such as P265GH is adequate to about 400 °C; 16Mo3 extends useful design strength into the 450–500 °C band; above roughly 530 °C the creep data falls away and the 1% Cr or 2.25% Cr grades take over. Molybdenum is what buys that extra range, because it raises the recrystallisation temperature of the ferrite and stabilises the carbides that carry load at temperature.

In practice 16Mo3 is a workhorse rather than a specialist grade. It is selected for steam drums, boiler shells, heat exchangers, separators and storage vessels where the metal temperature sits modestly above the carbon steel limit and where a full chromoly steel would be technically unnecessary and commercially wasteful.

Chemical Composition to EN 10028-2

The chemistry is deliberately lean, and the narrow carbon range is the part that matters most. Carbon below 0.12% leaves insufficient carbide for creep strength; carbon above 0.20% degrades weldability and toughness in the heat-affected zone. Molybdenum is held to a narrow 0.25–0.35% window, so a heat at either edge of the window behaves differently in a long-term creep application.

Element Requirement, % Practical note
C 0.12–0.20 Strength and creep resistance; upper limit controls weld toughness
Si 0.35 max Deoxidation only; keep low where toughness matters
Mn 0.40–0.90 Hardenability and sulphur control
P 0.025 max Segregation, temper embrittlement, through-thickness ductility
S 0.010 max Inclusion level, lamellar tearing risk in thick sections
Mo 0.25–0.35 The alloying element that sets the elevated temperature capability
Cr 0.30 max Residual from scrap; not a chromoly grade
Ni 0.30 max Residual; affects toughness if allowed to climb
Cu 0.30 max Residual; relevant to hot ductility during forming

Because the residual limits are tight relative to carbon steel, the scrap charge used by the steelmaker is effectively part of the specification. A purchaser receiving a certificate showing chromium or nickel close to the maximum should ask about the residual pattern across the heat, particularly for plate intended for cold forming or for welding under restraint.

Mechanical Properties and Elevated Temperature Behaviour

Room temperature requirements for plate in the usual thickness range are a minimum yield strength of 275 MPa, a tensile range of 440–590 MPa, and a minimum elongation of 22% on a 50 mm gauge length. Both strength figures step down with increasing thickness in the tables of the standard, so a 100 mm plate should not be judged against the 20 mm values.

Property 16Mo3 P265GH for comparison
Minimum yield strength 275 MPa 265 MPa
Tensile strength range 440–590 MPa 410–530 MPa
Minimum elongation, 50 mm 22% 23%
Molybdenum 0.25–0.35% Not specified
Useful design range Up to roughly 500–530 °C, subject to code stress tables Up to roughly 400 °C

The reason to pay for the molybdenum is not room temperature strength, which is almost identical to P265GH. It is the shape of the strength-temperature curve. At 400 °C and above, the molybdenum-bearing steel retains a substantially higher proportion of its room temperature yield strength, and its creep rupture data extend further. Design values for both grades are published as allowable stresses in the applicable code, and those tabulated values, not the room temperature tensile, govern the wall thickness calculation.

Impact requirements are not automatic in the base grade, but most European pressure vessel specifications invoke them through the design code. When impact testing is ordered, agree the test temperature, the specimen orientation, the notch position for thick plate, and whether the tests are performed after simulated post-weld heat treatment. Charpy values taken on as-supplied plate can overstate the toughness of a joint that has spent ten hours at 620 °C.

Delivery Condition, Options and Tolerances

16Mo3 is normally delivered in the normalized condition, designated +N in the standard's delivery condition notation. Normalizing is carried out around 900–930 °C followed by air cooling; it refines the grain structure and homogenises the molybdenum distribution. Where a project calls for it, plate can be supplied normalized and tempered, and thermomechanically rolled material is occasionally agreed for specific thickness ranges, but the default and the safest baseline for pressure equipment is +N.

Three commercial options usually need to be written into the order rather than assumed. First, ultrasonic examination: EN 10160 defines quality classes for the detection of internal discontinuities, and the class must be stated because the default may be no examination at all. Second, through-thickness properties: EN 10164 defines Z15, Z25 and Z35 quality for plate loaded in the through-thickness direction at welded T-joints, and Z quality is a separate designation, not a property of the grade. Third, dimensional tolerance: EN 10029 governs thickness, width, length and flatness, and tighter-than-standard thickness tolerance should be requested explicitly where weight or fit-up is critical.

Surface quality follows EN 10163 for the permissible level of discontinuities and for the repair of surface defects by grinding. A plate that has been dressed extensively should be re-measured, because grinding removes the very material the thickness tolerance was calculated against.

Welding 16Mo3: Preheat, Consumables and Post-Weld Heat Treatment

The grade welds cleanly with conventional processes, but the molybdenum addition changes two parameters. Preheat of roughly 100–150 °C is normal for sections above about 20 mm, rising for thicker or more restrained joints; below that the risk is low but not zero, and workshop temperature should be considered rather than ignored. Consumables should match the parent chemistry: the 0.5% Mo classifications such as AWS A5.5 E7018-A1 for covered electrodes and AWS A5.28 ER70S-A1 for solid wire, or their ISO equivalents, deposit weld metal with creep behaviour close to the parent plate.

Post-weld heat treatment is required for most pressure equipment in this grade and is normally placed in the 600–650 °C range. The purpose is to temper the heat-affected zone and relieve residual stress; the constraint is that the hold must sit below the temperature at which the molybdenum carbides coarsen and strength drops. A hold that is too hot is more damaging than a hold that is slightly cool, and the qualified welding procedure should fix the window rather than leave it to the furnace operator.

Heating and cooling rates above 400 °C should be controlled, typically at a rate related to the maximum section thickness, and thermocouples should be attached to the work rather than to the furnace atmosphere. Where several vessels are treated in one charge, they should share a similar thickness range; thin plate and heavy forging in the same load will not see the same thermal history.

Practical shop issues worth anticipating: weld prep on flame-cut edges needs the hardened layer removed by grinding before the root pass; tack welds should be made with the production consumable and later consumed by the seam; and repairs require their own procedure qualification and their own heat treatment record. Hydrogen cracking in 16Mo3 is uncommon when preheat is respected, and rather more common when a repair is made on cold plate late in the shift.

Forming, Machining and Handling

16Mo3 cold forms well at the strength level involved, and the minimum bend radius in the standard's tables is generous. The practical limits come from plate thickness and from the capacity of the press brake rather than from the steel itself. Hot forming above the recrystallisation temperature is possible, but it destroys the normalized condition and requires re-normalizing afterwards, which is a workshop capability question that should be settled before the order is placed rather than after the shell has been formed.

Machining is unremarkable for a low alloy steel: conventional turning and drilling with carbide tooling and adequate coolant. Drilling thick plate benefits from peck cycles to clear swarf and from sharpening before the edge dulls, because work-hardened surfaces make subsequent reaming difficult. Thermal cutting is normally done by plasma or oxy-fuel, followed by grinding of the cut face and, where the design requires it, magnetic particle or dye penetrant inspection of the prepared edge.

Storage is a real quality issue in humid climates. Plate should be kept clear of the ground, on bearers, with the edges protected, and weld preparations should be capped if the vessel will not be completed promptly. Rust on the surface is generally cosmetic; rust in a weld prep is not, because it introduces hydrogen and oxygen into the root of the joint.

Typical Applications and Grade Selection

The largest single use is boiler and pressure vessel construction: steam drums, boiler shells, headers, and the shells of fired and unfired pressure vessels. Heat exchangers account for another significant share, in shell and channel construction where the design temperature is modestly elevated. Separators, spherical tanks, LPG storage vessels, oil and gas storage tanks, reactor pressure shells and turbine volutes all appear in published descriptions of the grade's applications, and the common thread is a design temperature that exceeds the carbon steel limit without justifying a chromoly steel.

The selection decision is usually made on three questions. What is the design metal temperature, and what does the code stress table allow at that temperature for each candidate grade? What is the minimum design metal temperature, and does the impact requirement favour a fine grain practice grade instead? And what is the wall thickness, since the weight saving from a higher allowable stress must be set against the higher cost per tonne and the additional welding controls?

Where a project specifies an American code rather than a European one, the nearest equivalents are the carbon-manganese silicon grades at the low end and the 1.25Cr-0.5Mo grades at the high end; a direct substitution of 16Mo3 by an American grade requires a documented comparison of chemistry, tensile properties and allowable stress at design temperature, not a visual similarity of the numbers on the certificate.

Purchasing Checklist and Receiving Inspection

An enquiry that produces comparable offers states the following: the full designation (16Mo3 to EN 10028-2), delivery condition (+N), thickness with tolerance class to EN 10029, width and length, ultrasonic examination class to EN 10160, Z-direction quality to EN 10164 where applicable, impact test temperature and energy, maximum residual element levels, surface condition to EN 10163, and the document package required. Without these, different mills quote against different assumptions and the price difference is not a real price difference.

The certificate review is where most problems are caught. Check that the steel grade and delivery condition match the order, that the heat number on the plate matches the certificate, that the product analysis is reported as well as the ladle analysis, that mechanical tests are from the correct orientation and, for thick plate, from the correct location through the thickness, and that heat treatment temperatures and holding times are recorded rather than summarised.

On receipt, measure thickness at a grid of points rather than at a single location, check flatness, look for edge laminations on cut plate, and confirm that markings are legible and traceable. Hold the plate until the ultrasonic report and the heat treatment record have been reviewed against the order. A plate that is dimensionally correct but has no ultrasonic examination when the order required a class is not a conforming delivery, whatever the surface looks like.

FAQ

Q: What does the designation 16Mo3 mean?
It indicates approximately 0.16% carbon and about 0.3% molybdenum, and it is the EN designation for a molybdenum-alloyed pressure vessel steel covered by EN 10028-2.

Q: What is the maximum service temperature for 16Mo3?
The grade is normally used up to roughly 500–530 °C. The actual limit is set by the allowable stress tables in the applicable design code at the design metal temperature, not by a single published number.

Q: Is 16Mo3 delivered normalized?
Yes. The default delivery condition is normalized, shown as +N. Normalized and tempered delivery can be agreed, and any hot forming during fabrication requires re-normalizing afterwards.

Q: Which welding consumables match 16Mo3?
Consumables of the 0.5% Mo classification, such as AWS A5.5 E7018-A1 covered electrodes or AWS A5.28 ER70S-A1 solid wire, together with their ISO equivalents. Matching the molybdenum content keeps weld metal creep behaviour close to the parent plate.

Q: What post-weld heat treatment temperature applies?
A hold in the 600–650 °C range is typical for pressure equipment in this grade, with controlled heating and cooling above 400 °C. The exact window belongs in the qualified welding procedure and should be consistent with the mill's tempering treatment.

Q: What is the difference between 16Mo3 and P265GH?
Room temperature strength is similar, but 16Mo3 contains 0.25–0.35% molybdenum, which gives it useful elevated temperature strength and creep data well beyond the roughly 400 °C practical limit of P265GH.

Q: Is Z35 better than Z15?
Z35 specifies a higher through-thickness ductility than Z25, and Z25 higher than Z15, under EN 10164. The correct grade depends on the through-thickness stress at the joint, and specifying a higher grade than the design needs adds cost without benefit.

Send Inquiry

whatsapp

phone

Email

Inquiry